Skip to main content
SpringerLink
Log in

Tribometer Investigation of the Frictional Response of Piston Rings when Lubricated with the Separated Phases of Lubricant Contaminated with the Gasoline Engine Biofuel Ethanol and Water

  • Original Paper
  • Published:
Tribology Letters Aims and scope Submit manuscript

Abstract

The biofuel ethanol, a viable and cost-effective gasoline substitute, is being blended at increasingly higher concentrations in gasoline, heightening the need to investigate its effects on current automotive engine lubricants in terms of fuel economy and engine durability. The friction at the piston ring/cylinder wall interface with a fully formulated gasoline engine lubricant contaminated with ethanol and water was investigated using a Plint TE77 reciprocating tribometer and reported in a previous paper by the authors. This research takes this one stage further by studying the friction in the same tribometer configuration when lubricated with the separated phases the same contaminated lubricant forms when left undisturbed, as would happen when a vehicle is parked or garaged. The lubricant mixture separated into two distinct phases, an oil phase and a water and ethanol based ‘white sludge’ phase, both phases characterised by FTIR spectroscopy and viscosity. Significant reductions in friction were obtained when the piston ring-cylinder wall interface was lubricated with the separated phases compared to the formulated reference lubricant. When lubricated with the separated oil phase, temperature was shown to be the dominant contributor to the frictional response. When lubricated with the separated sludge phase, ethanol independently contributed to the frictional response whilst the interactions between ethanol and temperature, water and temperature and water and speed were also important.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14

Similar content being viewed by others

Abbreviations

CO2 :

Carbon dioxide

OEM:

Original equipment manufacturer

XHVI™:

Extra high viscosity index

ANOVA:

Analysis of variance

S/NHB :

Signal-to-noiseHigher-the-Better

SNR:

Signal-to-noise ratio

FTIR:

Fourier transform infrared

OH:

Hydroxyl

ZDDP:

Zinc dialkyl dithiophosphate

References

  1. Balat, M., Balat, H.: Recent trends in global production and utilization of bio-ethanol fuel. Appl. Energy 86(11), 2273–2282 (2009)

    Article  CAS  Google Scholar 

  2. Chui, G.K., Millard, D.H.T.: Development and Testing of Crankcase Lubricants for Alcohol Fueled Engines. SAE 811203 (1981)

  3. Chui, G.K., King, E.T., Groff, W.P.: Modified Sequence V-D Test with Two Engines Using Alcohol Fuels. SAE 830239 (1983)

  4. Ernst, R.J., Pefley, R.K., Wiens, F.J. Methanol Engine Durability. SAE 831704 (1983)

  5. Marbach, H.W., Frame, E.A., Owens, E.C., Naegeli, D.W.: The Effects of Lubricant Composition on S.I. Engine Wear with Alcohol Fuels. SAE 831702 (1983)

  6. Chaibongsai, S., Howlett, B.J., Millard, D.H.T.: Development of an Engine Screening Test to Study the Effect of Methanol Fuel on Crankcase Oils. SAE 830240 (1983)

  7. Hansen, A.C., Zhang, Q., Lyne, P.W.L.: Ethanol-diesel fuel blends—a review. Bioresour. Technol. 96(3), 277–285 (2005)

    Article  CAS  Google Scholar 

  8. Wallner, T., Miers, S.A.: Combustion Behaviour of Gasoline and Gasoline/Ethanol Blends in a Modern Direct-Injection 4-Cylinder Engine. SAE 2008-01-0077 (2008)

  9. Chui, G.K., Baker, R.E., Pinto, F.B.P.: Lubrication behaviour in ethanol-fuelled engines. In: 4th Symposium on Alcohol Fuels, Guaruja, Brazil (1980)

  10. Tsunooka, T., Hosokawa, Y., Utsumi, S., Kawai, T., Sonoda, Y.: High Concentration Ethanol Effect on SI Engine Cold Startability. SAE 2007-01-2036 (2007)

  11. Schwartz, S.E., Smolenski, D.J., Clark, S.L.: Entry and Retention of Methanol Fuel in Engine Oil. SAE 880040 (1988)

  12. Boons, M., Bulk, R.V.D., King, T.: The Impact of E85 Use on Lubricant Performance. SAE 2008-01-1763 (2008)

  13. Canter, N.: Proper Additive Balance Needed to Meet GF-5, vol. 66. Tribology and Lubrication Technology (TLT), Society of Tribologists and Lubrication Engineers (2010)

  14. Al-Hasan, M.: Effect of ethanol-unleaded gasoline blends on engine performance and exhaust emission. Energy Convers. Manag. 44(9), 1547–1561 (2003)

    Article  CAS  Google Scholar 

  15. Ferrarese, A., Marques, G., Tomanik, E., Bruno, R., Vatavuk, J.: Piston Ring Tribological Challenges on the Next Generation of Flex-Fuel Engines. SAE 2010-01-1529 (2010)

  16. Tung, S.C., McMillan, M.L.: Automotive tribology overview of current advances and challenges for the future. Tribol. Int. 37, 517–536 (2004)

    Article  CAS  Google Scholar 

  17. Mufti, R.A., Priest, M.: Effect of engine operating conditions and lubricant rheology on the distribution of losses in an internal combustion engine. J. Tribol. 131(4), 041101–041109 (2009)

    Article  Google Scholar 

  18. De Silva, P.R., Priest, M., Lee, P.M., Coy, R.C., Taylor, R.I.: Tribometer investigation of the frictional response of piston rings with lubricant contaminated with the gasoline engine biofuel ethanol and water. Proc. Inst. Mech. Eng. Part J: J. Eng. Tribol. (2011). doi:10.1177/2041305X10394758

  19. Furey, M.J.: Metallic contact and friction between sliding surfaces. Am. Soc. Lubr. Eng. Trans. 4(1), 1–11 (1961)

    Google Scholar 

  20. Smith, O.M., Priest, M., Taylor, R.I., Price, R., Cantlay, A., Coy, R.C.: Simulated fuel dilution and friction-modifier effects on piston ring friction. Proc. IMechE, Part J: J. Eng. Tribol. 220(3), 181–189 (2006). doi:10.1243/13506501JET162

    Article  CAS  Google Scholar 

  21. Coates, J.P., Setti, L.C.: Infrared spectroscopy as a tool for monitoring oil degradation. In: Stadtmiller, W.H., Smith, A.N. (eds.) Aspects of Lubrication Oxidation, ASTM STP 916, pp. 57–78. American Society for Testing and Materials, Philadelphia (1986)

  22. Van de Voort, Sedman, F.R.J., Cocciardi, R.A., Pinchuk, D.: FTIR condition monitoring of in-service lubricants: ongoing developments and future perspectives. Tribol. Trans. 49, 410–418 (2006)

    Article  CAS  Google Scholar 

  23. Coates, J.P., Setti, L.C.: Condition Monitoring of Crankcase Oils Using Computer Aided Infrared Spectroscopy. SAE 831681 (1983)

  24. Powell, J.R., Compton, A.C.: Automated FTIR spectrometry for monitoring hydrocarbon-based engine oils. J. Soc. Tribol. Lubr. Eng. 49(3), 233–239 (1992)

    Google Scholar 

  25. Griffiths, P.R., de Haseth, J.A. (eds.): Fourier Transform Infrared Spectrometry. Wiley, New York (2007)

    Google Scholar 

  26. Ross, P.J.: Taguchi Techniques for Quality Engineering. McGraw-Hill Book Company, New York (1988)

    Google Scholar 

  27. Win, Z., Gakkhar, R.P., Jain, S.C., Bhattacharya, M.: Investigation of diesel engine operating and injection system parameters for low noise, emissions, and fuel consumption using Taguchi methods. Proc. Inst. Mech. Eng. D 219, 1237–1251 (2005)

    Article  Google Scholar 

  28. Mang, T., Dresel, W.: Lubricants and Lubrication. Wiley-VCH, New York (2001)

    Google Scholar 

  29. Arai, K., Yamada, M., Asano, S., Yoshizawa, S., Ohira, H., Hoshino, K., Ueda, F., Akiyama, K.: Lubricant Technology to Enhance the Durability of Low Friction Performance of Gasoline Engine Oils. SAE 952533 (1995)

  30. Yaguchi, A., Inoue, K.: Development and Field Test Performance of Fuel Efficient SAE 5W-20 Oils. SAE 952341 (1995)

Download references

Acknowledgments

The authors would like to sincerely thank Shell Global Solutions (UK) for funding this research, Rob Wetton of Shell Global Solutions (UK) for conducting FTIR analysis on the oil and sludge phases and the technical staff at the University of Leeds for their help and support. The authors would like to especially thank Mr. Paul Banks of the University of Leeds for his dedicated help throughout.

Author information

Authors and Affiliations

  1. iETSI, School of Mechanical Engineering, University of Leeds, Leeds, LS2 9JT, UK

    P. R. De Silva, M. Priest, P. M. Lee & R. C. Coy

  2. Shell Global Solutions (UK), Chester, CH1 3SH, UK

    R. I. Taylor

Authors
  1. P. R. De Silva
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. Priest
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. P. M. Lee
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. R. C. Coy
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. R. I. Taylor
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to P. R. De Silva.

Rights and permissions

Reprints and permissions

About this article

Cite this article

De Silva, P.R., Priest, M., Lee, P.M. et al. Tribometer Investigation of the Frictional Response of Piston Rings when Lubricated with the Separated Phases of Lubricant Contaminated with the Gasoline Engine Biofuel Ethanol and Water. Tribol Lett 43, 107–120 (2011). https://doi.org/10.1007/s11249-011-9809-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11249-011-9809-3

Keywords

Search

Navigation