Skip to main content
SpringerLink
Log in

Full Field Strain Measurement in Compression and Tensile Split Hopkinson Bar Experiments

  • Published:
Experimental Mechanics Aims and scope Submit manuscript

Abstract

The 3D image correlation technique is used for full field measurement of strain (and strain rate) in compression and tensile split Hopkinson bar experiments using commercial image correlation software and two digital high-speed cameras that provide a synchronized stereo view of the specimen. Using an array of 128 × 80 (compression tests) and 258 × 48 (tensile tests) pixels, the cameras record about 110,000 frames per second. A random dot pattern is applied to the surface of the specimens. The image correlation algorithm uses the dot pattern to define a field of overlapping virtual gage boxes, and the 3-D coordinates of the center of each gage box are determined at each frame. The coordinates are then used for calculating the strains throughout the surface of the specimen. The strains determined with the image correlation method are compared with those determined from analyzing the elastic waves in the bars, and with strains measured with strain gages placed on the specimens. The system is used to study the response of OFE C10100 copper. In compression tests, the image correlation shows a nearly uniform deformation which agrees with the average strain that is determined from the waves in the bars and the strains measured with strain gages that are placed directly on the specimen. In tensile tests, the specimen geometry and properties affect the outcome from the experiment. The full field strain measurement provides means for examining the validity and accuracy of the tests. In tests where the deforming section of the specimen is well defined and the deformation is uniform, the strains measured with the image correlation technique agree with the average strain that is determined from the split Hopkinson bar wave records. If significant deformation is taking place outside the gage section, and when necking develops, the strains determined from the waves are not valid, but the image correlation method provides the accurate full field strain history.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Fig. 22
Fig. 23

Similar content being viewed by others

References

  1. Kolsky H (1949) An investigation of the mechanical properties of materials at very high rates of loading. Proc Phys Soc, London 62-B:676–700.

    Google Scholar 

  2. Gray GT (2000) “Classic Split-Hopkinson Pressure Bar Testing,” ASM Handbook, Vol. 8, Mechanical Testing and Evaluation, ASM International, Materials Park, Ohio, 462–476.

  3. Kahn-Jetter ZL, Chu TC (1990) 3-D displacement measurements using digital image correlation and photogrammetry techniques. Exp Mech 301:10–16.

    Article  Google Scholar 

  4. Helm JD, McNeill SR, Sutton MA (1996) Improved three-dimensional image correlation for surface displacement measurement. Opt Engr 357:1911–1920.

    Article  Google Scholar 

  5. Staab GH, Gilat A (1991) A direct-tension split Hopkinson bar for high strain rate testing. Exp Mech 313:232–235.

    Article  Google Scholar 

Download references

Acknowledgement

The research reported in this paper was supported by the U.S. Air Force SBIR contracts FA8651-05-C-0223 and FA8651-06-C-0123. The technical sponsor is Dr. Joel House and the technical monitor is Mr. Philip Flater. Thanks to Mr. Jeremy Seidt for the useful technical discussions and to Gary Gardner for specimen and adaptor machining.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, The Ohio State University, Columbus, OH, 43210, USA

    A. Gilat (SEM Member) & A. L. Walker (SEM Member)

  2. Trilion Quality Systems, West Conshohocken, PA, 19428, USA

    T. E. Schmidt (SEM Member)

Authors
  1. A. Gilat
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. E. Schmidt
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. L. Walker
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. Gilat.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Gilat, A., Schmidt, T.E. & Walker, A.L. Full Field Strain Measurement in Compression and Tensile Split Hopkinson Bar Experiments. Exp Mech 49, 291–302 (2009). https://doi.org/10.1007/s11340-008-9157-x

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11340-008-9157-x

Keywords

Search

Navigation