Skip to main content

Development of a ta-C Wear Resistant Coating with Composite Interlayer for Recording Heads of Magnetic Tape Drives

Tribology Letters volume 46, pages 221–232 (2012)Cite this article

Abstract

The effect of two different surface modification methods on the wear life of the coating of magnetic tape drive heads has been studied. In this research, the heads were coated with 10 nm tetrahedral amorphous carbon (ta-C) film using filtered cathodic vacuum arc (FCVA) technique. The surface of the heads was pretreated by bombarding with energetic carbon ions or by developing a Si–Al–C composite interlayer before deposition of the coating. The coated heads were tested at a real head/tape interface of a tape drive. Surface characterization and tribological behavior of the head coatings with and without surface modification has been studied by transmission electron microscopy (TEM), Auger electron spectroscopy (AES), and scanning electron microscopy (SEM). The results reveal that the ta-C coating without any surface modification is not durable and the coating fails due to delamination. Pre-treating the head surface with energetic carbon ions improves the durability of the coating, especially on the head read/write elements; however, the coating of the head ceramic substrate is still partially delaminated. The application of a Si–Al–C composite interlayer is shown to be able to solve the delamination problem effectively and increase the wear life of the coating up to six times in comparison with the sample pretreated with carbon ions. The formation of strong chemical bonds between the head surface and the overcoat is found to be an important factor in improving the durability of the ta-C head coating.

This is a preview of subscription content, access via your institution.

Access options

Buy single article

Instant access to the full article PDF.

USD 39.95

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14

References

  1. Dee, R.H.: Magnetic tape for data storage: an enduring technology. Proc. IEEE 96(11), 1775–1785 (2008)

    Article  CAS  Google Scholar 

  2. International Magnetic Tape Application and Systems Roadmap, Information Storage Industry Consortium (INSIC), USA (2011)

  3. Wallace, R.L.: The reproduction of magnetically recorded signal. Bell Syst. Technol. J. 30, 1145–1173 (1951)

    Google Scholar 

  4. Thomson, T., Abelmann, L., Groenland, H.: Magnetic data storage: past present and future. In: Azzerboni, B., Asti, G., Pareti, L., Ghidini, M. (eds.) Magnetic nanostructures in modern technology, pp. 237–306. Springer, Netherlands (2008)

    Chapter  Google Scholar 

  5. Spada, F.: Contribution of electrochemical processes to increased head-media spacing in tape drives, reported in INSIC TAPE Program Technical Reviews (www.insic.org/tape.htm). In. Boise, Idaho, USA, (2011), also abstract DT-06 of the 52 nm Annual MMM conference, Tampa, Florida November, 2007

  6. Sourty, E., Sullivan, J.L., De Jong, L.A.M.: Pole tip recession in linear recording heads. IEEE Trans. Magn. 39(3 II), 1859–1861 (2003)

    Article  Google Scholar 

  7. Bhushan, B., Patton, S.T., Sundaram, R., Dey, S.: Pole tip recession studies of hard carbon-coated thin-film tape heads. J. Appl. Phys. 79(8 PART 2B), 5916–5918 (1996)

    Article  CAS  Google Scholar 

  8. Bhushan, B., Theunissen, G.S.A.M., Li, X.: Tribological studies of chromium oxide films for magnetic recording applications. Thin Solid Films 311(1–2), 67–80 (1997)

    Article  CAS  Google Scholar 

  9. Sourty, E., Sullivan, J.L., Bijker, M.D.: Chromium oxide coatings applied to magnetic tape heads for improved wear resistance. Tribol. Int. 36(4–6), 389–396 (2003). doi:10.1016/s0301-679x(02)00214-1

    Article  CAS  Google Scholar 

  10. Theunissen, G.S.A.M.: Wear coatings for magnetic thin film magnetic recording heads. Tribol. Int. 31(9), 519–523 (1998). doi:10.1016/s0301-679x(98)00062-0

    Article  CAS  Google Scholar 

  11. Gupta, B.K., Bhushan, B.: Mechanical and tribological properties of hard carbon coatings for magnetic recording heads. Wear 190(1), 110–122 (1995)

    Article  CAS  Google Scholar 

  12. Scott, W.W., Bhushan, B., Lakshmikumaran, A.V.: Ultrathin diamond-like carbon coatings used for reduction of pole tip recession in magnetic tape heads. J. Appl. Phys. 87(9), 6182–6184 (2000)

    Article  CAS  Google Scholar 

  13. Robertson, J.: Ultrathin carbon coatings for magnetic storage technology. Thin Solid Films 383(1–2), 81–88 (2001)

    Article  CAS  Google Scholar 

  14. Bhatia, C.S., Anders, S., Brown, I.G., Bobb, K., Hsiao, R., Bogy, D.B.: Ultra-thin overcoats for the head/disk interface tribology. J. Tribol. 120(4), 795–799 (1998). doi:10.1115/1.2833781

    Article  CAS  Google Scholar 

  15. Pharr, G.M., Callahan, D.L., McAdams, S.D., Tsui, T.Y., Anders, S., Anders, A., III, J.W.A., Brown, I.G., Bhatia, C.S., Silva, S.R.P., Robertson, J.: Hardness, elastic modulus, and structure of very hard carbon films produced by cathodic-arc deposition with substrate pulse biasing. Appl. Phys. Lett. 68(6), 779–781 (1996)

    Google Scholar 

  16. Robertson, J.: Requirements of ultrathin carbon coatings for magnetic storage technology. Tribol. Int. 36(4–6), 405–415 (2003). doi:10.1016/s0301-679x(02)00216-5

    Article  CAS  Google Scholar 

  17. Casiraghi, C., Ferrari, A.C., Ohr, R., Flewitt, A.J., Chu, D.P., Robertson, J.: Dynamic roughening of tetrahedral amorphous carbon. Phys. Rev. Lett. 91(22), 226104 (2003)

    Article  CAS  Google Scholar 

  18. Casiraghi, C., Robertson, J., Ferrari, A.C.: Diamond-like carbon for data and beer storage. Mater. Today 10(1–2), 44–53 (2007)

    Article  CAS  Google Scholar 

  19. Bhushan, B.: Chemical, mechanical and tribological characterization of ultra-thin and hard amorphous carbon coatings as thin as 3.5 nm: recent developments. Diam. Relat. Mater. 8(11), 1985–2015 (1999). doi:10.1016/s0925-9635(99)00158-2

    Article  CAS  Google Scholar 

  20. Li, D.J., Guruz, M.U., Bhatia, C.S., Chung, Y.-W.: Ultrathin CNx overcoats for 1 Tb/in2 hard disk drive systems. Appl. Phys. Lett. 81(6), 1113–1115 (2002). doi:10.1063/1.1498866

    Article  CAS  Google Scholar 

  21. Shum, P.W., Zhou, Z.F., Li, K.Y.: Tribological performance of amorphous carbon films prepared on steel substrates with carbon implantation pre-treatment. Wear 256(3–4), 362–373 (2004). doi:10.1016/s0043-1648(03)00441-1

    Article  CAS  Google Scholar 

  22. Tong, H.H., Monteiro, O.R., Brown, I.G.: Effects of carbon ion pre-implantation on the mechanical properties of ta-C coatings on Ti-6Al-4V. Surf. Coat. Technol. 136(1–3), 211–216 (2001). doi:10.1016/s0257-8972(00)01058-6

    Article  CAS  Google Scholar 

  23. Park, C.K., Chang, S.M., Uhm, H.S., Seo, S.H., Park, J.S.: XPS and XRR studies on microstructures and interfaces of DLC films deposited by FCVA method. Thin Solid Films 420–421, 235–240 (2002). doi:10.1016/s0040-6090(02)00750-2

    Article  Google Scholar 

  24. Meyerson, B.S., Joshi, R.V., Rosenberg, R., Patel, V.V.: Silicon/carbon protection of metallic magnetic structures. US Patent 4647494

  25. Komvopoulos, K., Zhang, H., Bhatia, C.S.: Systems and methods for surface modification by filtered cathodic vacuum arc. US Patent aplication 20100190036

  26. Han, H., Ryan, F., McClure, M.: Ultra-thin tetrahedral amorphous carbon film as slider overcoat for high areal density magnetic recording. Surf. Coat. Technol. 120–121, 579–584 (1999). doi:10.1016/s0257-8972(99)00448-x

    Article  Google Scholar 

  27. Rismani, E., Sinha, S.K., Tripathy, S., Yang, H., Bhatia, C.S.: Effect of pre-treatment of the substrate surface by energetic C+ ion bombardment on structure and nano-tribological characteristics of ultra-thin tetrahedral amorphous carbon (ta-C) protective coatings. J. Phys. D Appl. Phys. 44(11), 115502 (2011). doi:10.1088/0022-3727/44/11/115502

    Article  Google Scholar 

  28. Rismani, E., Sinha, S. K., Yang, H., and Bhatia, C. S.: Effect of pre-treatment of Si interlayer by energetic C+ ions on the improved tribo-mechanical properties of magnetic head overcoat. J. Appl. Phys. (2012). doi:10.1063/1.3699058

  29. Anders, A.: Cathodic arcs: from fractal spots to energetic condensation. Springer Science, New York (2008)

    Google Scholar 

  30. Carlson, T.A.: Photoelectron and Auger Spectroscopy. Plenum Press, New York (1975)

    Google Scholar 

  31. Hedberg, C.L.: Handbook of auger electron spectroscopy. Physical Electronics, Inc

  32. Robertson, J.: Deposition mechanisms for promoting sp3 bonding in diamond-like carbon. Diam. Relat. Mater. 2(5–7), 984–989 (1993). doi:10.1016/0925-9635(93)90262-z

    Article  CAS  Google Scholar 

  33. Catledge, S., Vaid, R., Diggins, P., Weimer, J., Koopman, M., Vohra, Y.: Improved adhesion of ultra-hard carbon films on cobalt–chromium orthopaedic implant alloy. J. Mater. Sci. Mater. Med. 22(2), 307–316 (2011). doi:10.1007/s10856-010-4207-1

    Article  CAS  Google Scholar 

  34. Tang, Y., Li, Y.S., Zhang, C.Z., Wang, J., Yang, Q., Hirose, A.: Synthesis of cobalt/diamond-like carbon thin films by biased target ion beam deposition. Diam. Relat. Mater. 20(4), 538–541 (2011). doi:10.1016/j.diamond.2011.02.014

    Article  CAS  Google Scholar 

  35. Correa, S.A., Marmitt, G.G., Bom, N.M., da Rosa, A.T., Stedile, F.C., Radtke, C., Soares, G.V., Baumvol, I.J.R., Krug, C., Gobbi, A.L.: Enhancement in interface robustness regarding thermal oxidation in nanostructured Al2O3 deposited on 4H–SiC. Appl. Phys. Lett. 95(5), 051913–051916 (2009). doi:10.1063/1.3195702

    Article  Google Scholar 

  36. Klein, T.M., Niu, D., Epling, W.S., Li, W., Maher, D.M., Hobbs, C.C., Hegde, R.I., Baumvol, I.J.R., Parsons, G.N.: Evidence of aluminum silicate formation during chemical vapor deposition of amorphous Al2O3 thin films on Si(100). Appl. Phys. Lett. 75(25), 4001–4003 (1999). doi:10.1063/1.125519

    Article  CAS  Google Scholar 

  37. Prabhakaran, V., Talke, F.E.: Wear and hardness of carbon overcoats on magnetic recording sliders. Wear 243(1–2), 18–24 (2000). doi:10.1016/s0043-1648(00)00392-6

    Article  CAS  Google Scholar 

Download references

Acknowledgments

This research was partly funded by the Information Storage Industry Consortium (INSIC) TAPE Program and the Singapore NRF under CRP Award No. NRF-CRP 4-2008-6. The authors thank Dr. Robert Raymond of Oracle America Inc. for providing the heads and Mr. Douglas Johnson from Imation Corp. for providing the SDS tape transport system.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, Block EA, #07-08, Singapore, 117576, Singapore

    Ehsan Rismani & S. K. Sinha

  2. Department of Electrical and Computer Engineering, National University of Singapore, 4 Engineering Drive 3, Block E4, #05-45, Singapore, 117576, Singapore

    H. Yang & C. S. Bhatia

  3. Institute of Material Research and Engineering (IMRE), A*STAR (Agency for Science, Technology, and Research), 3 Research Link, Singapore, 117602, Singapore

    S. Tripathy

Authors
  1. Ehsan Rismani
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. K. Sinha
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. H. Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. Tripathy
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. C. S. Bhatia
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to C. S. Bhatia.

Rights and permissions

Reprints and Permissions

About this article

Cite this article

Rismani, E., Sinha, S.K., Yang, H. et al. Development of a ta-C Wear Resistant Coating with Composite Interlayer for Recording Heads of Magnetic Tape Drives. Tribol Lett 46, 221–232 (2012). https://doi.org/10.1007/s11249-012-9941-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11249-012-9941-8

Keywords

  • Magnetic data recording heads
  • Carbon
  • Ceramic
  • Coatings
  • Wear-resistant
  • Surface modification
  • Delamination wear
  • AES (Auger)