Advertisement

Tribology Letters

, 67:41 | Cite as

Densification Behaviour and Wear Performance of Brass-Based Composite Reinforced with SiO2 Nanoparticles: Switchable Water Pump Clutch Application

  • Nianlian LiEmail author
  • Vanessa Bouchart
  • Pierre Chevrier
  • Hongyan Ding
Original Paper
  • 28 Downloads

Abstract

The friction disc and the impeller ring of a switchable water pump (SWP), having a similar principle to that of the wet clutch of an automobile, but it also exhibits a relatively low pressure, a high velocity and temperature. However, SWP possesses an inadequate friction coefficient that has a high tendency to result in the relative slip and severe wear of the counterparts. To acquire such a friction material with an improved friction coefficient and wear resistance to satisfy the new operating condition of SWPs, brass-based composites reinforced by SiO2 nanoparticles were successfully fabricated by the powder sintering in this study, and the influence of the mass fraction of SiO2 nanoparticles on the friction and wear behaviour of the composites was also discussed. The results show that the composite with an appropriate mass friction of SiO2 nanoparticles up to 5 wt% exhibited a homogeneous microstructure. Meanwhile, the friction coefficient was raised to 0.23 with a wear volume reduced to 7.3 × 10− 5 mm3, and the predominant wear mechanism changed from adhesive wear to abrasive wear, due to its enhancement of the densification level and the Vickers micro-hardness.

Keywords

Brass-based nano-composite Wet clutch Densification behaviour Wear mechanism 

Notes

Acknowledgements

This work was supported by PIERBURG PUMP TECHNOLOGY FRANCE SARL.

References

  1. 1.
    Hu, J.B., Wei, C., Li, X.Y.: A uniform cross-speed model of end-face seal ring with spiral grooves for wet clutch. Tribol. Int. 62, 8–17 (2013)CrossRefGoogle Scholar
  2. 2.
    Yang, Y., Lam, R.C.: Theoretical and experimental studies on the interface phenomena during the engagement of automatic transmission clutch. Tribol. Lett 5(1), 57–67 (1998)CrossRefGoogle Scholar
  3. 3.
    Banquy, X., Lowrey, D.D., Belman, N., Min, Y., Mordukhovich, G., Israelachvili, J.N.: Measurement and characterization of “resonance friction” at high sliding speeds in a model automotive wet clutch. Tribol. Lett. 43(2), 185–195 (2011)CrossRefGoogle Scholar
  4. 4.
    Li, M., Khonsari, M.M., McCarthy, D.M., Lundin, J.: On the wear prediction of the paper-based friction material in a wet clutch. Wear 334–335, 56–66 (2015)CrossRefGoogle Scholar
  5. 5.
    Marklund, P., Maki, R., Larsson, R., Hoglund, E., Khonsari, M.M., Jang, J.: Thermal influence on torque transfer of wet clutches in limited slip differential applications. Tribol. Int. 40, 876–884 (2007)CrossRefGoogle Scholar
  6. 6.
    Li, S., Di, Z., Cheng, L., Liu, Z., Piao, J., Huang, D., Zhao, Z., Cui, H., Li, Y.: Surface chemical characterization of steel clutch plate in ATF. Tribol. Int. 102, 319–325 (2016)CrossRefGoogle Scholar
  7. 7.
    Zou, Q., Rao, C., Barber, G., Zhou, B., Wang, Y.: Investigation of surface characteristics and tribological behavior of clutch plate materials. Wear 302, 1378–1383 (2013)CrossRefGoogle Scholar
  8. 8.
    Li, W., Huang, J., Fei, J., Cao, L., Yao, C.: Simulation of the engagement of carbon fabric wet clutch: analytical and experimental comparison. Tribol. Int. 90, 502–508 (2015)CrossRefGoogle Scholar
  9. 9.
    Zhao, E.H., Ma, B., Li, H.Y.: Wear and lubrication behaviors of Cu-Based friction pairs with asperity contacts: numerical and experimental studies. Tribol. Lett. 65(2), 69 (2017)CrossRefGoogle Scholar
  10. 10.
    Li, W., Huang, J., Fei, J., Cao, L., Yao, C.: Study on tribological properties as a function of operating conditions for carbon fabric wet clutch. Tribol. Int. 94, 428–436 (2016)CrossRefGoogle Scholar
  11. 11.
    Bernhardt, J., Albers, A., Ott, S.: Advanced ceramics as friction material in lubricated clutch systems. Tribol. Int. 59, 267–272 (2013)CrossRefGoogle Scholar
  12. 12.
    Gong, T., Yao, P., Xiao, Y., Fan, K., Tan, H., Zhang, Z., Zhao, L., Zhou, H., Deng M.W: Wear map for a copper-based friction clutch material under oil lubrication. Wear 328–329, 270–276 (2015)CrossRefGoogle Scholar
  13. 13.
    Su, Y., Zhang, Y., Song, J., Hu, L.: Tribological behavior and lubrication mechanism of self-lubricating ceramic/metal composites: the effect of matrix type on the friction and wear properties. Wear 372–373, 130–138 (2017)CrossRefGoogle Scholar
  14. 14.
    Ma, W., Lu, J.: Effect of sliding speed on surface modification and tribological behavior of copper–graphite composite. Tribol. Lett. 41, 363–370 (2011)CrossRefGoogle Scholar
  15. 15.
    Xiong, X., Chen, J., Yao, P.P., Li, S., Huang, B.: Friction and wear behaviors and mechanisms of Fe and SiO2 in Cu-based P/M friction materials. Wear 262, 1182–1186 (2007)CrossRefGoogle Scholar
  16. 16.
    Pena-Paras, L., Gao, H., Maldonado-Cortes, D., Vellore, A., García-Pineda, P., Montemayor, O.E., Nava, K.L., Martini, A.: Effects of substrate surface roughness and nano/micro particle additive size on friction and wear in lubricated sliding. Tribol. Int. 119, 88–98 (2018)CrossRefGoogle Scholar
  17. 17.
    Rajkumar, K., Aravindan, S.: Tribological performance of microwave-heat-treated copper–graphite composites. Tribol. Lett. 37, 131–139 (2010)CrossRefGoogle Scholar
  18. 18.
    Li, M., Khonsari, M.M., McCarthy, D.M., Lundin, J.: Parametric analysis for a paper-based wet clutch with groove consideration. Tribol. Lett. 80, 222–233 (2014)CrossRefGoogle Scholar
  19. 19.
    Li, M., Khonsari, M.M., McCarthy, D.M., Lundin, J.: Parametric analysis of wear factors of a wet clutch friction material with different groove patterns. Proc. Inst. Mech. Eng.. 231(8), 1056–1067 (2017)CrossRefGoogle Scholar
  20. 20.
    Reddy, M.P., Ubaid, F., Shakoor, R.A., Parande, G., Manakari, V., Mohamed, A.M.A., Gupta, M.: Effect of reinforcement concentration on the properties of hot extruded Al-Al2O3 composites synthesized through microwave sintering process. Mater. Sci. Eng. A 696, 60–69 (2017)CrossRefGoogle Scholar
  21. 21.
    Sun, C., Song, M., Wang, Z., Chao, Y.H.: Effect of particle size on the microstructures and mechanical properties of SiC-reinforced pure aluminum composites. J. Mater. Eng. Perfor. 20(9), 1606–1612 (2011)CrossRefGoogle Scholar
  22. 22.
    Kumaraguru, S., Kumar, G., Shanmugan, S., Mohan, S., Gnanamuthu, R.M.: Enhanced texture and microhardness of the nickel surface using Bi2O3 particles via electrodeposition technique for engineering application. J. Alloy. Compd. 753, 740–747 (2018)CrossRefGoogle Scholar
  23. 23.
    Jayalakshmi, S., Sankaranarayanan, S., Gupta, M.: Processing and properties of aluminum and magnesium based composites containing amorphous reinforcement: a review. Metals 5(2), 743–762 (2015)CrossRefGoogle Scholar
  24. 24.
    Zhan, Y., Zhang, G.: Friction and wear behavior of copper matrix composites reinforced with SiC and graphite particles. Tribol. Lett. 17(1), 91–98 (2004)CrossRefGoogle Scholar
  25. 25.
    Avcu, E.: The influences of ECAP on the dry sliding wear behavior of AA7075 aluminum alloy. Tribol. Int. 110, 173–184 (2017)CrossRefGoogle Scholar
  26. 26.
    Purcek, G., Yanar, H., Shangina, D.V., Demirtas, M., Bochvar, N.R., Dobatkin, S.V.: Influence of high pressure torsion-induced grain refinement and subsequent aging on tribological properties of Cu-Cr-Zr alloy. J. Alloy. Compd. 742, 325–333 (2018)CrossRefGoogle Scholar
  27. 27.
    Pola, A., Montesano, L., Gelfi, M., La Vecchia, G.M.: Comparison of the sliding wear of a novel Zn alloy with that of two commercial Zn alloys against bearing steel and leaded brass. Wear 368–369, 445–452 (2016)CrossRefGoogle Scholar
  28. 28.
    Su, L., Gao, F., Han, X., Fu, R., Zhang, E.: Tribological behavior of copper–graphite powder third body on copper-based friction materials. Tribol. Lett. 60(2), 1–12 (2015)CrossRefGoogle Scholar
  29. 29.
    Purcek, G., Yanar, H., Saray, O., Karaman, I., Maier, H.J.: Effect of precipitation on mechanical and wear properties of ultrafine-grained Cu–Cr–Zr alloy. Wear 311, 149–158 (2014)CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC, part of Springer Nature 2019

Authors and Affiliations

  • Nianlian Li
    • 1
    • 2
    Email author
  • Vanessa Bouchart
    • 1
  • Pierre Chevrier
    • 1
  • Hongyan Ding
    • 2
  1. 1.Université de Lorraine, CNRS, Arts et Métiers ParisTech, LEM3MetzFrance
  2. 2.Faculty of Mechanical and Material EngineeringHuaiyin Institute of TechnologyHuai’anChina

Personalised recommendations