Skip to main content
SpringerLink
Log in

Evaluating rockfalls at a historical settlement in the Ihlara Valley (Cappadocia, Turkey) using kinematic, numerical, 2D trajectory, and risk rating methods

  • Original Article
  • Published:
Journal of Mountain Science Aims and scope Submit manuscript

Abstract

Rockfalls are one of the most dangerous natural events in hilly terrains, and they substantially threaten residential areas and transport corridors in these environments. This study is aimed to analyze the risk of rockfall from a slope to nearby houses in a historical settlement with past rockfall histories. It contains numerous applications to study rockfall danger from different points of view (e.g., kinematics, numerical stability analysis, risk assessment, 2D trajectory). The rockfall kinematics revealed the statistics for different structurally controlled failure modes among the surveyed slope discontinuities, especially wedge type and block toppling were the most significant ones. Finite element analysis showed that the slope was stable under the natural condition with a safety factor of 2.19. The rockfall risk rating system calculated a medium risk for the houses downstream. Based on the field measurements, a possible rockfall profile was determined and located as an input in the 2D rockfall trajectory program. The rigid-body impact model runs utilized various shapes and sizes of blocks to simulate the rockfall events realistically. According to the 2D trajectory model results, there was no rockfall danger for the investigated downslope houses. The study showed the importance of using different analysis techniques to solve rockfall risk in protected areas based on scientific and rational approaches.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  • Agliardi F, Crosta G (2003) High resolution three-dimensional numerical modelling of rockfalls. Int J Rock Mech Min Sci 40: 455–471. https://doi.org/10.1016/S1365-1609(03)00021-2

    Article  Google Scholar 

  • Akin M, Dinçer İ, Ok A, et al. (2021) Assessment of the effectiveness of a rockfall ditch through 3-D probabilistic rockfall simulations and automated image processing. Eng Geol 283: 106001. https://doi.org/10.1016/j.enggeo.2021.106001

    Article  Google Scholar 

  • Alejano LR, Gonzalez J, Muralha J (2012) Comparison of different techniques of tilt testing and basic friction angle variability assessment. Rock Mech Rock Eng 45: 1023–1035. https://doi.org/10.1007/s00603-012-0265-7

    Article  Google Scholar 

  • Alejano LR, Muralha J, Ulusay R, et al. (2018). ISRM suggested method for determining the basic friction angle of planar rock surfaces by means of tilt tests. Rock Mech Rock Eng 51(12): 3853–3859. https://doi.org/10.1007/s00603-018-1627-6

    Article  Google Scholar 

  • Alemdag S, Zeybek HI, Kulekci G (2019) Stability evaluation of the Gümüşhane-Akçakale cave by numerical analysis method. J Mount Sci 16(9): 2150–2158. https://doi.org/10.1007/s11629-019-5529-1

    Article  Google Scholar 

  • Ansari MK, Ahmad M, Singh R, Singh TN (2015) Correlation between Schmidt hardness and coefficient of restitution of rocks. J African Earth Sci 104: 1–5. https://doi.org/10.1016/j.jafrearsci.2015.01.005

    Article  Google Scholar 

  • Ansari MK, Ahmad M, Singh R, Singh TN (2018) 2D and 3D rockfall hazard analysis and protection measures for Saptashrungi Gad Temple, Vani, Nashik, Maharashtra — A case study. J Geol Soc India 91:47–56. https://doi.org/10.1007/s12594-018-0819-8

    Article  Google Scholar 

  • Antoniou AA (2015) Evaluation of a rockfall risk management system for mountainous and touristic paths. In: Engineering Geology for Society and Territory-Vol. 2. pp 1925–1929. https://doi.org/10.1007/978-3-319-09057-3_341

  • Asteriou P, Saroglou H, Tsiambaos G (2012) Geotechnical and kinematic parameters affecting the coefficients of restitution for rockfall analysis. Int J Rock Mech Min Sci 54: 103–113. https://doi.org/10.1016/j.ijrmms.2012.05.029

    Article  Google Scholar 

  • Attewell P, Farmer I (1976) Principles of Engineering Geology. Chapman & Hall: London. p 1045.

    Book  Google Scholar 

  • Aydar E, Schmitt AK, Çubukçu HE, et al. (2012) Correlation of ignimbrites in the central Anatolian volcanic province using zircon and plagioclase ages and zircon compositions. J Volcanol Geotherm Res 213–214: 83–97. https://doi.org/10.1016/j.jvolgeores.2011.11.005

    Article  Google Scholar 

  • Azami A, Yacoub T, Curran JH (2012) Effects of strength anisotropy on the stability of slopes. In: 65th Canadian Geotechnical Conference, CGS Geo-Manitoba, Winnepeg.

  • Bar N, Nicoll S, Pothitos F (2016) Rockfall trajectory field testing, model simulations and considerations for steep slope design in hard rock. In: Proceedings of the First Asia Pacific Slope Stability in Mining Conference, Australian Centre for Geomechanics, Perth. https://doi.org/10.36487/ACG_rep/1604_29_Bar

  • Barton N (1976) The shear strength of rock and rock joints. Int J Rock Mech Min Sci Geomech Abstr 13: 255–279. https://doi.org/10.1016/0148-9062(76)90003-6

    Article  Google Scholar 

  • Barton N (2013). Shear strength criteria for rock, rock joints, rockfill and rock masses: Problems and some solutions. J Rock Mech Geotech Eng 5(4): 249–261. https://doi.org/10.1016/j.jrmge.2013.05.008

    Article  Google Scholar 

  • Barton NR, Choubey V (1977) The shear strength of rock joints in theory and practice. Rock Mech 10: 1–54. https://doi.org/10.1007/BF01261801

    Article  Google Scholar 

  • Barton NR, Lien R, Lunde J (1974) Engineering classification of rock masses for the design of tunnel support. Rock Mech 6(4):189–236. https://doi.org/10.1007/BF01239496

    Article  Google Scholar 

  • Basson FRP (2012) Rigid body dynamics for rockfall trajectory simulation. In: Proc. 46th US Rock Mech. & Geomech. Symp. 24–27 June 2012, ARMA, Chicago.

    Google Scholar 

  • Beekman PH (1966) Geology of Aksaray-Gelveri-Çınarlı regions. MTA Report. (In Turkish)

  • Bell FG (2007) Engineering Geology, Butterworth-Heinemann, 2nd Ed. p 581.

  • Bieniawski ZT (1989) Engineering Rock Mass Classifications. John Wiley & Sons: New York. p 251.

    Google Scholar 

  • Binal A (1996) Investigation of the instability mechanisms observed in volcano-sedimentary rocks at Aksaray-Ihlara Valley. M.Sc. Thesis, Hacettepe University, Ankara. (In Turkish).

    Google Scholar 

  • Binal A, Ercanoğlu M (2010). Assessment of rockfall potential in the Kula (Manisa, Turkey) geopark region. Environ Earth Sci 61(7): 1361–1373. https://doi.org/10.1007/s12665-010-0454-1

    Article  Google Scholar 

  • Bozzolo D, Pamini R (1986) Simulation of rock falls down a valley side. Acta Mechanica 63: 113–130. https://doi.org/10.1007/BF01182543

    Article  Google Scholar 

  • Brawner CO, Wyllie D (1976) Rock slope stability on railway projects. Am Railw Eng Assoc Bull 656: 449–474.

    Google Scholar 

  • Budetta P (2004) Assessment of rockfall risk along roads. Nat Hazards Earth Syst Sci 4: 71–81. https://doi.org/10.5194/nhess-4-71-2004

    Article  Google Scholar 

  • Budetta P, Santo A (1994) Morphostructural evolution and related kinematics of rockfalls in Campania (southern Italy): A case study. Eng Geol 36: 197–210. https://doi.org/10.1016/0013-7952(94)90004-3

    Article  Google Scholar 

  • Chau KT, Wong RHC, Wu JJ (2002) Coefficient of restitution and rotational motions of rockfall impacts. Int J Rock Mech Min Sci 39: 69–77. https://doi.org/10.1016/S1365-1609(02)00016-3

    Article  Google Scholar 

  • Dadashzadeh N, Aras C, Yesiloglu-Gultekin N, et al. (2014) Analysis of potential rockfalls and protection measures for the Mardin Castle, Turkey. In: Eurock 2014, ISRM European Regional Symposium, Vigo. pp 1231–1236.

  • Deere DU, Miller RP (1966) Engineering classification and index properties for intact rocks. Tech Rep Air Force Weapons Lab, New Mexico, no AFNL-TR-65–116.

    Book  Google Scholar 

  • Dinçer I, Orhan A, Frattini P, et al. (2016) Rockfall at the heritage site of the Tatlarin Underground City (Cappadocia, Turkey). Nat Hazards 82(2): 1075–1098. https://doi.org/10.1007/s11069-016-2234-z

    Article  Google Scholar 

  • Doğan U, Koçyiğit A, Yılmaz E (2019) Geomorphological evolutionary history of the Melendiz River Valley, Cappadocia, Turkey. Mediter Geosci Rev 1(2): 203–22. https://doi.org/10.1007/s42990-019-00012-6

    Article  Google Scholar 

  • Dorren LKA (2003) A review of rockfall mechanics and modelling approaches. Progress in Physical Geography 27(1): 69–87. https://doi.org/10.1191/0309133303pp359ra

    Article  Google Scholar 

  • Dorren LKA, Berger F, Putters US (2006) Real-size experiment sand 3-D simulation of rockfall on forested and non-forested slopes. Nat Hazards Earth Syst Sci 6: 145–153. https://doi.org/10.5194/NHESS-6-145-2006

    Article  Google Scholar 

  • Eberhardt E, Stead D, Coggan J, Willenberg H (2002) An integrated numerical analysis approach to the Randa rockslide. Proceedings of the First European Conference on Landslides, Prague. pp 355–362.

  • Evans SG, Hungr O (1993) The assessment of rockfall hazard at the base of talus slopes. Canadian Geotech J 30: 620–636. https://doi.org/10.1139/t93-054

    Article  Google Scholar 

  • Ferrari F, Giacomini A, Thoeni K (2016) Qualitative rockfall hazard assessment: a comprehensive review of current practices. Rock Mech Rock Eng 49(7): 2865–2922. https://doi.org/10.1007/s00603-016-0918-z

    Article  Google Scholar 

  • Franklin JA, Wood DF, Senior SA, Blair JA, Wright J (2013) RHRON: Ontario rockfall hazard rating system-field procedures manual, Ontario Ministry of Transportation Materials Engineering and Research Office Report, MERO-043.

  • Fu W, Liao Y (2010) Non-linear shear strength reduction technique in slope stability calculation. Compute Geotech 37(3): 288–298. https://doi.org/10.1016/j.compgeo.2009.11.002

    Article  Google Scholar 

  • Giani GP (1992) Rock Slope Stability Analysis. Rotterdam: Balkema. p 361.

    Google Scholar 

  • Gonzalez J, Gonzalez-Pastoriza N, Castro U, et al. (2014) Considerations on the laboratory estimate of the basic friction angle of rock joints. In: Rock Engineering and Rock Mechanics: Structures in and on Rock Masses, CRC Press: London. pp 199–204. https://doi.org/10.1201/b16955-31

    Chapter  Google Scholar 

  • Goodman RE (1989) Introduction to Rock Mechanics, 2nd Edition. John Wiley & Sons: New York, p 562.

    Google Scholar 

  • Hammah RE, Yacoub T, Corkum B, Curran JH (2008) The practical modelling of discontinuous rock masses with finite element analysis. In: 42nd US Rock Mech Symp, San Francisco, USA. pp 56–63.

  • Hammah RE, Yacoub T, Corkum B, et al. (2007). Analysis of blocky rock slopes with finite element shear strength reduction analysis. In: 1st Canada-U.S. Rock Mechanics Symposium, Vancouver, Canada. pp 329–334.

  • Hammah RE Yacoub T, Curran JH (2009) Variation of failure mechanisms of slopes in jointed rock masses with changing scale. In: 3rd CANUS Rock Mech Symp (Paper No. 3956), Toronto.

  • Hoek E (2008) Practical Rock Engineering, 2008 Edition, Evert Hoek Consulting Engineer Inc., Vancouver, Canada, p 237.

    Google Scholar 

  • Hoek E, Bray JW (1991) Rock Slope Engineering. Elsevier Science Publishing: New York. p 358.

    Google Scholar 

  • Hoek E, Carranza-Torres C, Corkum B (2002) Hoek-Brown failure criterion—2002 edition. In: 1st North American rock mechanics symposium, Toronto. pp267–273.

  • Kobayashi Y, Harp EL, Kagawa T (1990) Simulation of rockfalls triggered by earthquakes. Rock Mech Rock Eng 23: 1–20. https://doi.org/10.1007/BF01020418

    Article  Google Scholar 

  • Marinos P, Hoek E (2000) GSI: a geologically friendly tool for rock mass strength estimation. In: Proc. Int. Conf. on Geotech. & Geol. Eng, GeoEng 2000, Technomic Publ: Melbourne. pp 1422–1442.

    Google Scholar 

  • Mas Ivars D (2010) Bonded particle model for jointed rock mass. (Ph.D. Thesis). KTH-Engineering Geology and Geophysics Research Group, Royal Institute of Technology (KTH).

  • Mineo S (2020) Comparing rockfall hazard and risk assessment procedures along roads for different planning purposes. J Mt Sci 17(3): 653–669. https://doi.org/10.1007/s11629-019-5766-3

    Article  Google Scholar 

  • Mineo S, Pappalardo G, Mangiameli M, et al. (2018) Rockfall analysis for preliminary hazard assessment of the cliff of Taormina Saracen Castle (Sicily). Sustainability 10(2):417.10.3390/su10020417

  • Mineo S, Pappalardo G, Onorato S (2021) Geomechanical characterization of a rock cliff hosting a cultural heritage through ground and UAV rock mass surveys for its sustainable fruition. Sustainability 13: 924. https://doi.org/10.3390/su13020924

    Article  Google Scholar 

  • Ozturk HS, Kocaman S, Gokceoglu C (2019) A low-cost approach for determination of discontinuity orientation using smartphone images and application to a part of Ihlara Valley (Central Turkey). Eng Geol 254: 63–75. https://doi.org/10.1016/j.enggeo.2019.04.011

    Article  Google Scholar 

  • Pain A, Kanungo DP, Sarkar S (2014) Rock slope stability assessment using finite element-based modelling — examples from the Indian Himalayas. Geomech Geoengng: An Int J 9(3): 215–230. https://doi.org/10.1080/17486025.2014.883465

    Article  Google Scholar 

  • Pantelidis L (2009) Rock slope stability assessment through rock mass classification systems. Int J Rock Mech Min Sci 46(2): 315–325. https://doi.org/10.1016/j.ijrmms.2008.06.003

    Article  Google Scholar 

  • Pappalardo G, Mineo S (2015) Rockfall hazard and risk assessment: The promontory of the pre-Hellenic village Castelmola case, north-eastern Sicily (Italy). In: Engineering Geology for Society and Territory — Vol. 2. pp 1989–1993. https://doi.org/10.1007/978-3-319-09057-3_353

  • Pierson LA, Davis SA, Van Vickle R (1990) The Rockfall Hazard Rating System Implementation Manual, Federal Highway Administration (FHWA), report FHWA-OR-EG-90-01, FHWA. US Department of Transportation, Oregon.

    Google Scholar 

  • Ritchie AM (1963) Evaluation of rockfall and its control: Highway Research Record. No. 17, Washington DC, pp. 13–28.

  • Robotham ME, Wang H, Walton G (1995) Assessment of risk from rockfall from active and abandoned quarry slopes. IMM, Section A, 104: 25–33. https://doi.org/10.1016/0148-9062(95)93408-H

    Google Scholar 

  • Rocscience Inc. (2020a). Dips Version 8.0 — graphical and statistical analysis of orientation data. Toronto, Ontario, Canada. https://www.rocscience.com. (Accessed 6 July 2020)

  • Rocscience Inc. (2020b). RocData Version 5.0 — rock and soil strength data analysis. Toronto, Ontario, Canada. https://www.rocscience.com. (Accessed 8 July 2020)

  • Rocscience Inc. (2020c). RS2 Version 2019 — finite element analysis for excavations and slopes. Toronto, Ontario, Canada. https://www.rocscience.com. (Accessed 8 July 2020)

  • Rocscience Inc. (2020d). RocFall Version 8.0 — statistical analysis of rockfalls. Toronto, Ontario, Canada. https://www.rocscience.com. (Accessed 10 July 2020)

  • Official Gazette (1993) Council of Ministers Decision on Disaster Exposed Zone for Enlisted Settlements, 20 December 1993, Article No. 93/5204. (In Turkish)

  • Qian ZG, Li AJ, Lyamin AV, Wang CC (2017) Parametric studies of disturbed rock slope stability based on finite element limit analysis methods. Comp Geotech 81: 155–166. https://doi.org/10.1016/j.compgeo.2016.08.012

    Article  Google Scholar 

  • San NE, Topal T, Akin MK (2020) Rockfall hazard assessment around Ankara Citadel (Turkey) using rockfall analyses and hazard rating system. Geotech Geol Eng 38: 3831–3851. https://doi.org/10.1007/s10706-020-01261-1

    Article  Google Scholar 

  • Santi PM, Russell CP, Higgins JD, Spriet JI (2009) Modification and statistical analysis of the Colorado rockfall hazard rating system. Eng Geol 104(1): 55–65. https://doi.org/10.1016/j.enggeo.2008.08.009

    Article  Google Scholar 

  • Sarı M, Çömlekçiler F (2007) Investigation of discontinuities observed in Kizilkaya ignimbrite and description of the rock mass. J Fac Eng Arch Selcuk Univ 23(1–2): 207–216. (In Turkish)

    Google Scholar 

  • Sari M (2009) The stochastic assessment of strength and deformability characteristics for a pyroclastic rock mass. Int J Rock Mech Min Sci 46(3): 613–626. https://doi.org/10.1016/j.ijrmms.2008.07.007

    Article  Google Scholar 

  • Sari M (2019) Stability analysis of cut slopes using empirical, kinematical, numerical, and limit equilibrium methods: the case of old Jeddah-Mecca road (Saudi Arabia). Environ Earth Sci 78(21): 621. https://doi.org/10.1007/s12665-019-8573-9

    Article  Google Scholar 

  • Sari M (2021) Secondary toppling failure analysis and optimal support design for ignimbrites in the Ihlara Valley (Cappadocia, Turkey) by finite element method (FEM). Geotech Geol Eng 39(7): 5135–5160. https://doi.org/10.1007/s10706-021-01819-7

    Article  Google Scholar 

  • Sarikaya MA, Çiner A, Zreda M (2015). Fairy chimney erosion rates on Cappadocia ignimbrites, Turkey: Insights from cosmogenic nuclides. Geomorphology 234: 182–191. https://doi.org/10.1016/j.geomorph.2014.12.039

    Article  Google Scholar 

  • Saroglou H, Marinos V, Marinos P, Tsiambaos G (2012) Rockfall hazard and risk assessment: an example from a high promontory at the historical site of Monemvasia, Greece. Nat Hazards Earth Syst Sci 12: 1823–1836. https://doi.org/10.5194/nhess-12-1823-2012

    Article  Google Scholar 

  • Sazid M (2019) Analysis of rockfall hazards along NH-15: a case study of Al-Hada road. Int J Geo-Eng 10(1): 1 https://doi.org/10.1186/s40703-019-0097-3

    Article  Google Scholar 

  • Shakoor A, Woodard MJ (2005) Development of a rockfall hazard rating matrix for the state of Ohio. Kent State University, FHWA/OH-2005/005, Kent, Ohio. p 369.

    Google Scholar 

  • Spadari M, Giacomini A, Buzzi O, et al. (2012) In situ rockfall testing in New South Wales, Australia. Int J Rock Mech Min Sci 49: 84–93. https://doi.org/10.1016/j.ijrmms.2011.11.013

    Article  Google Scholar 

  • Stimpson B (1981) A suggested technique for determining the basic friction angle of rock surfaces using core. Int J Rock Mech Min Sci Geomech Abstr 18: 63–65. https://doi.org/10.1016/0148-9062(81)90266-7

    Article  Google Scholar 

  • Şimşek Ş (1997) Geology of Ihlara (Cappadocia) Special Environmental Protection Area and hydrogeological and hydrogeochemical investigation of thermal resources in the region and recommendations for protection. Aksaray Governorate, Provincial Directorate of Culture and Tourism. p 81. (In Turkish)

  • Taşpınar M (2015) Evaluation of rockfalls along Ihlara Valley (Aksaray). M.Sc. Thesis, Aksaray University, p 57. (In Turkish)

  • Topal T, Akin M, Ozden UA (2007) Assessment of rockfall hazard around Afyon Castle, Turkey. Environ Geol 53:191–200. https://doi.org/10.1007/s00254-006-0633-2

    Article  Google Scholar 

  • Tunusluoglu MC, Zorlu K (2009) Rockfall hazard assessment in a cultural and natural heritage (Ortahisar Castle, Cappadocia, Turkey). Environ Geol 56(5): 963–972. https://doi.org/10.1007/s00254-008-1198-z

    Article  Google Scholar 

  • Ulamiş K, Kılıç R (2020) Combined instability assessment and rockfall hazard in volcanic rocks (Keçiören, Ankara). Arabian J Geosci 13:1–10. https://doi.org/10.1007/s12517-020-05338-2

    Article  Google Scholar 

  • Ulusay R, Hudson JA (2007). The Complete ISRM Suggested Methods for Rock Characterization, Testing and Monitoring: 1974–2006. ISRM Turkish National Group, Ankara, Turkey. p 628.

    Google Scholar 

  • Ulusay R, Sönmez H (2002) Engineering Properties of Rock Masses. TMMOB Chapter of Geological Engineers, Ankara. p 243. (In Turkish)

    Google Scholar 

  • UN Glossary (2020). United Nations Network on Public Administration-UNPAN, New York, USA. http://www.unpan.org/Directories/Glossary/ (Accessed 15 August 2020)

  • Vick LM, Zimmer V, White C, et al. (2019) Significance of substrate soil moisture content for rockfall hazard assessment. Nat Hazards Earth Syst Sci 19(5): 1105–1117. https://doi.org/10.5194/nhess-19-1105-2019

    Article  Google Scholar 

  • Vijayakumar S, Yacoub T, Curran JH (2011) A study of rock shape and slope irregularity on rock fall impact distance. In: 45th US Rock Mechanics/Geomechanics Symposium (ARMA), San Francisco, CA.

  • Wyllie DC, Mah CW (2004). Rock Slope Engineering: Civil and Mining, 4th eds. Spon Press: New York. p 431.

    Google Scholar 

  • Yan P, Zhang J, Kong X, Fang Q (2020) Numerical simulation of rockfall trajectory with consideration of arbitrary shapes of falling rocks and terrain. Comput Geotech 122: 103511. https://doi.org/10.1016/j.compgeo.2020.103511

    Article  Google Scholar 

  • Youssef AM, Maerz NH (2012) Development, justification, and verification of a rock fall hazard rating system. Bull Eng Geol Environ 71:171–186. https://doi.org/10.1007/s10064-010-0339-2

    Article  Google Scholar 

  • Zorlu K, Tunusluoglu MC, Gorum T, et al. (2011). Landform effect on rockfall and hazard mapping in Cappadocia (Turkey). Environ Earth Sci 62(8): 1685–1693. https://doi.org/10.1007/s12665-010-0653-9

    Article  Google Scholar 

Download references

Acknowledgements

The author would like to thank the Editor and three anonymous reviewers for their valuable comments and constructive criticism that considerably improved the original submission.

Author information

Authors and Affiliations

  1. Department of Mining Engineering, Aksaray University, Aksaray, 68100, Turkey

    Mehmet Sari

Authors
  1. Mehmet Sari
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Mehmet Sari.

Electronic supplementary material

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sari, M. Evaluating rockfalls at a historical settlement in the Ihlara Valley (Cappadocia, Turkey) using kinematic, numerical, 2D trajectory, and risk rating methods. J. Mt. Sci. 19, 3346–3369 (2022). https://doi.org/10.1007/s11629-022-7412-8

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11629-022-7412-8

Keywords

Search

Navigation