Skip to main content
SpringerLink
Log in

Investigation on the Residue Gas Inflation Technique for Space Borne Inflatable Boom with Different Folding Patterns

  • Research paper
  • Published:
Experimental Mechanics Aims and scope Submit manuscript

Abstract

Background

The last two decades have seen a growing trend toward the use of inflatable membranes for spaceborne structures. The spaceborne inflatable membrane structures are the promising solution for the compact and lightweight reflector antenna. The inflation technique is used for pressurizing the inflatable membrane structure once the satellite reaches to its predefined orbit.

Objective

The objective of the study is to demonstrate the use of the residue gas inflation technique for the complete deployment of the inflatable thin membrane boom with different folding patterns. The study also aims to find out generalized relation to calculate the safe mass of residue gases to be kept inside spaceborne membrane boom.

Method

The novel analytical relation for the safe mass of residue gases that can be carried for any size of the inflatable boom is established. A comparative study is performed to investigate the effect of variation in a folding pattern on the proposed inflation technique. Experimental, numerical, and analytical approaches were employed for the proposed study.

Result

The results show that the total inflation time is inversely proportional to the mass of the residue gases. Through the comparative study, it has been observed that the change in the inflation time is negligible for different folding patterns with the same mass of residue gas. The result confirms that the safe mass of residue gas is successfully deploying the inflatable boom in the vacuum environmental condition keeping the stresses in the boom in the tolerance limit.

Conclusions

The findings of this research provide insights into a simple and cost-effective design solution for the inflation system along with safe mass of the residue gases which can be used for any size of spaceborne inflatable boom.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

References

  1. Huh Y, Kim D, Lee H (2010) Measurement of mechanical properties of thin film by membrane deflection test. Exp Mech 50:429–435

    Article  Google Scholar 

  2. Thota P, Leifer J, Smith SW, Lumpp JK (2005) Pattern evaluation for in-plane displacement measurement of thin films. Exp Mech 45(1):18–26

    Article  Google Scholar 

  3. Maji AK, Starnes MA (2000) Shape measurement and control of deployable membrane structures. Exp Mech 40(2):154–159

    Article  Google Scholar 

  4. Jenkins CH, Haugen F, Spicher WH (1998) Experimental measurement of wrinkling in membranes undergoing planar deformation. Exp Mech 38(2):147–152

    Article  Google Scholar 

  5. Thomas JC, Wielgosz C (2004) Deflections of highly inflated fabric tubes. Thin-Walled Struct 42(7):1049–1066

    Article  Google Scholar 

  6. Shinde SD, Upadhyay SH (2022) Numerical and experimental study on novel tensioning method for the inflatable paraboloid reflector antenna. Mech Based Des Struct Mach 1:1–18

    Google Scholar 

  7. Chandra M, Kumar S, Chattopadhyaya S, Chatterjee S, Kumar P (2021) A review on developments of deployable membrane-based reflector antennas. Adv Sp Res 68(9):3749–3764

    Article  Google Scholar 

  8. Patiño-Jiménez F, Nahmad-Molinari Y, Moreno-Oliva VI, Santos-García F, Santiago-Alvarado A (2015) Construction and optical testing of inflatable membrane mirror using structured light technique. Int J Photoenergy 1:1–8

    Article  Google Scholar 

  9. Roychowdhury S, DasGupta A (2018) Symmetry breaking during inflation of a toroidal membrane. J Mech Phys Solids 121:328–340

    Article  MathSciNet  Google Scholar 

  10. Li T (2012) Deployment analysis and control of deployable space antenna. Aerosp Sci Technol 18(1):42–47

    Article  Google Scholar 

  11. Szyszkowski W, Glockner PG (1991) Inflatable booms and pneumatic hinges:an application in deployment of satellite sensors. Eng Struct 13(4):357–365

    Article  Google Scholar 

  12. Natori MC, Sakamoto H, Katsumata N, Yamakawa H, Kishimoto N (2015) Conceptual model study using origami for membrane space structures - a perspective of origami-based engineering. Mech Eng Rev 2(1):1–15

    Article  Google Scholar 

  13. Datashvili L, Baier H, Encinar JA, Legay H (2006) Mechanical investigation of a multi-layer reflectarray for Ku-band space antennas. Aerosp Sci Technol 10(7):618–627

    Article  Google Scholar 

  14. Li M, Luo Y, Wu H, Zhu K, Niu Y, Zhao T, Xing J, Kang Z (2017) A prenecking strategy makes stretched membranes with clamped ends wrinkle-free. J Appl Mech Trans ASME 84(6):1–10

    Article  Google Scholar 

  15. Liu M, Shi C, Guo H, Ma X, Liu R, Hu F (2022) Innovative design and optimization of the modular high deployment ratio two-dimensional planar antenna mechanism. Mech Mach Theory 174:1–33

    Article  Google Scholar 

  16. Xiao H, Lu S, Ding X (2018) Tension cable distribution of a membrane antenna frame based on stiffness analysis of the equivalent 4-SPS-S parallel mechanism. Mech Mach Theory 124:133–149

    Article  Google Scholar 

  17. Chen WJ, Fu GY, Gong JH, He YL, Dong SL (2002) Dynamic deployment simulation for pantographic deployable masts. Mech Struct Mach 30(2):249–277

    Article  Google Scholar 

  18. Schenk M, Viquerat AD, Seffen KA, Guest SD (2014) Review of inflatable booms for deployable space structures: packing and rigidization. J Spacecr Rockets 51(3):762–778

    Article  Google Scholar 

  19. Roe LA (2000) Inflation systems for near-term space missions. 41st AIAA Struct, Struct Dyn Mat Conf Exhibit Atlanta, U.S.A. (1):1-4

  20. Wei J, Yu J, Tan H, Wang W, Eriksson A (2020) Design and testing of inflatable gravity-gradient booms in space. CEAS Sp J 12(1):33–41

    Article  Google Scholar 

  21. Chen T, Wen H, Jin D, Hu H (2016) New design and dynamic analysis for deploying rolled booms with thin wall. J Spacecr Rockets 53(1):225–230

    Article  Google Scholar 

  22. Bonin AS, Seffen KA (2014) De-wrinkling of pre-tensioned membranes. Int J Solids Struct 51:3303–3313

    Article  Google Scholar 

  23. Li YL, Lu MY, Tan HF, Tan YQ (2012) A study on wrinkling characteristics and dynamic mechanical behavior of membrane. Acta Mech Sin 28(1):201–210

    Article  MathSciNet  Google Scholar 

  24. Vatankhahghadim B, Damaren CJ (2019) Deployment of a membrane attached to two axially moving beams. J Appl Mech Trans ASME 86(3):1–12

    Article  Google Scholar 

  25. Roychowdhury S, DasGupta A (2018) Inflation mechanics of a membrane reflector supported by an inflated toroidal rim. Eur J Mech A/Solids 67:34–44

    Article  MathSciNet  Google Scholar 

  26. Dharmadasa BY, Mallikarachchi HMYC, Jiménez FL (2018) Characterizing the mechanics of fold-lines in thin kapton membranes. AIAA Spacecr Struct Conf Kissimmee, Florida 1:1–14

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Smart Material and Structures Lab, Mechanical and Industrial Engineering Department, Indian Institute of Technology (IIT) Roorkee, Roorkee, 247667, India

    S. D. Shinde & S. H. Upadhyay

  2. Smart Material and Structures Lab, Mechanical and Industrial Engineering Department, Indian Institute of Technology (IIT) Roorkee, Roorkee, 247 667, India

    S. H. Upadhyay

Authors
  1. S. D. Shinde
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. H. Upadhyay
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. H. Upadhyay.

Ethics declarations

Conflict of interest

The authors have no conflict of interest to declare.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shinde, S.D., Upadhyay, S.H. Investigation on the Residue Gas Inflation Technique for Space Borne Inflatable Boom with Different Folding Patterns. Exp Mech (2024). https://doi.org/10.1007/s11340-024-01072-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s11340-024-01072-y

Keywords

Search

Navigation