Abstract
Solid waste (SW) has become a problem hindering the economic and social development. Achieving the full green cycle from raw material to production of recycled building bricks (RBB) using SW is the focus of future research. In this paper, the research results of RBB manufacturing using SW in recent years are reviewed. According to the consolidation principle of RBB, the effects of different types of SW on the physicochemical properties and microstructure of RBB are summarized based on the recycled unsintered brick (RUSB) and recycled sintered brick (RSB). By comparing and evaluating the two consolidation methods, it is proposed that RSB has good practicality due to its higher SW utilization rate, higher strength, and faster consolidation speed. Furthermore, the difference between MWS and conventional sintering (CS) is analyzed, and the research on the application of MWS in SW-RBB manufacturing in recent years is reviewed in detail. It is pointed out that microwave sintering (MWS) technology can solve many drawbacks in traditional sintering technology and has great prospects in manufacturing SW-RBB due to the low energy consumption, low pollution, and high efficiency. Finally, the shortcomings and possible challenges in the current research on manufacturing SW-RBB using MWS technology are discussed, which provides guidance for the future development of SW-RBB manufacturing.
Similar content being viewed by others
Data availability
Not applicable.
References
Adazabra AN, Viruthagiri G, Shanmugam N (2017) Infrared analysis of clay bricks incorporated with spent shea waste from the shea butter industry. J Environ Manag 191:66–74. https://doi.org/10.1016/j.jenvman.2017.01.006
Al-Fakih A, Mohammed BS, Liew MS, Nikbakht E (2019) Incorporation of waste materials in the manufacture of masonry bricks: an update review. J Build Eng 21:37–54. https://doi.org/10.1016/j.jobe.2018.09.023
Al-Sinan MA, Bubshait AA (2022) Using plastic sand as a construction material toward a circular economy: a review. Sustainability 14. https://doi.org/10.3390/su14116446
Andiç-Çakır Ö, Son AE, Sürmelioğlu S et al (2021) Improvement of traditional clay bricks’ thermal insulation characteristics by using waste materials. Case Stud Constr Mater 15. https://doi.org/10.1016/j.cscm.2021.e00560
Arsenovic M, Radojevic Z, Stankovic S (2012) Removal of toxic metals from industrial sludge by fixing in brick structure. Constr Build Mater 37:7–14. https://doi.org/10.1016/j.conbuildmat.2012.07.002
Ashour T, Korjenic A, Korjenic S, Wu W (2015) Thermal conductivity of unfired earth bricks reinforced by agricultural wastes with cement and gypsum. Energy Build 104:139–146. https://doi.org/10.1016/j.enbuild.2015.07.016
C. ASTM, 67–08 (2003) Standard test methods for sampling and testing brick and structural clay tile. PA Am. Soc. Test Mater, Philadelphia
Bai M, Xiao J, Gao Q, Shen J (2023) Utilization of construction spoil and recycled powder in fired bricks. Case Stud Constr Mater 18:e02024. https://doi.org/10.1016/j.cscm.2023.e02024
Bai XD, Cheng WC, Sheil BB, Li G (2021) Pipejacking clogging detection in soft alluvial deposits using machine learning algorithms. Tunn Undergr Space Technol 113. https://doi.org/10.1016/j.tust.2021.103908
Barbieri L, Andreola F, Lancellotti I, Taurino R (2013) Management of agricultural biomass wastes: preliminary study on characterization and valorisation in clay matrix bricks. Waste Manag 33:2307–2315. https://doi.org/10.1016/j.wasman.2013.03.014
Batchelor AR, Buttress AJ, Jones DA et al (2017) Towards large scale microwave treatment of ores: Part 2 – metallurgical testing. Miner Eng 111:5–24. https://doi.org/10.1016/j.mineng.2017.05.003
Benavente R, Salvador MD, Centeno A et al (2020) Study of microwave heating effect in the behaviour of graphene as second phase in ceramic composites. Materials 13:13–16. https://doi.org/10.3390/ma13051119
Bernal SA, Rodrı ED, Provis JL, Delvasto S (2012) Activation of metakaolin / slag blends using alkaline solutions based on chemically modified silica fume and rice husk ash. 99–108. https://doi.org/10.1007/s12649-011-9093-3
Beshah DA, Tiruye GA, Mekonnen YS (2021) Characterization and recycling of textile sludge for energy-efficient brick production in Ethiopia. Environ Sci Pollut Res 28:16272–16281. https://doi.org/10.1007/s11356-020-11878-7
Bilgin N, Yeprem HA, Arslan S et al (2012) Use of waste marble powder in brick industry. Constr Build Mater 29:449–457. https://doi.org/10.1016/j.conbuildmat.2011.10.011
Bories C, Aouba L, Vedrenne E, Vilarem G (2015) Fired clay bricks using agricultural biomass wastes: study and characterization. Constr Build Mater 91:158–163. https://doi.org/10.1016/j.conbuildmat.2015.05.006
Chang CC, Li R (2019) Agricultural waste. Water Environ Res 91:1150–1167. https://doi.org/10.1002/wer.1211
Chen G, Chen J, Guo S et al (2012) Dissociation behavior and structural of ilmenite ore by microwave irradiation. Appl Surf Sci 258:4826–4829. https://doi.org/10.1016/j.apsusc.2011.12.121
Chen HM, Zheng CR, Tu C, Shen ZG (2000) Chemical methods and phytoremediation of soil contaminated with heavy metals. Chemosphere 41(1–2):229–234. https://doi.org/10.1016/S0045-6535(99)00415-4
Chen Y, Yang F, Yu S (2018) The diffusion effect of MSW recycling https://doi.org/10.3390/su10010040
Cheng J, Shao Z, Xu T et al (2022) The advantages of microwave in using engineering spoil to sinter bricks. J Build Eng 57:104940. https://doi.org/10.1016/j.jobe.2022.104940
Chin WQ, Lee YH, Amran M et al (2022) A sustainable reuse of agro-industrial wastes into green cement bricks. Materials 15. https://doi.org/10.3390/ma15051713
Cudjoe D, Wang H, Zhu B (2021) Assessment of the potential energy and environmental benefits of solid waste recycling in China. J Environ Manag 295:113072. https://doi.org/10.1016/j.jenvman.2021.113072
De Silva GHMJS, Perera BVA (2018) Effect of waste rice husk ash (RHA) on structural, thermal and acoustic properties of fired clay bricks. J Build Eng 18:252–259. https://doi.org/10.1016/j.jobe.2018.03.019
Doğan-Sağlamtimur N, Bilgil A, Szechyńska-Hebda M et al (2021) Eco-friendly fired brick produced from industrial ash and natural clay: a study of waste reuse. Materials 14:1–15. https://doi.org/10.3390/ma14040877
El-Yahyaoui A, Manssouri I, Noureddine O, et al (2022) Physical and mechanical properties of unfired clay bricks with saw palmetto fibers additive as a construction material. Materials Today: Proceedings. https://doi.org/10.1016/j.matpr.2022.09.487
Faria KCP, Gurgel RF, Holanda JNF (2012) Recycling of sugarcane bagasse ash waste in the production of clay bricks. J Environ Manag 101:7–12. https://doi.org/10.1016/j.jenvman.2012.01.032
Ferreira WL, Reis EL, Lima RMF (2015) Incorporation of residues from the minero-metallurgical industry in the production of clayelime brick. J Clean Prod 87:683–691. https://doi.org/10.1016/j.jclepro.2014.09.013
Fořt J, Černý R (2020) Transition to circular economy in the construction industry: environmental aspects of waste brick recycling scenarios. Waste Manag 118:510–520. https://doi.org/10.1016/j.wasman.2020.09.004
Gao Q, Xiao J, Shen J et al (2023) Properties of super-thin layer mortar with recycled brick fines for sintered perforated block masonry. Case Stud Constr Mater 18:e02015. https://doi.org/10.1016/j.cscm.2023.e02015
Gavali HR, Ralegaonkar RV (2020) Design development of sustainable alkali-activated bricks. J Build Eng 30:101302. https://doi.org/10.1016/j.jobe.2020.101302
Gencel O, Kizinievic O, Erdogmus E et al (2022) Manufacturing of fired bricks derived from wastes: utilization of water treatment sludge and concrete demolition waste. Arch Civ Mech Eng 22:1–16. https://doi.org/10.1007/s43452-022-00396-7
Gencel O, Munir MJ, Kazmi SMS et al (2021) Recycling industrial slags in production of fired clay bricks for sustainable manufacturing. Ceram Int 47:30425–30438. https://doi.org/10.1016/j.ceramint.2021.07.222
Ghorbani M, Dahrazma B, Fazlolah S, Yousofizinsaz G (2021) A comparative study on physicochemical properties of environmentally-friendly lightweight bricks having potato peel powder and sour orange leaf. Constr Build Mater 276:121937. https://doi.org/10.1016/j.conbuildmat.2020.121937
Girondi GD, Marvila MM, Azevedo ARGD et al (2020) Recycling potential of powdered cigarette waste in the development of ceramic materials. J Mater Cycles Waste Manag. https://doi.org/10.1007/s10163-020-01058-7
Giusti L (2009) A review of waste management practices and their impact on human health. Waste Manag 29:2227–2239. https://doi.org/10.1016/j.wasman.2009.03.028
González-Cavieres L, Pérez-Won M, Tabilo-Munizaga G et al (2021) Advances in vacuum microwave drying (VMD) systems for food products. Trends Food Sci Technol 116:626–638. https://doi.org/10.1016/j.tifs.2021.08.005
Guo C, Kong J, Wang Z et al (2022) Study on preparation and properties of sintered brick from multi-source solid waste. Appl Sci 12. https://doi.org/10.3390/app121910181
Hafez AI, Khedr MMA, Osman RM et al (2020) A comparative investigation of the unit cost for the preparation of modified sand and clay bricks from rice husk waste. J Build Eng 32:101765. https://doi.org/10.1016/j.jobe.2020.101765
Hafez RDA, Tayeh BA, Abd- Al Ftah RO (2022) Development and evaluation of green fired clay bricks using industrial and agricultural wastes. Case Stud Constr Mater 17:e01391. https://doi.org/10.1016/j.cscm.2022.e01391
Hale SE, Roque AJ, Okkenhaug G et al (2021) The Reuse of Excavated Soils from Construction and Demolition Projects: Limitations and Possibilities. Sustainability 13:6083. https://doi.org/10.3390/su13116083
Hao Y, Guo X, Yao X et al (2022) Using Chinese coal gangue as an ecological aggregate and its modification: a review. Materials 15:1–27. https://doi.org/10.3390/ma15134495
Haque KE (1999) Microwave energy for mineral treatment processes - a brief review. Int J Miner Process 57:1–24. https://doi.org/10.1016/s0301-7516(99)00009-5
Heniegal AM, Ramadan MA, Naguib A, Agwa IS (2020) Journal P Case studies in construction materials e00397. https://doi.org/10.1016/j.cscm.2020.e00397
Hou Y, Xiao J, Shen J, Gao Q (2022) Effects of distiller’s grains and seawater on properties of sintered brick made from construction spoil. J Build Eng 62:105391. https://doi.org/10.1016/j.jobe.2022.105391
Houben H, Guillaud H (1994) Earth construction: a comprehensive guide. Habitat Int 19:643–644
Huang T, Kou S, Liu D et al (2022) Evaluation of the Techno-Economic Feasibility for Excavated Soil Recycling in Shenzhen, China. Sustainability 14:3028. https://doi.org/10.3390/su14053028
Huang TY, Chiueh PT, Lo SL (2017) Life-cycle environmental and cost impacts of reusing fly ash. Resour Conserv Recycl 123:255–260. https://doi.org/10.1016/j.resconrec.2016.07.001
Huber F, Blasenbauer D, Mallow O et al (2016) Thermal co-treatment of combustible hazardous waste and waste incineration fly ash in a rotary kiln. Waste Manag 58:181–190. https://doi.org/10.1016/j.wasman.2016.09.013
Jankus B, Nemes R, Jankus B, Nemes R (2019) Accepted manuscript https://doi.org/10.1016/j.jclepro.2019.04.357
Johnson LJ, Daniel DE, Abeele WV (1978) Effects from past solid waste disposal practices. Environ Health Perspect 27:215–221. https://doi.org/10.2307/3428881
Jones DA, Lelyveld TP, Mavrofidis SD et al (2002) Microwave heating applications in environmental engineering - a review. Resour Conserv Recycl 34:75–90. https://doi.org/10.1016/S0921-3449(01)00088-X
Kazmi SMS, Abbas S, Saleem MA et al (2016) Manufacturing of sustainable clay bricks: utilization of waste sugarcane bagasse and rice husk ashes. Constr Build Mater 120:29–41. https://doi.org/10.1016/j.conbuildmat.2016.05.084
Khanoranga KS (2019) Phytomonitoring of air pollution around brick kilns in Balochistan province Pakistan through air pollution index and metal accumulation index. J Clean Prod 229:727–738. https://doi.org/10.1016/j.jclepro.2019.05.050
Khoudja D, Taallah B, Izemmouren O et al (2021) Mechanical and thermophysical properties of raw earth bricks incorporating date palm waste. Constr Build Mater 270:121824. https://doi.org/10.1016/j.conbuildmat.2020.121824
Kizinievi O, Kizinievi V, Pundiene I, Molotokas D (2018) ScienceDirect Eco-friendly fired clay brick manufactured with agricultural solid waste 8:0–9. https://doi.org/10.1016/j.acme.2018.03.003
Korpayev S, Bayramov M, Durdyev S et al (2023) Effect of stone wool waste from greenhouse agriculture in brick production. J Build Eng 63:105340. https://doi.org/10.1016/j.jobe.2022.105340
Kumar A, Kumar R, Das V et al (2021a) Assessing the structural efficiency and durability of burnt clay bricks incorporating fly ash and silica fume as additives. Constr Build Mater 310:125233. https://doi.org/10.1016/j.conbuildmat.2021.125233
Kumar S, Zhao M, Zhang H et al (2021b) Distribution, contamination status and source of trace elements in the soil around brick kilns. Chemosphere 263:127882. https://doi.org/10.1016/j.chemosphere.2020.127882
Li H, Liu S, Xu W et al (2020a) The effect of microwave on the crystallization behavior of CMAS system class-ceramic. Materials 13:4555
Li JM, Qiu T (2012) Microwave sintering of Ca 0.6La 0.2667TiO 3 microwave dielectric ceramics. Int J Miner Metall Mater 19:245–251. https://doi.org/10.1007/s12613-012-0546-x
Li M, Zhang J, Li A, Zhou N (2020b) Reutilisation of coal gangue and fly ash as underground backfill materials for surface subsidence control. J Clean Prod 254:120113. https://doi.org/10.1016/j.jclepro.2020.120113
Liang S, Zhang T (2015) Comparing urban solid waste recycling from the viewpoint of urban metabolism based on physical input – output model : a case of Suzhou in China. Waste Manag 32:220–225. https://doi.org/10.1016/j.wasman.2011.08.018
Lin S, Jiang X, Zhao Y, Yan J (2022) Zeolite greenly synthesized from fly ash and its resource utilization: a review. Sci Total Environ 851:158182. https://doi.org/10.1016/j.scitotenv.2022.158182
Liu C, Liu B, Chen X et al (2014) Preparation and modification of alkaline bricks by using industrial residues and calcium stearate. Environ Prog Sustain Energy 33:676–680. https://doi.org/10.1002/ep.12425
Liu HY, Wu HS, Chou CP (2020a) Study on engineering and thermal properties of environment-friendly lightweight brick made from Kinmen oyster shells & sorghum waste. Constr Build Mater 246:118367. https://doi.org/10.1016/j.conbuildmat.2020.118367
Liu L, Cheng X, Miao X et al (2020b) Preparation and characterization of majority solid waste based eco-unburned permeable bricks. Constr Build Mater 259:120400. https://doi.org/10.1016/j.conbuildmat.2020.120400
Liu Q, Singh A, Xiao J et al (2020c) Workability and mechanical properties of mortar containing recycled sand from aerated concrete blocks and sintered clay bricks. Resour Conserv Recycl 157:104728. https://doi.org/10.1016/j.resconrec.2020.104728
Liu Y, Park S, Yi H, Feiock R (2020d) Evaluating the employment impact of recycling performance in Florida. Waste Manag 101:283–290. https://doi.org/10.1016/j.wasman.2019.10.025
Lü C, Ai Y, Yu Q et al (2019) Study on the growth kinetics of Al2O3 columnar crystal in Al2O3 matrix composite ceramics prepared by microwave sintering. J Cryst Growth 507:395–401. https://doi.org/10.1016/j.jcrysgro.2018.11.039
Luo J, Zhong Z, Xu J (2012) Yttrium oxide transparent ceramics by low-temperature microwave sintering. Mater Res Bull 47:4283–4285. https://doi.org/10.1016/j.materresbull.2012.09.017
Lyra GP, De Santis BC, Santos V et al (2022) Microwave fast sintering production of sustainable lightweight aggregates with agroindustrial waste. J Mater Civ Eng 34:1–10. https://doi.org/10.1061/(asce)mt.1943-5533.0004302
Lyra GP, dos Santos V, De Santis BC et al (2019) Reuse of sugarcane bagasse ash to produce a lightweight aggregate using microwave oven sintering. Constr Build Mater 222:222–228. https://doi.org/10.1016/j.conbuildmat.2019.06.150
Mandal AK, Verma HR, Sinha OP (2017) Utilization of aluminum plant’s waste for production of insulation bricks. J Clean Prod 162:949–957. https://doi.org/10.1016/j.jclepro.2017.06.080
Mehta A, Siddique R (2016) An overview of geopolymers derived from industrial by-products. Constr Build Mater 127:183–198. https://doi.org/10.1016/j.conbuildmat.2016.09.136
Mejía JM, Gutiérrez RMD, Montes C (2016) Rice husk ash and spent diatomaceous earth as a source of silica to fabricate a geopolymeric binary binder. J Clean Prod. https://doi.org/10.1016/j.jclepro.2016.01.057
Menezes RR, Souto PM, Kiminami RH (2012) Microwave fast sintering of ceramic materials. Sintering of ceramics - new emerging techniques https://doi.org/10.5772/34181
Migliore M, Talamo C, Paganin G (2020) Construction and demolition waste. Springer Tracts in Civil Engineering 45–76. https://doi.org/10.1007/978-3-030-30318-1_2
Minh Trang NT, Dao Ho NA, Babel S (2021) Reuse of waste sludge from water treatment plants and fly ash for manufacturing of adobe bricks. Chemosphere 284:131367. https://doi.org/10.1016/j.chemosphere.2021.131367
Mohajerani A, Abdul A, Larobina L (2016) A practical proposal for solving the world ’ s cigarette butt problem: recycling in fired clay bricks. Waste Manag. https://doi.org/10.1016/j.wasman.2016.03.012
Monedero E, Hernández JJ, Collado R et al (2021) Evaluation of ashes from agro-industrial biomass as a component for producing construction materials. J Clean Prod 318. https://doi.org/10.1016/j.jclepro.2021.128517
Moraes JCB, Tashima MM, Akasaki JL et al (2017) Effect of sugar cane straw ash ( SCSA ) as solid precursor and the alkaline activator composition on alkali-activated binders based on blast furnace slag (BFS). Constr Build Mater 144:214–224. https://doi.org/10.1016/j.conbuildmat.2017.03.166
Moreno-maroto JM, Nájera P, Cotes-palomino T et al (2019) Manufacturing of lightweight aggregates from biomass fl y ash, beer bagasse, Zn-rich industrial sludge and clay by slow firing. J Environ Manag 246:785–795. https://doi.org/10.1016/j.jenvman.2019.06.059
Morsy MI, Alakeel KA, Ahmed AE et al (2022) Recycling rice straw ash to produce low thermal conductivity and moisture-resistant geopolymer adobe bricks. Saudi J Biol Sci 29:3759–3771. https://doi.org/10.1016/j.sjbs.2022.02.046
Munir MJ, Abbas S, Nehdi ML et al (2018) Development of eco-friendly fired clay bricks incorporating recycled marble powder. J Mater Civ Eng 30:04018069. https://doi.org/10.1061/(asce)mt.1943-5533.0002259
Niyomukiza JB, Nabitaka KC, Kiwanuka M et al (2022) Enhancing properties of unfired clay bricks using palm fronds and palm seeds. Results in Engineering 16:100632. https://doi.org/10.1016/j.rineng.2022.100632
Oghbaei M, Mirzaee O (2010) ChemInform abstract: microwave versus conventional sintering: a review of fundamentals, advantages and applications. ChemInform 41:no-no. https://doi.org/10.1002/chin.201021216
Ozturk S, Sutcu M, Erdogmus E, Gencel O (2019) Influence of tea waste concentration in the physical, mechanical and thermal properties of brick clay mixtures. Constr Build Mater 217:592–599. https://doi.org/10.1016/j.conbuildmat.2019.05.114
Palaniyappan S, Annamalai VE, Ashwinkumaran S et al (2022) Utilization of abrasive industry waste as a substitute material for the production of fireclay brick. J Build Eng 45:103606. https://doi.org/10.1016/j.jobe.2021.103606
Palmiotto M, Fattore E, Paiano V et al (2014) Influence of a municipal solid waste land fi ll in the surrounding environment: toxicological risk and odor nuisance effects. Environ Int 68:16–24. https://doi.org/10.1016/j.envint.2014.03.004
Peng Z, Hwang JY (2015) Microwave-assisted metallurgy. Int Mater Rev 60:30–63. https://doi.org/10.1179/1743280414Y.0000000042
Pérez-villarejo L, Eliche-quesada D, Martín-pascual J, et al (2020) Comparative study of the use of different biomass from olive grove in the manufacture of sustainable ceramic lightweight bricks 231. https://doi.org/10.1016/j.conbuildmat.2019.117103
Porta D, Milani S, Lazzarino AI, et al (2009) Systematic review of epidemiological studies on health effects associated with management of solid waste 14:1–14. https://doi.org/10.1186/1476-069X-8-60
Presenda Á, Salvador MD, Penaranda-Foix FL et al (2017) Effects of microwave sintering in aging resistance of zirconia-based ceramics. Chem Eng Process Process Intensif 122:404–412. https://doi.org/10.1016/j.cep.2017.03.002
Qiu Q, Jiang X, Lv G et al (2018) Adsorption of heavy metal ions using zeolite materials of municipal solid waste incineration fly ash modified by microwave-assisted hydrothermal treatment. Powder Technol 335:156–163. https://doi.org/10.1016/j.powtec.2018.05.003
Quijorna N, Coz A, Andres A, Cheeseman C (2012) Recycling of Waelz slag and waste foundry sand in red clay bricks. Resour Conserv Recycl 65:1–10. https://doi.org/10.1016/j.resconrec.2012.05.004
Quina MJ, Bontempi E, Bogush A et al (2018) Science of the Total Environment Technologies for the management of MSW incineration ashes from gas cleaning: new perspectives on recovery of secondary raw materials and circular economy. Sci Total Environ 635:526–542. https://doi.org/10.1016/j.scitotenv.2018.04.150
Rahman A, Urabe T, Kishimoto N, Mizuhara S (2015) Effects of waste glass additions on quality of textile sludge-based bricks. Environ Technol 36:2443–2450. https://doi.org/10.1080/09593330.2015.1034188
Rethinam S, Aruni AW, Turkmen H (2021) Eco-friendly bioenergy: new approaches for the effective treatment of tannery fleshings. Environ Chall 5:100249. https://doi.org/10.1016/j.envc.2021.100249
Rubia-garcía MDL, Yebra-rodríguez Á, Eliche-quesada D, et al (2012) Assessment of olive mill solid residue (pomace) as an additive in lightweight brick production 36:495–500. https://doi.org/10.1016/j.conbuildmat.2012.06.009
Saltiel C, Datta AK (1999) Heat and mass transfer in microwave processing. Adv Heat Tran 33:1–94
Sarani NA, Kadir AA, Rahim ASA, Mohajerani A (2018) Properties and environmental impact of the mosaic sludge incorporated into fired clay bricks. Constr Build Mater 183:300–310. https://doi.org/10.1016/j.conbuildmat.2018.06.171
Sarkar R, Singh N, Das SK (2007) Effect of addition of pond ash and fly ash on properties of ash-clay burnt bricks. Waste Manag Res 25:566–571. https://doi.org/10.1177/0734242X07080114
Seddik Hassan AM, Abdeen A, Mohamed AS, Elboshy B (2022) Thermal performance analysis of clay brick mixed with sludge and agriculture waste. Constr Build Mater 344:128267. https://doi.org/10.1016/j.conbuildmat.2022.128267
Sen I, Dadush E, Penumadu D (2011) Microwave-assisted foaming of expandable polystyrene beads. J Cell Plast 47:65–79. https://doi.org/10.1177/0021955X10385047
Senthil R, Kavukcu SB, Çakır S et al (2022) Utilization of various solid leather wastes for the production of blended bricks. Clean Techn Environ Policy. https://doi.org/10.1007/s10098-022-02295-0
Senthil R, Kavukcu SB, Sinem Ç, Tunçay KA (2023) Efficacy of natural polymer leather sheet with papermill sludge and leather waste: a novel recycling perspective. Clean Techn Environ Policy. https://doi.org/10.1007/s10098-023-02534-y
Sharholy M, Ahmad K (2008) Municipal solid waste management in Indian cities – a review 28:459–467. https://doi.org/10.1016/j.wasman.2007.02.008
Shi H, Ma H, Tian L et al (2020) Effect of microwave curing on metakaolin-quartz-based geopolymer bricks. Constr Build Mater 258:120354. https://doi.org/10.1016/j.conbuildmat.2020.120354
Shirai T, Yasuoka M, Hotta Y et al (2008) Drying behavior of a slip cast body using a microwave heating. J Am Ceram Soc 91:2367–2370. https://doi.org/10.1111/j.1551-2916.2008.02398.x
Shubbar AA, Sadique M, Kot P, Atherton W (2019) Future of clay-based construction materials – a review. Constr Build Mater 210:172–187. https://doi.org/10.1016/j.conbuildmat.2019.03.206
Siqueira FB, Amaral MC, JNF H (2016) Influence of industrial solid waste addition on properties of soil-cement bricks ( Influência da adição de resíduo sólido industrial nas propriedades de tijolos solo-cimento ). Cerâmica 62:237–241
Stuchly SS, Hamid MAK (1972) Physical parameters in microwave heating processes. J Microw Power 7:117–137. https://doi.org/10.1080/00222739.1972.11688831
Sun T (2018) Dielectric loss law of asphalt mixture under the condition of microwave heating. Int J Appl Electromagn Mech 46:313–323. https://doi.org/10.3233/jae-141968
Sutcu M, Alptekin H, Erdogmus E et al (2015) Characteristics of fired clay bricks with waste marble powder addition as building materials. Constr Build Mater 82:1–8. https://doi.org/10.1016/j.conbuildmat.2015.02.055
Taha Y, Benzaazoua M, Mansori M, Hakkou R (2017) Recycling feasibility of glass wastes and calamine processing tailings in fired bricks making. Waste Biomass Valorization 8:1479–1489. https://doi.org/10.1007/s12649-016-9657-3
Taurino R, Ferretti D, Cattani L et al (2019) Lightweight clay bricks manufactured by using locally available wine industry waste. J Build Eng 26:100892. https://doi.org/10.1016/j.jobe.2019.100892
Taurino R, Karamanov A, Rosa R et al (2017) New ceramic materials from MSWI bottom ash obtained by an innovative microwave-assisted sintering process. J Eur Ceram Soc 37:323–331. https://doi.org/10.1016/j.jeurceramsoc.2016.08.011
Ul Haq E, Kunjalukkal Padmanabhan S, Licciulli A (2015) Microwave synthesis of thermal insulating foams from coal derived bottom ash. Fuel Process Technol 130:263–267. https://doi.org/10.1016/j.fuproc.2014.10.017
Vieira CMF, Pinheiro RM, Rodriguez RJS et al (2016) Clay bricks added with effluent sludge from paper industry: technical, economical and environmental benefits. Appl Clay Sci 132–133:753–759. https://doi.org/10.1016/j.clay.2016.07.001
Wang L, Cheng W-C, Xue Z-F et al (2023) Feasibility study of applying electrokinetic technology coupled with enzyme-induced carbonate precipitation treatment to Cu- and Pb-contaminated loess remediation. J Clean Prod 401:136734. https://doi.org/10.1016/j.jclepro.2023.136734
Wang R, Zhang YX (2018) Recycling fresh concrete waste : a review. 1–17. https://doi.org/10.1002/suco.201800057
Wang Z, Dai N, Wang X et al (2020) Early-stage road property improvements of cold recycled asphalt emulsion mixture with microwave technology. J Clean Prod 263:121451. https://doi.org/10.1016/j.jclepro.2020.121451
Wei Q, Gao W, Sui X (2010) Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue. Waste Manag Res 28:944–950. https://doi.org/10.1177/0734242X09351734
Wei W, Shao Z, Qiao R et al (2021b) Recent development of microwave applications for concrete treatment. Constr Build Mater 269:121224. https://doi.org/10.1016/j.conbuildmat.2020.121224
Wei W, Shao Z, Zhang P et al (2021c) Experimental assessment of microwave heating assisted aggregate recycling from dried and saturated concrete. Mater Struct 54:1–14. https://doi.org/10.1617/s11527-021-01741-7
Wei W, Shao Z, Zhang Y et al (2019) Fundamentals and applications of microwave energy in rock and concrete processing – a review. Appl Therm Eng 157:113751. https://doi.org/10.1016/j.applthermaleng.2019.113751
Wei GQ, Wang YS, Hong SX et al (2022) Research Progress of Resource Reutilization of Engineering Excavated Soil. Materials Reports 36(13):20110138–9 (in Chinese)
Wiemes L, Pawlowsky U, Mymrin V (2017) Incorporation of industrial wastes as raw materials in brick’s formulation. J Clean Prod 142:69–77. https://doi.org/10.1016/j.jclepro.2016.06.174
Wu K, Shao Z, Jiang Y et al (2023a) Determination of stiffness of circumferential yielding lining considering the shotcrete hardening property. Rock Mech Rock Eng 56:3023–3036. https://doi.org/10.1007/s00603-022-03122-0
Wu K, Sharifzadeh M, Shao ZS, Zheng XM, Zhao NN, Yang YZ (2023b) Analytical model for soft rock tunnel with large deformation using stiff and yielding lining solutions. Int J Geomech 23:1–12. https://doi.org/10.1061/IJGNAI.GMENG-8483
Wu K, Zheng XM, Zhao NN, Shao ZS (2023c) Effect of compressible layer on time-dependent behaviour of soft-rock large deformation tunnels revealed by mathematical analytical method. Appl Math Model 124:1–20
Xiao J, Shen J, Bai M et al (2021) Reuse of construction spoil in China: current status and future opportunities. J Clean Prod 290:125742. https://doi.org/10.1016/j.jclepro.2020.125742
Xie X, Zhang W, Luan X et al (2022) Thermal performance enhancement of hollow brick by agricultural wastes. Case Stud Constr Mater 16:e01047. https://doi.org/10.1016/j.cscm.2022.e01047
Xie YX, Cheng WC, Wang L et al (2023) Immobilizing copper in loess soil using microbial-induced carbonate precipitation: insights from test tube experiments and one-dimensional soil columns. J Hazard Mater 444:130417. https://doi.org/10.1016/j.jhazmat.2022.130417
Yamuna Rani M, Bhagawan D, Himabindu V et al (2016) Preparation and characterization of green bricks using pharmaceutical industrial wastes. Environ Sci Pollut Res 23:9323–9333. https://doi.org/10.1007/s11356-015-5191-2
Yaras A (2020) Combined effects of paper mill sludge and carbonation sludge on characteristics of fired clay bricks. Constr Build Mater 249:118722. https://doi.org/10.1016/j.conbuildmat.2020.118722
Yaseen N, Irfan-ul-Hassan M, Saeed A-R et al (2022) Sustainable development and performance assessment of clay-based geopolymer bricks incorporating fly ash and sugarcane bagasse ash. J Mater Civ Eng 34:1–16. https://doi.org/10.1061/(asce)mt.1943-5533.0004159
Yuan Y, Shao Z, Qiao R et al (2021a) Quantifying damage evolution within olivine basalt based on crack propagation behavior under microwave irradiation. Int J Damage Mech 30:1617–1641. https://doi.org/10.1177/10567895211017318
Yuan Y, Shao Z, Qiao R et al (2021b) Fracture behavior of concrete coarse aggregates under microwave irradiation influenced by mineral components. Constr Build Mater 286:122944. https://doi.org/10.1016/j.conbuildmat.2021.122944
Yuan Y, Shao Z, Qiao R et al (2022) Crack damage evolution in concrete coarse aggregates under microwave-induced thermal stress. Arch Civ Mech Eng 22:1–23. https://doi.org/10.1007/s43452-022-00419-3
Zaccaron A, de Souza NV, Bernardin AM (2021) Fast drying for the manufacturing of clay ceramics using natural clays. J Build Eng 33:101877. https://doi.org/10.1016/j.jobe.2020.101877
Zeng Y, Chen R, Yang M et al (2019) Fast fabrication of high quality Li2TiO3–Li4SiO4 biphasic ceramic pebbles by microwave sintering: in comparison with conventional sintering. Ceram Int 45:19022–19026. https://doi.org/10.1016/j.ceramint.2019.06.143
Zhang L (2013) Production of bricks from waste materials - a review. Constr Build Mater 47:643–655. https://doi.org/10.1016/j.conbuildmat.2013.05.043
Zhang S, Dong R, Wang M et al (2020) Synthesis mechanisms on waste poplar fiber lightweight biomass bricks. J Clean Prod 246:118981. https://doi.org/10.1016/j.jclepro.2019.118981
Zhao H, Gou H (2021) Unfired bricks prepared with red mud and calcium sulfoaluminate cement: properties and environmental impact. J Build Eng 38:102238. https://doi.org/10.1016/j.jobe.2021.102238
Zhao Y, Liang NX, Chen H, Li Y (2020) Preparation and properties of sintering red mud unburned road brick using orthogonal experiments. Constr Build Mater 238:117739. https://doi.org/10.1016/j.conbuildmat.2019.117739
Zhu M, Wang H, Liu LL et al (2017) Preparation and characterization of permeable bricks from gangue and tailings. Constr Build Mater 148:484–491. https://doi.org/10.1016/j.conbuildmat.2017.05.096
Funding
This work was supported by the National Natural Science Foundation of China (No.11872287), the Found of Shaanxi Key Research and Development Program (No.2019ZDLGY01-10) and the Natural Science Basic Research Program of Shaanxi (Program No. 2023-JC-QN-0451).
Author information
Authors and Affiliations
Contributions
JC: conceptualization, methodology, investigation, formal analysis, data curation, writing (original draft), and validation
ZS: funding acquisition, project administration, writing (editing), and validation
YW: investigation
WW: conceptualization and methodology
YY: investigation
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Responsible Editor: Philippe Garrigues
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Cheng, ., Shao, Z., Wang, Y. et al. The current status and future of solid waste recycled building bricks. Environ Sci Pollut Res 30, 105119–105148 (2023). https://doi.org/10.1007/s11356-023-29902-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-023-29902-x