Abstract
The cyclic deformation and fatigue behavior of the γ-TiAl alloy TNB-V5 is evaluated under thermomechanical load for three different microstructures. For this purpose, strain-controlled thermomechanical fatigue (TMF) tests were carried out with different temperature-strain cycles, different temperature ranges from 400 °C to 800 °C (673 K to 1073 K), and with two different strain ranges to set a fatigue-life relation. Cyclic deformation curves, stress-strain hysteresis loops, and fatigue lives of the tests are presented. The microstructures near-gamma (NG) and duplex (DP) show comparable fatigue lives under all test parameters. The microstructure fully-lamellar (FL) offers longer fatigue lives at the same loading conditions. For a general life prediction, the damage parameter of Smith, Watson, and Topper, P SWT vs fatigue life, is well suitable, if the testing and the application temperature ranges, respectively, include temperatures above the ductile-brittle transition (approximately 750 °C). In the completely brittle material behavior regime the quality of the lifetime prediction is unacceptable. The damage parameter P HL by Haibach and Lehrke shows a comparable correlation to the fatigue life as P SWT. The results are discussed with microstructural investigations.
Similar content being viewed by others
Notes
PHILIPS is a trademark of FEI Company, Hillsboro, OR.
References
Y.-W. Kim and D.M. Dimiduk: Structural Intermetallics 1997, TMS, Warrendale, PA, pp. 531–43.
F. Appel and R. Wagner: Mater. Sci. Eng., 1998, vol. R22, pp. 187–268.
D.M. Dimiduk: Mater. Sci. Eng., 1999, vol. A263, pp. 281–88.
M. Yamaguchi, H. Inui, and K. Ito: Acta Mater., 2000, vol. 48 (1), pp. 307–22.
H. Clemens and H. Kestler: Adv. Eng. Mater., 2000, vol. 2 (9), pp. 551–70.
F. Appel and M. Oehring: Titan und Titanlegierungen, Wiley-VCH, Weinheim, 2002, pp. 39–103.
Y. Shen, X. Ding, F. Wang, Y. Tan, and J.-M. Yang: J. Mater. Sci., 2004, vol. 39, pp. 6583–89.
M. Yoshihara and K. Miura: Intermetallics, 1995, vol. 3, pp. 357–63.
F. Appel, J.D.H. Paul, M. Oehring, and C. Buque: Gamma Titanium Aluminides, TMS, Warrendale, PA, 2003, pp. 139–51.
F. Appel, J.D.H. Paul, M. Oehring, H. Clemens, and F.D. Fischer: Z. Metallkd., 2004, vol. 95 (7), pp. 585–91.
H. Clemens and W. Glatz: Prakt. Met., 1995, special vol. 26, pp. 257–69.
Y.-W. Kim and D.M. Dimiduk: JOM, 1991, vol. 43 (8), pp. 40–47.
P. Schallow: Ph.D. Thesis, Siegen, VDI Verlag, Düsseldorf, Germany, 2005.
V. Bauer: Ph.D. Thesis, Siegen, Shaker Verlag, Herzogenrath, Germany, 2006.
F.O.R. Fischer: Ph.D. Thesis, Siegen, Germany, 2000.
H.-J. Christ, F.O.R. Fischer, and H.J. Maier: Mater. Sci. Eng., 2001, vols. A319–A321, pp. 625–30.
H.J. Maier, F.O.R. Fischer, and H.-J. Christ: ASTM Special Technical Publication, 2003, vol. 1428, pp. 145–63.
P. Schallow and H.-J. Christ: Proc. 5th Int. Conf. on Low Cycle Fatigue, Deutscher Verband für Materialforschung und Prüfung e.V., Berlin, 2004, pp. 195–200.
H.-J. Christ: Mater. Sci. Eng. A, 2007, vols. 468–470, pp. 98–108.
W.F. Cui, C.M. Liu, V. Bauer, and H.-J. Christ: Intermetallics, 2007, vol. 15 (5–6), pp. 675–78.
V. Bauer and H.-J. Christ: Intermetallics, 2009, vol. 17 (5), pp. 370–77.
S.P. Brookes, H.-J. Kühn, B. Skrotzki, H. Klingelhöffer, R. Sievert, J. Pfetzing, and G. Eggeler: Proc. 11th World Conf. on Titanium, The Japan Institute of Metals, Sendai, Japan, 2007, pp. 679–82.
S.P. Brookes, H.-J. Kühn, B. Skrotzki, H. Klingelhöffer, and R. Sievert: Proc. Werkstoffprüfung, Verlag Stahleisen GmbH, Düsseldorf, Germany, 2007, pp. 249–54.
M. Roth and H. Biermann: Scripta Mater., 2006, vol. 54, pp. 137–41.
M. Roth and H. Biermann: Int. J. Fatigue, 2008, vol. 30, pp. 352–56.
P.E. Jones and D. Eylon: Mater. Sci. Eng., 1999, vol. A263, pp. 296–304.
M. Roth: Ph.D. Thesis, TU Bergakademie Freiberg, Freiberg, Germany, 2009, submitted.
K.N. Smith, P. Watson, and T.H. Topper: J. Mater., 1970, vol. 5 (4), pp. 767–78.
E. Haibach and H.P. Lehrke: Arch. Eisenhüttenwes., 1976, vol. 47 (10), pp. 623–28.
Acknowledgments
This work was supported by Deutsche Forschungsgemeinschaft (Bi 418/10). Further thanks are expressed to Dr. H. Kestler, Plansee AG (Reutte, Austria), for providing the material, and to Dr. F. Pyczak, GKSS (Geesthacht), and Dr. V. Klemm, Institut für Werkstoffwissenschaft, TU Bergakademie Freiberg, for their support in the TEM work.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted March 22, 2009.
Rights and permissions
About this article
Cite this article
Roth, M., Biermann, H. Thermomechanical Fatigue Behavior of the Intermetallic γ-TiAl Alloy TNB-V5 with Different Microstructures. Metall Mater Trans A 41, 717–726 (2010). https://doi.org/10.1007/s11661-009-0119-4
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-009-0119-4