Science China Technological Sciences

, Volume 61, Issue 4, pp 522–534 | Cite as

Tool wear performance and surface integrity studies for milling DD5 Ni-based single crystal superalloy

Article
  • 47 Downloads

Abstract

Based on the results of slot milling experiments on the DD5 Ni-based single crystal superalloy (001) crystal plane along the [110] crystal direction, in this paper, efforts were devoted to investigate the tool wear process, wear mechanism and failure modes of the physical vapor deposition (PVD)-AlTiN and TiAlN coated tools under dry milling and water-based minimum quantity lubrication (MQL) conditions. The scanning electron microscope (SEM) morphological observation and energy dispersive X-ray spectroscopy (EDX) elements analysis methods were adopted. Moreover, under the water-based MQL condition, the surface integrity such as surface roughness, dimensional and shape accuracy, microhardness and microstructure alteration were researched. The results demonstrated that the tool edge severe adhesion with the work material, induced by the high Al content in the PVD-AlTiN coating caused the catastrophic tool tip fracture. In contrast, the PVD-TiAlN tool displayed a steady and uniform minor flank wear, even though the material peeling and slight chipping also occurred in the final stage. In addition, due to the high effective cooling and lubricating actions of the water-based MQL method, the PVD-TiAlN coated tool demonstrated intact tip geometry; consequently it could be repaired and reused even if the failure criterion was attained. Moreover, as the accumulative milling length and the tool wear increased, all indicators of the surface integrity forehand were deteriorated.

Keywords

DD5 tool wear performance coating material cooling method surface integrity 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Jiang L W, Li S S, Wu M L, et al. Effect of dendrite arm spacing and the γ¢ phase size on stress rupture properties of Ni3Al-base single crystal superalloy IC6SX. Sci China Tech Sci, 2010, 53: 1460–1465CrossRefGoogle Scholar
  2. 2.
    le Graverend J B, Jacques A, Cormier J, et al. Creep of a nickelbased single-crystal superalloy during very high-temperature jumps followed by synchrotron X-ray diffraction. Acta Mater, 2015, 84: 65–79CrossRefGoogle Scholar
  3. 3.
    Lopez-Galilea I, Koßmann J, Kostka A, et al. The thermal stability of topologically close-packed phases in the single-crystal Ni-base superalloy ERBO/1. J Mater Sci, 2016, 51: 2653–2664CrossRefGoogle Scholar
  4. 4.
    M’Saoubi R, Axinte D, Soo S L, et al. High performance cutting of advanced aerospace alloys and composite materials. CIRP Ann-Manuf Tech, 2015, 64: 557–580CrossRefGoogle Scholar
  5. 5.
    Jafarian F, Amirabadi H, Sadri J, et al. Simultaneous optimizing residual stress and surface roughness in turning of inconel718 superalloy. Mater Manuf Process, 2013, 29: 337–343CrossRefGoogle Scholar
  6. 6.
    Zhou J M, Bushlya V, Peng R L, et al. Effects of tool wear on subsurface deformation of nickel-based superalloy. Procedia Eng, 2011, 19: 407–413CrossRefGoogle Scholar
  7. 7.
    Herbert C R J, Kwong J, Kong M C, et al. An evaluation of the evolution of workpiece surface integrity in hole making operations for a nickel-based superalloy. J Mater Process Tech, 2012, 212: 1723–1730CrossRefGoogle Scholar
  8. 8.
    Jin D, Liu Z. Effect of cutting speed on surface integrity and chip morphology in high-speed machining of PM nickel-based superalloy FGH95. Int J Adv Manuf Tech, 2012, 60: 893–899CrossRefGoogle Scholar
  9. 9.
    Cantero J L, Díaz-Álvarez J, Miguélez M H, et al. Analysis of tool wear patterns in finishing turning of Inconel 718. Wear, 2013, 297: 885–894CrossRefGoogle Scholar
  10. 10.
    Devillez A, Schneider F, Dominiak S, et al. Cutting forces and wear in dry machining of Inconel 718 with coated carbide tools. Wear, 2007, 262: 931–942CrossRefGoogle Scholar
  11. 11.
    Najiha M S, Rahman M M. Experimental investigation of flank wear in end milling of aluminum alloy with water-based TiO2 nanofluid lubricant in minimum quantity lubrication technique. Int J Adv Manuf Tech, 2016, 86: 2527–2537CrossRefGoogle Scholar
  12. 12.
    Wang C D, Chen M, An Q L, et al. Tool wear performance in face milling Inconel 182 using minimum quantity lubrication with different nozzle positions. Int J Precis Eng Manuf, 2014, 15: 557–565CrossRefGoogle Scholar
  13. 13.
    Zhu D, Zhang X, Ding H. Tool wear characteristics in machining of nickel-based superalloys. Int J Mach Tool Manu, 2013, 64: 60–77CrossRefGoogle Scholar
  14. 14.
    Thakur A, Gangopadhyay S. State-of-the-art in surface integrity in machining of nickel-based super alloys. Int J Mach Tool Manu, 2016, 100: 25–54CrossRefGoogle Scholar
  15. 15.
    Li Q, Gong Y D, Cai M, et al. Research on surface integrity in milling Inconel718 superalloy. Int J Adv Manuf Tech, 2017: 1–15Google Scholar
  16. 16.
    Ucun, Aslantas K, Bedir F. An experimental investigation of the effect of coating material on tool wear in micro milling of Inconel 718 super alloy. Wear, 2013, 300: 8–19CrossRefGoogle Scholar
  17. 17.
    Imran M, Mativenga P T, Gholinia A, et al. Comparison of tool wear mechanisms and surface integrity for dry and wet micro-drilling of nickel-base superalloys. Int J Mach Tool Manu, 2014, 76: 49–60CrossRefGoogle Scholar
  18. 18.
    Xu X, Yu Y, Huang H. Mechanisms of abrasive wear in the grinding of titanium (TC4) and nickel (K417) alloys. Wear, 2003, 255: 1421–1426CrossRefGoogle Scholar
  19. 19.
    Sharma A K, Tiwari A K, Dixit A R. Effects of minimum quantity lubrication (MQL) in machining processes using conventional and nanofluid based cutting fluids: A comprehensive review. J Clean Prod, 2016, 127: 1–18CrossRefGoogle Scholar
  20. 20.
    Zhang S, Li J F, Wang Y W. Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions. J Clean Prod, 2012, 32: 81–87CrossRefGoogle Scholar
  21. 21.
    Bhowmick S, Alpas A T. Minimum quantity lubrication drilling of aluminium-silicon alloys in water using diamond-like carbon coated drills. Int J Mach Tool Manu, 2008, 48: 1429–1443CrossRefGoogle Scholar
  22. 22.
    Hadad M, Sadeghi B. Minimum quantity lubrication-MQL turning of AISI 4140 steel alloy. J Clean Prod, 2013, 54: 332–343CrossRefGoogle Scholar
  23. 23.
    Hadad M. An experimental investigation of the effects of machining parameters on environmentally friendly grinding process. J Clean Prod, 2015, 108: 217–231CrossRefGoogle Scholar
  24. 24.
    Mao C, Tang X, Zou H, et al. Experimental investigation of surface quality for minimum quantity oil-water lubrication grinding. Int J Adv Manuf Tech, 2012, 59: 93–100CrossRefGoogle Scholar
  25. 25.
    Lin H, Wang C, Yuan Y, et al. Tool wear in Ti-6Al-4V alloy turning under oils on water cooling comparing with cryogenic air mixed with minimal quantity lubrication. Int J Adv Manuf Tech, 2015, 81: 87–101CrossRefGoogle Scholar
  26. 26.
    Jin D, Liu Z. Damage of the machined surface and subsurface in orthogonal milling of FGH95 superalloy. Int J Adv Manuf Tech, 2013, 68: 1573–1581CrossRefGoogle Scholar
  27. 27.
    Motorcu A R, Kuş A, Durgun I. The evaluation of the effects of control factors on surface roughness in the drilling of Waspaloy superalloy. Measurement, 2014, 58: 394–408CrossRefGoogle Scholar
  28. 28.
    Li W, Guo Y B, Barkey M E, et al. Effect tool wear during end milling on the surface integrity and fatigue life of Inconel 718. Procedia CIRP, 2014, 14: 546–551CrossRefGoogle Scholar
  29. 29.
    Sharman A R C, Hughes J I, Ridgway K. The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718™. J Mater Process Tech, 2015, 216: 123–132CrossRefGoogle Scholar
  30. 30.
    Gao Q, Gong Y, Zhou Y, et al. Experimental study of micro-milling mechanism and surface quality of a nickel-based single crystal superalloy. J Mech Sci Tech, 2015, 21: 192–214Google Scholar
  31. 31.
    Zhu Z X, Gong Y D, Zhou Y G, et al. Molecular dynamics simulation of single crystal Nickel nanometric machining. Sci China Tech Sci, 2016, 59: 867–875CrossRefGoogle Scholar

Copyright information

© Science China Press and Springer-Verlag GmbH Germany, part of Springer Nature 2017

Authors and Affiliations

  • YaDong Gong
    • 1
  • Qiang Li
    • 1
  • JinGuo Li
    • 2
  • Yin Liu
    • 1
  • Yao Sun
    • 1
  1. 1.School of Mechanical Engineering & AutomationNortheastern UniversityShenyangChina
  2. 2.Institute of Metal ResearchChinese Academy of SciencesShenyangChina

Personalised recommendations