Abstract
In this paper, a novel heat sink which coupling natural convection and phase transition was designed to meet the cooling requirements of distribution level static synchronous compensator (DSTATCOM). The two inclined evaporation substrates can meet the requirements for the parallel operation of DSTATCOM and the working medium R245fa was driven by gravity and buoyancy in the heat sink. The influence of filling ratio and heating power on the thermal performance of the heat sink was investigated experimentally and theoretically. The experimental results showed that the filling ratio and heating power had a significant influence on the thermal performance of the heat sink. At the ambient temperature of 25°C, the heat sink could start up successfully at different heating power and filling ratio. Meanwhile, the heat sink achieved good heat dissipation performance as the maximum temperature of two evaporation substrates were 60.14°C and 67.85°C while the heating power was 3000 W and the filling ratio was 80%. The heat transfer resistance between two evaporation substrates and condensation substrates were 6.6×10−3°C/W and 1.2×10−2°C/W at the same working condition. Additionally, the experimental results showed a good agreement with the calculated results.
Similar content being viewed by others
References
Charles R, Wang C C. A novel heat dissipation fin design applicable for natural convection augmentation. Int Commun Heat Mass Transfer, 2014, 59: 24–29
Senthilkumar R, Nandhakumar A J D, Prabhu S. Analysis of natural convective heat transfer of nano coated aluminium fins using Taguchi method. Heat Mass Transfer, 2013, 49: 55–64
Arbaban M, Salimpour M R. Enhancement of laminar natural convective heat transfer in concentric annuli with radial fins using nanofluids. Heat Mass Transfer, 2015, 51: 353–362
Huang G J, Wong S C, Lin C P. Enhancement of natural convection heat transfer from horizontal rectangular fin arrays with perforations in fin base. Int J Thermal Sci, 2014, 84: 164–174
Xie Z H, Chen L G, Sun F R. Comparative study on constructal optimizations of T-shaped fin based on entransy dissipation rate minimization and maximum thermal resistance minimization. Sci China Technol Sci, 2011, 54: 1249–1258
Tari I. Passive cooling assembly for flat panel displays with integrated high power components. IEEE Trans Consumer Electron, 2009, 55: 1707–1713
Park K T, Kim H J, Kim D K. Experimental study of natural convection from vertical cylinders with branched fins. Exp Thermal Fluid Sci, 2014, 54: 29–37
Ahmadi M, Mostafavi G, Bahrami M. Natural convection from rectangular interrupted fins. Int J Thermal Sci, 2014, 82: 62–71
Micheli L, Reddy K S, Mallick T K. General correlations among geometry, orientation and thermal performance of natural convective micro-finned heat sinks. Int J Heat Mass Transfer, 2015, 91: 711–724
Joo Y, Kim S J. Comparison of thermal performance between plate-fin and pin-fin heat sinks in natural convection. Int J Heat Mass Transfer, 2015, 83: 345–356
Karami M, Yaghoubi M, Keyhani A. Experimental study of natural convection from an array of square fins. Exp Thermal Fluid Sci, 2018, 93: 409–418
Feng S, Shi M, Yan H, et al. Natural convection in a cross-fin heat sink. Appl Thermal Eng, 2018, 132: 30–37
Kemme J E. Ultimate heat-pipe performance. IEEE Trans Electron Devices, 1969, 16: 717–723
Wilson W E. An analysis of the heat pipe as a heat sink for solid-state RF sources. IEEE Trans Electron Devices, 1970, 17: 1013–1014
Ivanova M, Avenas Y, Schaeffer C, et al. Heat pipe integrated in direct bonded copper (DBC) technology for cooling of power electronics packaging. IEEE Trans Power Electron, 2006, 21: 1541–1547
Mizuta K, Fukunaga R, Fukuda K, et al. Development and characterization of a flat laminate vapor chamber. Appl Thermal Eng, 2016, 104: 461–471
Kamenova L, Avenas Y, Schaeffer C, et al. DBC technology for extremely thin flat heat pipes. IEEE Trans Ind Applicat, 2009, 45: 1763–1769
Joung W, Gam K S, Kim Y G, et al. Hydraulic operating temperature control of a loop heat pipe. Int J Heat Mass Transfer, 2015, 86: 796–808
Zhou G, Li J, Lv L. An ultra-thin miniature loop heat pipe cooler for mobile electronics. Appl Thermal Eng, 2016, 109: 514–523
Tharayil T, Asirvatham L G, Rajesh S, et al. Thermal management of electronic devices using combined effects of nanoparticle coating and graphene-water nanofluid in a miniature loop heat pipe. IEEE Trans Compon Packag Manufact Technol, 2018, 8: 1241–1253
He S, Liu Z C, Wang D D, et al. Investigation of the flat disk-shaped LHP with a shared compensation chamber. Appl Thermal Eng, 2016, 104: 139–145
Nishikawara M, Nagano H. Optimization of wick shape in a loop heat pipe for high heat transfer. Int J Heat Mass Transfer, 2017, 104: 1083–1089
Kumar P, Wangaskar B, Khandekar S, et al. Thermal-fluidic transport characteristics of bi-porous wicks for potential loop heat pipe systems. Exp Thermal Fluid Sci, 2018, 94: 355–367
Li X, Zhu K, Li H, et al. Performance comparison regarding loop heat pipes with different evaporator structures. Int J Thermal Sci, 2019, 136: 86–95
Zhang X, Shen J, He W, et al. Comparative study of a novel liquid-vapour separator incorporated gravitational loop heat pipe against the conventional gravitational straight and loop heat pipes — Part I: Conceptual development and theoretical analyses. Energy Convers Manage, 2015, 90: 409–426
Zhang X, Shen J, He W, et al. Comparative study of a novel liquid-vapour separator incorporated gravitational loop heat pipe against the conventional gravitational straight and loop heat pipes — Part II: Experimental testing and simulation model validation. Energy Convers Manage, 2015, 93: 228–238
Sun X, Ling L, Liao S, et al. A thermoelectric cooler coupled with a gravity-assisted heat pipe: An analysis from heat pipe perspective. Energy Convers Manage, 2018, 155: 230–242
Rehman T, Ali H M, Saieed A, et al. Copper foam/PCMs based heat sinks: An experimental study for electronic cooling systems. Int J Heat Mass Transfer, 2018, 127: 381–393
Rehman T, Ali H M. Experimental investigation on paraffin wax integrated with copper foam based heat sinks for electronic components thermal cooling. Int Commun Heat Mass Transfer, 2018, 98: 155–162
Usman H, Ali H M, Arshad A, et al. An experimental study of PCM based finned and un-finned heat sinks for passive cooling of electronics. Heat Mass Transfer, 2018, 54: 3587–3598
Hassan A, Wahab A, Qasim M A, et al. Thermal management and uniform temperature regulation of photovoltaic modules using hybrid phase change materials-nanofluids system. Renew Energy, 2020, 145: 282–293
Kalbasi R, Afrand M, Alsarraf J, et al. Studies on optimum fins number in PCM-based heat sinks. Energy, 2019, 171: 1088–1099
Xie J, Choo K F, Xiang J, et al. Characterization of natural convection in a PCM-based heat sink with novel conductive structures. Int Commun Heat Mass Transfer, 2019, 108: 104306
Rohsenow W M. A method of correlating heat transfer data for surface boiling of liquids. T ASME, 1952, 74: 969–979
Incropera F P, Dewitt D P. Fundamentals of Heat and Mass Transfer. New York: John Wiley and Sons, 2002
Labuntsov D A. Heat transfer in film condensation of pure steam on vertical surfaces and horizontal tubes. Teploenergetika, 1957, 4: 72–80
Rohsenow W M. Heat transfer and temperature distribution in laminar film condensation. Heat Transf J, 1956, 78: 1645–1648
Chen H, Li Q. Thermal design of a novel heat sink cooled by natural convection with phase transition in the series loop. Sci China Technol Sci, 2018, 61: 1732–1744
Maydanik Y, Pastukhov V, Chernysheva M. Development and investigation of a loop heat pipe with a high heat-transfer capacity. Appl Thermal Eng, 2018, 130: 1052–1061
Blet N, Bertin Y, Ayel V, et al. Experimental analysis of a capillary pumped loop for terrestrial applications with several evaporators in parallel. Appl Thermal Eng, 2016, 93: 1304–1312
Joung W, Gam K, Park K, et al. Transient responses of the flat evaporator loop heat pipe. Int J Heat Mass Transfer, 2013, 57: 131–141
Hong S, Wang S, Zhang Z. Multiple orientations research on heat transfer performances of ultra-thin loop heat pipes with different evaporator structures. Int J Heat Mass Transfer, 2016, 98: 415–425
Zhu K, Li X, Li H, et al. Experimental and theoretical study of a novel loop heat pipe. Appl Thermal Eng, 2018, 130: 354–362
Author information
Authors and Affiliations
Corresponding author
Additional information
This work was supported by the National Natural Science Foundation of China (Grant No. 51225602).
Rights and permissions
About this article
Cite this article
Chen, H., Li, Q. Experimental study of a novel heat sink for distribution level static synchronous compensator cooling. Sci. China Technol. Sci. 63, 1764–1775 (2020). https://doi.org/10.1007/s11431-020-1601-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11431-020-1601-1