Skip to main content
SpringerLink
Log in

Optimization and Comparison of Cd Removal from Aqueous Solutions Using Activated and Non-activated Carbonaceous Adsorbents Prepared by Pyrolysis of Oily Sludge

  • Published:
Water, Air, & Soil Pollution Aims and scope Submit manuscript

Abstract

New porous carbonaceous adsorbents were prepared from an oily sludge generated in a fuel oil storage tank using pyrolysis with and without activation by KOH at 600 °C. The pore characteristics of the activated carbonaceous adsorbent (AC), due to the formation of micropores and mesopores structure, were considerably better than those of non-activated carbonaceous adsorbent (NA). The adsorption of Cd from aqueous solutions on the produced carbonaceous adsorbents was optimized using the Taguchi method. Under optimum conditions, the Cd adsorption efficiency for the NA and AC was obtained to be 77.7 and 98.2 %, respectively. The initial concentration and the adsorbent dose were the most significant factors affecting the removal of Cd by NA and AC, respectively. The adsorption data for the AC were well fitted by the Langmuir, Freundlich, and Redlich-Peterson isotherms models. The regeneration and reuse of the adsorbents in the three cycles of Cd adsorption-desorption were possible. The carbonaceous adsorbents had acceptable efficiency for the removal of Cd from a mine wastewater. Based on the obtained results, the oily sludges available in huge amounts in the petroleum industry proved to be a potential precursor resource for the production of the porous carbonaceous adsorbents, particularly for application in the wastewater treatment.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3

Similar content being viewed by others

References

  • Agrafioti, E., Bouras, G., Kalderis, D., & Diamadopoulos, E. (2013). Biochar production by sewage sludge pyrolysis. Journal of Analytical and Applied Pyrolysis, 101, 72–78.

    Article  CAS  Google Scholar 

  • Al-Futaisi, A., Jamrah, A., Yaghi, B., & Taha, R. (2007). Assessment of alternative management techniques of tank bottom petroleum sludge in Oman. Journal of Hazardous Materials, 141, 557–564.

    Article  CAS  Google Scholar 

  • Andrade, P. F., Azevedo, T. F., Gimenez, I., Filho, A. G., & Barreto, L. S. (2009). Conductive carbon-clay nanocomposites from petroleum oily sludge. Journal of Hazardous Materials, 167, 879–884.

    Article  CAS  Google Scholar 

  • ASTM (2005). Standard test method for ash from petroleum products, PA, USA, ASTM International D 482-87.

  • ASTM (2005). Standard test method for screening of pH in waste, PA, USA, ASTM International D 4980-89.

  • Bandosz, T. J., & Block, K. (2006). Effect of pyrolysis temperature and time on catalytic performance of sewage sludge/industrial sludge-based composite adsorbents. Applied Catalysis B: Environmental, 67, 77–85.

    Article  CAS  Google Scholar 

  • Boualem, T., Debab, A., Martínez de Yuso, A., & Izquierdo, M. T. (2014). Activated carbons obtained from sewage sludge by chemical activation: gas-phase environmental applications. Journal of Environmental Management, 140, 145–151.

    Article  CAS  Google Scholar 

  • Cao, Y., & Pawlowski, A. (2010). Preparation of activated carbons with enhanced adsorption of cationic and anionic dyes from Chinese hickory husk using the Taguchi method. Environment Protection Engineering, 36, 69–86.

    CAS  Google Scholar 

  • Chang, C. Y., Shie, J. L., Lin, J. P., Wu, C. H., Lee, D. J., & Chang, C. F. (2000). Major products obtained from the pyrolysis of oil sludge. Energy and Fuels, 14, 1176–1183.

    Article  CAS  Google Scholar 

  • Chen, X., Jeyaseelan, S., & Graham, N. (2002). Physical and chemical properties study of the activated carbon made from sewage sludge. Waste Management, 22, 755–760.

    Article  CAS  Google Scholar 

  • Deng, H., Li, G., Yang, H., Tang, J., & Tang, J. (2010). Preparation of activated carbons from cotton stalk by microwave assisted KOH and K2CO3 activation. Chemical Engineering Journal, 163, 373–381.

    Article  CAS  Google Scholar 

  • Dias, J. M., Alvim-Ferraz, M. C. M., Almeida, M. F., Rivera-Utrilla, J., & Sánchez-Polo, M. (2007). Waste materials for activated carbon preparation and its use in aqueous-phase treatment: a review. Journal of Environmental Management, 85, 833–846.

    Article  CAS  Google Scholar 

  • Ding, R., Zhang, P., Seredych, M., & Bandosz, T. J. (2012). Removal of antibiotics from water using sewage sludge- and waste oil sludge-derived adsorbents. Water Research, 46, 4081–4090.

    Article  CAS  Google Scholar 

  • Giraldo, L., & Moreno-Piraján, J. C. (2014). Study of adsorption of phenol on activated carbons obtained from eggshells. Journal of Analytical and Applied Pyrolysis, 106, 41–47.

    Article  CAS  Google Scholar 

  • Givianrad, M. H., Rabani, M., Saber-Tehrani, M., Aberoomand-Azar, P., Hosseini Sabzevari, P., & Sau, J. (2011). Preparation and characterization of nanocomposite, silica aerogel, activated carbon and its adsorption properties for Cd (II) ions from aqueous solution. Journal of Saudi Chemical Society, 17(3), 329–335.

    Article  Google Scholar 

  • Hu, G., Li, J., & Zeng, G. (2013). Recent development in the treatment of oily sludge from petroleum industry: a review. Journal of Hazardous Materials, 261, 470–490.

    Article  CAS  Google Scholar 

  • Hydari, S., Sharififard, H., Nabavinia, M., & Parvizi, M. R. (2012). A comparative investigation on removal performances of commercial activated carbon, chitosan biosorbent and chitosan/activated carbon composite for cadmium. Chemical Engineering Journal, 193, 276–282.

    Article  Google Scholar 

  • Karamalidis, A. K., & Voudrias, E. A. (2007). Release of Zn, Ni, Cu, SO4 2- and CrO4 2- as a function of pH from cement-based stabilized/solidified refinery oily sludge and ash from incineration of oily sludge. Journal of Hazardous Materials, 141, 591–606.

    Article  CAS  Google Scholar 

  • Ke, Y., Yang, E. T., Liu, X., Liu, C. L., & Dong, W. S. (2013). Preparation of porous carbons from non-metallic fractions of waste printed circuit boards by chemical and physical activation. New Carbon Materials, 28, 108–114.

    Article  CAS  Google Scholar 

  • Keshari Bhoi S, 2010. Adsorption characteristics of congo red dye onto PAC and GAC based on S/N ratio: A Taguchi approach. Dissertation, National Institute of Technology, Rourkela, India.

  • Kriipsalu, M., Marques, M., & Maastik, A. (2008). Characterization of oily sludge from a wastewater treatment plant flocculation–flotation unit in a petroleum refinery and its treatment implications. Journal of Material Cycles and Waste Management, 10, 79–86.

    Article  CAS  Google Scholar 

  • Kumar Mandal, A., Manab Sarma, P., Singh, B., Jeyaseelan, C. P., Channashettar, V. A., Lal, B., et al. (2011). Bioremediation: a sustainable eco-friendly biotechnological solution for environmental pollution in oil industries. Journal of Sustainable Development and Environment Protection, 1(3), 5–23.

    Google Scholar 

  • Lima, L. S. D., Araujo, M. D. M., Quinaia, S. P., & Migliorine, D. R. (2011). Adsorption modeling of Cr, Cd and Cu on activated carbon of different origins by using fractional factorial design. Chemical Engineering Journal, 166(3), 881–889.

    Article  Google Scholar 

  • Marsh, H., & Rodriguez-Reinoso, F. (2006). Activated carbon (1st ed., pp. 26–27). London: Elsevier.

    Google Scholar 

  • Mazlova, E. A., & Meshcheryakov, S. V. (1999). Ecological characteristics of oil sludges. Chemistry and Technology of Fuels and Oils, 35, 49–53.

    Article  CAS  Google Scholar 

  • Monsalvo, V. M., Mohedano, A. F., & Rodriguez, J. J. (2011). Activated carbons from sewage sludge application to aqueous-phase adsorption of 4-chlorophenol. Desalination, 277, 377–382.

    Article  CAS  Google Scholar 

  • Monser, L., & Adhoum, N. (2009). Tartrazine modified activated carbon for the removal of Pb(II), Cd(II) and Cr(III). Journal of Hazardous Materials, 161, 263–269.

    Article  CAS  Google Scholar 

  • Moreno-Castilla, C., Carrasco-Marin, F., López-Ramón, M. V., & Alvarez-Merino, M. A. (2001). Chemical and physical activation of olive-mill wastewater to produce activated carbons. Carbon, 39, 1415–1420.

    Article  CAS  Google Scholar 

  • Qin, C., Chen, Y., & Gao, J. (2014). Manufacture and characterization of activated carbon from marigold straw (Tagetes erecta L) by H3PO4 chemical activation. Materials Letters, 135, 123–126.

    Article  CAS  Google Scholar 

  • Rafatullah, M., Sulaiman, O., Hashim, R., & Ahmad, A. (2010). Adsorption of methylene blue on low-cost adsorbents: a review. Journal of Hazardous Materials, 177, 70–80.

    Article  CAS  Google Scholar 

  • Rio, S., Faur-Brasquet, C., Coq, L. L., Courcoux, P., & Cloirec, P. L. (2005). Experimental design methodology for the preparation of carbonaceous sorbents from sewage sludge by chemical activation-application to air and water treatments. Chemosphere, 58, 423–437.

    Article  CAS  Google Scholar 

  • Roy, R. (1990). A primer on the Taguchi method (Society of manufacturing engineers 1st ed.). New York: Van Nostrand Reinhold.

    Google Scholar 

  • Ruparelia, J. P., Duttagupta, S. P., Chatterjee, A. K., & Mukherji, S. (2008). Potential of carbon nanomaterials for removal of heavy metals from water. Desalination, 232, 145–155.

    Article  CAS  Google Scholar 

  • Seredych, M., & Bandosz, T. J. (2006). Removal of copper on composite sewage sludge/industrial sludge-based adsorbents: the role of surface chemistry. Journal of Colloid Interface Science, 302, 379–388.

    Article  CAS  Google Scholar 

  • Srivastava, V. C., Deo Mall, I., & Mishra, I. (2008). Optimization of parameters for adsorption of metal ions onto rice husk ash using Taguchi’s experimental design methodology. Chemical Engineering Journal, 140, 136–144.

    Article  CAS  Google Scholar 

  • Suraja, P. V., Yaakob, Z., Binitha, N. N., Triwahyono, S., & Silija, P. P. (2013). Co3O4 doped over SBA 15: excellent adsorbent materials for the removal of methylene blue dye pollutant. Clean Technologies and Environmental Policy, 15, 967–975.

    Article  CAS  Google Scholar 

  • Tan, C., Yaxin, Z., Hongtao, W., Wenjing, L., Zeyu, Z., Yuancheng, Z., & Lulu, R. (2014). Influence of pyrolysis temperature on characteristics and heavy metal adsorptive performance of biochar derived from municipal sewage sludge. Bioresource Technology, 164, 47–54.

    Article  Google Scholar 

  • Youssef, A. M., El-Nabarawy, T., & Samra, S. E. (2004). Sorption properties of chemically-activated carbons 1. Sorption of cadmium (II) ions. Colloids and Surface A: Physicochemical and Engineering Aspects, 235, 153–163.

    Article  CAS  Google Scholar 

  • Zhang, F. S., Nriagu, J. O., & Itoh, H. (2005). Mercury removal from water using activated carbons derived from organic sewage sludge. Water Research, 39, 389–395.

    Article  CAS  Google Scholar 

  • Zolfaghari, G., Esmaili-Sari, A., Anbia, M., Younesi, H., Amir Mahmoodi, S., & Ghafari-Nazari, A. (2011). Taguchi optimization approach for Pb (II) and Hg (II) removal from aqueous solutions using modified mesoporous carbon. Journal of Hazardous Materials, 192, 1046–1055.

    Article  CAS  Google Scholar 

  • Zolgharnein, J., Asanjarani, N., & Shariatmanesh, T. (2013). Taguchi L16 orthogonal array optimization for Cd (II) removal using Carpinus betulus tree leaves: adsorption characterization. International Biodeterioration and Biodegradation, 85, 66–77.

    Article  CAS  Google Scholar 

Download references

Acknowledgments

We are grateful to the oil refinery of Isfahan, Iran, for their support and Dr. Seraji from the Department of Chemistry, Isfahan University of Technology, Isfahan, Iran, for his scientific assistance.

Author information

Authors and Affiliations

  1. Department of Natural Resources, Isfahan University of Technology, Isfahan, Iran

    Shohreh Mohammadi & Nourollah Mirghaffari

Authors
  1. Shohreh Mohammadi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Nourollah Mirghaffari
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Nourollah Mirghaffari.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Mohammadi, S., Mirghaffari, N. Optimization and Comparison of Cd Removal from Aqueous Solutions Using Activated and Non-activated Carbonaceous Adsorbents Prepared by Pyrolysis of Oily Sludge. Water Air Soil Pollut 226, 2237 (2015). https://doi.org/10.1007/s11270-014-2237-x

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s11270-014-2237-x

Keywords

Search

Navigation