Abstract
The microstructural changes in a single-crystal Ni-base superalloy, CMSX-4, that might occur during the processes of repair and recoating of hot section components for advanced gas turbines were studied. It is shown that the cellular γ/γ′ microstructure is formed when the material is subjected to local plastic straining, followed by the reheat treatments during the course of damage recovery. The formation of cellular microstructure in the material led to the remarkably reduced fatigue strength. In order to reduce or prevent the preceding undesirable effect resulting from cellular microstructure, a new method based on applying overlay coating technique was developed. The method is based on an idea that the alloying elements that are depleted in base alloys could be supplemented via the overlay coating. An X alloy, which contains grain boundary strengthening elements, was selected and coated on the CMSX-4 with the cellular microstructure by low-pressure plasma spraying. The fatigue tests on the coated CMSX-4 specimens demonstrated the effectiveness of the method. The observations of the crack initiation site, the fatigue fracture mode, the crack density in the cellular transformed area, and the crack propagation morphologies near the prior interface strongly supported the validity of this approach. The method is expected to build a road to a so-called damage cure (or recovery) coating.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
B.B. Seth: Superalloys 2000, T. Pollock, ed., TMS, Warrendale, PA, 2000, pp. 3–13.
J. Stinger and R. Viswanathan: Proc. ASM 1993 Materials Week ’93, ASM, Materials Park, OH, 1993, pp. 1–10.
R. Curtis: ASME Paper GT-2001, ASME, New York, 2001, paper no. 569.
W.M. Miglietti: ASME paper GT-2001, ASME, 2001, paper no. 501.
S.D. Bond and J.W. Martin: J. Mater. Sci., 1984, vol. 19, pp. 3867–72.
A. Porter and B. Ralph: J. Mater. Sci., 1981, vol. 16, pp. 707–13.
P. Portella: in Microstructure and Mechanical Properties of Metallic High Temperature Materials, H. Mughrabi, ed., DFG, Berlin, 1999, pp. 441–53.
W.S. Walston, J.C. Schaeffer, and W.H. Murphy: Superalloys ’96, 1996, pp. 9–18.
M. Okazaki, T. Hiura, and T. Suzuki: in Superalloys 2000, T. Pollock, ed., 2000, pp. 505–14.
M. Okazaki, R. Takaku, K. Namba, and Y. Harada: Soc. Mater. Sci., Jpn., 2002, vol. 51, pp. 611–17 (in Japanese).
M. Okazaki, T. Hiura, and T. Suzuki: Mater. Sci. Res. Int., 2003, vol. 9, pp. 55–60.
M. Okazaki, I. Ohtera, and Y. Harada: Soc. Mater. Sci., Jpn., 2003, vol. 52, pp. 146–53 (in Japanese).
For example, F.R.N. Nabarro: Metall. Mater. Trans. A, 1996, vol. 27A, pp. 513–23.
U. Krupp and H.J. Christ: Metall. Mater. Trans. A, 2000, vol. 31A, pp. 47–56.
For example, D. Broek: Elementary Engineering Fracture Mechanics, Noordhoff Int. Pub., Leyden, The Netherlands, 1974, ch. 3.
C. Liu, C.L. White, and J. Horton: Acta Metall., 1985, vol. 33, p. 213.
K. Schneider and H.W. Gruling: Thin Solid Films, 1981, vol. 84, pp. 29–36.
A. Strang and E. Lang: in High Temperature Alloys for Gas Turbines, R. Brunetaud, ed., Riedel Publishing Co., Liege, 1982, pp. 469–506.
M. Okazaki, H. Yamada, and S. Nohmi: Metall. Mater. Trans. A, 1996, vol. 26A, pp. 1021–33.
M.Y. He and J.W. Hutchinson: Int. J. Solids Struct., 1989, vol. 25, pp. 1053–66.
K. Aoki and O. Izumi: Nippon Kinzoku Gakkai-shi, 1979, vol. 43, pp. 1190–97 (in Japanese).
E.M. Schulson, T.P. Weibs, and I. Baker: Acta Metall., 1986, vol. 34, pp. 1395–1404.
D.A. Muller, S. Subramanian, P.E. Boston, and S.L. Sass: Acta Metall., 1996, vol. 44, pp. 1637–45.
R.P. Messer and C.L. Briant: Acta Metall., 1982, vol. 30, pp. 457–67.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Okazaki, M., Ohtera, I. & Harada, Y. Damage repair in CMSX-4 alloy without fatigue life reduction penalty. Metall Mater Trans A 35, 535–542 (2004). https://doi.org/10.1007/s11661-004-0364-5
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11661-004-0364-5