Abstract
Large amounts of water-based drilling cuttings (WDC) would be generated during the drilling of shale gas wells, which would occupy land resources and pose significant threat to soil and groundwater environment. The aim of this study was to assess the feasibility of using WDC as a replacement of natural clay to prepare sintered bricks. To determine the optimum preparation condition, the weight loss on ignition, bulk density, water absorption, and compressive strength of the samples were tested. Meanwhile, the environmental performance of the final products was evaluated and micro-analysis was conducted via X-ray diffraction and scanning electron microscopy. The results showed that using WDC to manufacture sintered bricks was technically feasible, but the physical mechanical performance would significantly decrease with the increase of the replacement ratio because of the presence of less silica and excessive calcium. The addition of waste glass and fly ash could promote the generation of molten glassy phase and form the crystal particle bonding structure, which would contribute to the physical-mechanical performance of WDC sintered bricks. Some mineral components in raw materials decomposed and formed minerals with better thermal stability during the sintering process. Under the optimum preparation conditions (mass ratio of WDC: waste glass: fly ash at 40:20:40, sintering temperature at 900 °C, and insulation time at 2 h), the physical-mechanical and environmental performance of WDC sintered bricks could meet the requirements of corresponding Chinese standards and ASTM standards. Thus, in this study, an effective solution to recycle WDC from shale gas development is provided.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Data availability
All data generated or analyzed during this study are included in this published article (and its supplementary information files).
References
Ayati B, Molineux C, Newport D, Cheeseman C (2019) Manufacture and performance of lightweight aggregate from waste drill cuttings. J Clean Prod 208:252–260. https://doi.org/10.1016/j.jclepro.2018.10.134
Ball AS, Stewart RJ, Schliephake K (2012) A review of the current options for the treatment and safe disposal of drill cuttings. Waste Manag Res 30(5):457–473. https://doi.org/10.1177/0734242X11419892
Chen C, Wu H (2018) Lightweight bricks manufactured from ground soil, textile sludge, and coal ash. Environ Technol 39(11):1359–1367. https://doi.org/10.1080/09593330.2017.1329353
Chen CY, Lan GS, Tuan WH (2000) Preparation of mullite by the reaction sintering of kaolinite and alumina. J Eur Ceram Soc 20:2519–2525. https://doi.org/10.1016/10.1016/S0955-2219(00)00125-4
Chen Y, Zhang Y, Chen T, Zhao Y, Bao S (2011) Preparation of eco-friendly construction bricks from hematite tailings. Constr Build Mater 25(4):2107–2111. https://doi.org/10.1016/j.conbuildmat.2010.11.025
Chidiac SE, Federico LM (2007) Effects of waste glass additions on the properties and durability of fired clay brickThis article is one of a selection of papers published in this Special Issue on Masonry. Can J Civ Eng 34(11):1458–1466. https://doi.org/10.1139/L07-120
Cultrone G, Sebastian E (2009) Fly ash addition in clayey materials to improve the quality of solid bricks. Constr Build Mater 23(2):1178–1184. https://doi.org/10.1016/j.conbuildmat.2008.07.001
Dai Z, Zhou H, Zhang W, Hu L, Huang Q, Mao L (2019) The improvement in properties and environmental safety of fired clay bricks containing hazardous waste electroplating sludge: The role of Na2SiO3. J Clean Prod 228:1455–1463. https://doi.org/10.1016/j.jclepro.2019.04.274
Demir I (2009) Reuse of waste glass in building brick production. Waste Manag Res 27(6):572–577. https://doi.org/10.1177/0734242X08096528
Elert K, Cultrone G, Navarro CR, Pardo ES (2003) Durability of bricks used in the conservation of historic buildings — influence of composition and microstructure. J Cult Herit 4(2):91–99. https://doi.org/10.1016/S1296-2074(03)00020-7
Hassan HF, Taha R, Al Rawas A, Al Shandoudi B, Al Gheithi K, Al Barami AM (2005) Potential uses of petroleum-contaminated soil in highway construction. Constr Build Mater 19(8):646–652. https://doi.org/10.1016/j.conbuildmat.2005.01.001
Hwang JY, Huang X, Garkida A, Hein A (2006) Waste colored glasses as sintering aid in ceramic tiles production. J Miner Mater Charact Eng 5(2):119–129. https://doi.org/10.4236/jmmce.2006.52008
Kazmi SMS, Abbas S, Nehdi ML, Saleem MA, Munir MJ (2017) Feasibility of Using Waste Glass Sludge in Production of Ecofriendly Clay Bricks. J Mater Civ Eng 29(8):04017056. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001928
Khanpour R, Sheikhi-Kouhsar MR, Esmaeilzadeh F, Mowla D (2014) Removal of contaminants from polluted drilling mud using supercritical carbon dioxide extraction. J Supercrit Fluids 88:1–7. https://doi.org/10.1016/j.supflu.2014.01.004
Kogbara RB (2014) A review of the mechanical and leaching performance of stabilized/solidified contaminated soils. Environ Rev 22:66–86. https://doi.org/10.1139/er-2013-0004
Li XG, Lv Y, Ma BG, Jian SW, Tan HB (2011) Influence of sintering temperature on the characteristics of shale brick containing oil well-derived drilling waste. Environ Sci Pollut Res 18:1617–1622. https://doi.org/10.1007/s11356-011-0526-0
Li R, Zhou Y, Li C, Li S, Huang Z (2019) Recycling of industrial waste iron tailings in porous bricks with low thermal conductivity. Constr Build Mater 213:43–50. https://doi.org/10.1016/j.conbuildmat.2019.04.040
Li B, Wei S, Zhen YW (2020) An effective recycling direction of water-based drilling cuttings and phosphogypsum co-processing in road cushion layer. Environ Sci Pollut Res 27(14):17420–17424. https://doi.org/10.1007/s11356-020-08406-y
Lin KL, Chang CT (2006) Leaching characteristics of slag from the melting treatment of municipal solid waste incinerator ash. J Hazard Mater 135:296–302. https://doi.org/10.1016/j.jhazmat.2005.11.064
Liu D, Wang C, Mei X, Zhang C (2018) Environmental performance, mechanical and microstructure analysis of non-fired bricks containing water-based drilling cuttings of shale gas. Constr Build Mater 183:215–225. https://doi.org/10.1016/j.conbuildmat.2018.06.107
Luo L, Li K, Fu W, Liu C, Yang S (2020) Preparation, characteristics and mechanisms of the composite sintered bricks produced from shale, sewage sludge, coal gangue powder and iron ore tailings. Constr Build Mater 232:117250. https://doi.org/10.1016/j.conbuildmat.2019.117250
Maitra S, Choudhury A, Das HS, Pramanik MJ (2005) Effect of compaction on the kinetics of thermal decomposition of dolomite under non-isothermal condition. J Mater Sci 40(18):4749–4751. https://doi.org/10.1007/s10853-005-0843-0
Mostavi E, Asadi S, Ugochukwu E (2015) Feasibility Study of the Potential Use of Drill Cuttings in Concrete. Procedia Eng 118:1015–1023. https://doi.org/10.1016/j.proeng.2015.08.543
Muñoz Velasco P, Morales Ortíz MP, Mendívil Giró MA, Muñoz Velasco L (2014) Fired clay bricks manufactured by adding wastes as sustainable construction material – A review. Constr Build Mater 63:97–107. https://doi.org/10.1016/j.conbuildmat.2014.03.045
Phonphuak N, Kanyakam S, Chindaprasirt P (2016) Utilization of waste glass to enhance physical–mechanical properties of fired clay brick. J Clean Prod 112:3057–3062. https://doi.org/10.1016/j.jclepro.2015.10.084
Polettini A, Pomi R, Trinci L, Muntoni A, Lo Mastro S (2004) Engineering and environmental properties of thermally treated mixtures containing MSWI fly ash and low-cost additives. Chemosphere 56(10):901–910. https://doi.org/10.1016/j.chemosphere.2004.05.004
Puad HAM, Noor MYM (2004) Behaviors of 323Th, 238U, 228Ra and 226Ra on combustion of crude oil terminal sludge. J Environ Radioact 73(3):289–305. https://doi.org/10.1016/j.jenvrad.2003.10.004
Santisteban JI, Mediavilla R, Lopez-Pamo E, Dabrio CJ, Zapata MBR, García MJG, Castaño S, Martínez-Alfaro PE (2004) Loss on ignition: a qualitative or quantitative method for organic matter and carbonate mineral content in sediments? J Paleolimnol 32(3):287–299. https://doi.org/10.1023/B:JOPL.0000042999.30131.5b
Shi M, Chen X, Fan S, Shen S, Liu T, Huang Z (2018) Fluxing Agents on Ceramification of Composites of MgO-Al2O3-SiO2/Boron Phenolic Resin. J Wuhan Univ Technol-Mater Sci Ed 33(2):381–388. https://doi.org/10.1007/s11595-018-1833-8
Shih PH, Wu ZZ, Chiang HL (2004) Characteristics of bricks made from waste steel slag. Waste Manag 24(10):1043–1047. https://doi.org/10.1016/j.wasman.2004.08.006
Song JG, Wang F, Bai XB, Du DM, Ju YY, Xu MH, Ji GC (2011) Effect of the sintering technology on the properties of fired brick from quartz sands. J Ceram Process Res 12(4):357–360. https://doi.org/10.3724/SP.J.1077.2011.00797
Tuncan A, Tuncan M, Koyuncu H (2010) Use of petroleum-contaminated drilling wastes as sub-base material for road construction. Waste Manag Res 18(5):489–505. https://doi.org/10.1034/j.1399-3070.2000.00135.x
Wang C, Mei X, Zhang C, Liu D, Xu F (2020) Mechanism study on co-processing of water-based drilling cuttings and phosphogypsum in non-autoclaved aerated concrete. Environ Sci Pollut Res 27(18):23364–23368. https://doi.org/10.1007/s11356-020-09029-z
Xu H, Song W, Cao W, Shao G, Lu H, Yang D, Chen D, Zhang R (2017) Utilization of coal gangue for the production of brick. J Mater Cycles Waste Manag 19(3):1270–1278. https://doi.org/10.1007/s10163-016-0521-0
Yariv S (2004) The role of charcoal on DTA curves of organo-clay complexes: an overview. Appl Clay Sci 24:225–236. https://doi.org/10.1016/j.clay.2003.04.002
Yürüyen S, Toplan HÖ (2009) The sintering kinetics of porcelain bodies made from waste glass and fly ash. Ceram Int 35(6):2427–2433. https://doi.org/10.1016/j.ceramint.2009.02.005
Acknowledgements
This work was financially supported by the National Science and Technology Major Project of China (No.2016ZX05040-001) and the Science and Technology Cooperation Project of the CNPC-SWPU Innovation Alliance (No. 2020CX020300).
Funding
The National Science and Technology Major Project of China (No.2016ZX05040-001 and No.2016ZX05062) and the Science and Technology Cooperation Project of the CNPC-SWPU Innovation Alliance (No. 2020CX020300).
Author information
Authors and Affiliations
Contributions
Conceptualization, Wenshi Liu; data curation, Hui Yuan; formal analysis, Lingru Sun; funding acquisition, Zhenzhen Fan; investigation, Hui Yuan; methodology, Zhenzhen Fan; resources, Jing Li; Supervision, Zhenzhen Fan; writing—original draft preparation, Hui Yuan; writing—review and editing, Wenshi Liu and Lingru Sun.
Corresponding author
Ethics declarations
Ethics approval and consent to participate
Not applicable.
Consent for publication
The authors consent for publication.
Competing interests
The authors declare that they have no competing interests.
Additional information
Responsible Editor: Philippe Garrigues
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Liu, W., Yuan, H., Fan, Z. et al. Using water-based drilling cuttings from shale gas development to manufacture sintered bricks: a case study in the southern Sichuan Basin, China. Environ Sci Pollut Res 28, 29379–29393 (2021). https://doi.org/10.1007/s11356-021-12847-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11356-021-12847-4