Skip to main content
SpringerLink
Log in

Effect of Shock and Vibration Preloading on the Deformation and Fracture Behavior of 17G1S-U Steel

  • Published:
Strength of Materials Aims and scope

The procedure of evaluating the crack resistance of 17G1S-U sheet steel after shock and vibration loading was advanced and experimentally tested using the method of complete deformation diagrams. The technical potential was employed to provide the growth of a mixed mode (I+III) macrocrack on the specimens with an identical central circular opening, which guaranteed the self-similar macrocrack propagation. The complete deformation diagrams displayed initial almost straight descending portion. In real constructions of gas mains, rather long macrocracks can arise after this fracture mode. The advanced procedure permits of reliable assessment of energy variations spent for a (I+III) mode crack propagation under any complex combined loading. The straight descending branch slope of the deformation diagram is established to be used for evaluating crack resistance variations of pipe steel subject to thermomechanical loading. Shock and vibration loading of a high frequency (1–2 kHz) is shown to essentially influence the crack resistance of pipe steel and plastic strain in the vicinity of a stress raiser. The impact of a power pulse on the material is dependent on its prestrain level through static tension and damage of its initial structure correspondingly. The controlling factor influencing the change in mechanical properties is the intensity of the power pulse. Basic fracture mechanisms of steel were established on the basis of examination of specimen fractures with scanning electron microscopy. The shock and vibration loading is evidently accompanied by energy contribution not only to the existing damages of the material but also to the initiating ones, which causes the localization of deformation and growth of pores in their vicinity. Since the energy accumulation can contribute to the modification of the material in the vicinity of those damages, the shape and sizes of ductile tear dimples are the informative parameters for evaluating the strength and plasticity of examined steel.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.
Fig. 7.

Similar content being viewed by others

References

  1. V. F. Pichugin (Ed.), P. O. Marushchak, S. V. Panin, et al., Large-Scale Strain and Fracture Levels for Heat-Resistant Steels [in Russian], TPU, Tomsk (2013).

  2. S. V. Panin, P. O. Maruschak, I. V. Vlasov, et al., “Impact toughness of 12Cr1MoV steel. Part 2 – Influence of high intensity ion beam irradiation on energy and deformation parameters and mechanisms of fracture,” Theor. Appl. Fract. Mech., 83, 82–92 (2016).

    Article  Google Scholar 

  3. M. G. Chausov, P. O. Marushchak, A. P. Pylypenko, and V. V. Berezin, Deformation and Fracture Behavior of Plastic Materials under Shock and Vibration Loading [in Ukrainian], Terno-graf, Ternopil (2018).

    Google Scholar 

  4. M. G. Chausov, A. P. Pylypenko, and P. O. Marushchak, Procedure of Improving the Plastic Properties of Sheet Two-Phase High-Strength Titanium Alloys by Shock and Vibration Loading: Scientific-Methodical Recommendations for Plants of Ukraine as Regards Designing of Agricultural Equipment Manufacture [in Ukrainian], FOP V. A. Palyanytsya, Ternopil (2017).

  5. N. G. Chausov and A. P. Pilipenko, “Influence of dynamic overloading on fracture kinetics of metals at the final stages of deformation,” Mechanika, 48, 13–18 (2004).

    Google Scholar 

  6. M. G. Chausov, V. B. Berezin, A. P. Pylypenko, and V. B. Hutsaylyuk, “Strain field evolution on the surface of aluminum sheet alloys exposed to specific impact with oscillation loading,” J. Strain Anal. Eng., 50, No. 1, 61–72 (2015).

    Article  Google Scholar 

  7. M. Chausov, V. Hutsaylyuk, L. Sniezek, et al., “Strain field evolution on the surface of stainless sheet steel 12Cr17 exposed to a specific impact with oscillation loading,” in: Proc. of the 11th Int. Conf. on Intelligent Technologies in Logistics and Mechatronics Systems (ITELMS’2016, April 28–29, 2016, Panevéþys, Lithuania), Medimond, Bologna, Italy (2016), pp. 47–52.

  8. M. G. Chausov, O. E. Zasymchuk, and K. M. Volyans’ka, “Studies on the display process of yield plateaus under pulse load adjustment of aluminum alloys,” Visn. NTUU “KPI”, Ser. Mashynobuduvannya, No. 63, 244–248 (2011).

  9. M. G. Chausov, A. P. Pylypenko, V. B. Berezin, et al., “Influence of impact-oscillatory loading upon the mechanical properties of the VT-22 titanium alloy sheet,” J. Mater. Eng. Perfom., 25, No. 8, 3482–3492 (2016).

    Article  Google Scholar 

  10. S. V. Panin, P. O. Maruschak, I. V. Vlasov, and O. Prentkovskis, “Effect of stress concentrator shape on impact fracture mechanisms of 17Mn1Si steel,” Procedia Engineer., 165, 1925–1930 (2016).

    Article  Google Scholar 

  11. P. O. Maruschak, S. V. Panin, M. G. Chausov, et al., “Effect of long-term operation on steels of main gas pipeline. Reduction of static fracture toughness,” J. Nat. Gas Sci. Eng., 38, 182–186 (2017).

    Article  Google Scholar 

  12. V. Hutsaylyuk, M. Chausov, V. Berezin, et al., “Influence of dissipative structures formed by impulse loads on the processes of deformation and fracture,” Key Eng. Mater., 577–578, 273–276 (2014).

    Google Scholar 

  13. M. Chausov, P. Maruschak, A. Pylypenko, and L. Markashova, “Enhancing plasticity of high-strength titanium alloys VT22 under impact-oscillatory loading,” Philos. Mag., 97, No. 6, 389–399 (2017).

    Article  Google Scholar 

  14. A. A. Lebedev and N. G. Chausov, New Methods of Evaluating In-Service Degradation of Mechanical Properties of the Structure Metal [in Russian], Pisarenko Institute of Problems of Strength, National Academy of Sciences of Ukraine, Kiev (2004).

    Google Scholar 

  15. N. G. Chausov, “Complete deformation diagram as the source of information on the kinetics of damage accumulation and crack resistance of materials,” Zavod. Lab. Diagnost. Mater., 70, No. 7, 42–49 (2004).

    Google Scholar 

  16. M. G. Chausov, A. P. Pylypenko, P. O. Marushchak, and V. A. Dovganyuk, Method of Assessment of the Pulse Energy Input to the Plastic Material [in Ukrainian], Patent of Ukraine No. 113940, Valid since March 27, 2017, Bull. No. 6.

  17. M. A. Smirnov, I. Yu. Pyshmintsev, A. N. Maltseva, and O. V. Mushina, “Effect of ferrite-bainite structure on the properties of high-strength pipe steel,” Metallurgist, 56, Nos. 1–2, 43–51 (2012).

    Article  Google Scholar 

  18. V. M. Farber, I. Yu. Pyshmintsev, A. B. Arabei, et al., “Contributions of structural factors to the strength of K65 steels,” Steel Transl., 42, No. 9, 687–690 (2012).

    Article  Google Scholar 

  19. I. N. Veselov, I. Yu. Pyshmintsev, K. A. Laev, and S. Yu. Zhukova, “Structure and mechanical properties of low-carbon steel for oil and gas pipelines,” Steel Transl., 41, No. 2, 165–170 (2011).

    Article  Google Scholar 

  20. P. O. Marushchak, R. T. Bishchak, and I. M. Danylyuk, Crack Resistance of Materials and Structures: Long-Term Operated Gas Mains [in Ukrainian], Zazaprint, Ternopil (2016).

  21. S. V. Panin, D. D. Moiseenko, P. V. Maksimov, et al., “Influence of energy dissipation at the interphase boundaries on impact fracture behaviour of a plain carbon steel,” Theor. Appl. Fract. Mech., 97, 478–499 (2018).

    Article  Google Scholar 

  22. I. Sevostianov and M. Kachanov, “Is the concept of “average shape” for a mixture of inclusions of diverse shapes legitimate?” Int. J. Solids Struct., 49, 3242–3254 (2012).

    Article  Google Scholar 

  23. I. Sevostianov and M. Kachanov, “Normal and tangential compliances of interface of rough surfaces with contacts of elliptic shape,” Int. J. Solids Struct., 45, 2723–2732 (2008).

    Article  Google Scholar 

  24. Y. Sun, X. Li, X. Yu, et al., “Fracture morphologies of advanced high strength steel during deformation,” Acta Metall. Sin. (Engl. Lett.), 27, No. 1, 101–106 (2014).

    Article  Google Scholar 

  25. S. Osovski, D. Rittel, J. A. Rodriguez-Martinez, and R. Zaera, “Dynamic tensile necking: Influence of specimen geometry and boundary conditions,” Mech. Mater., 62, 1–13 (2013).

    Article  Google Scholar 

  26. A. Dorogoy, D. Rittel, and A. Godinger, “A shear-tension specimen for large strain testing,” Exp. Mech., 56, No. 3, 437–449 (2015).

    Article  Google Scholar 

  27. M. Chausov, A. Pylypenko, V. Berezin, et al., “Influence of dynamic non-equilibrium processes on strength and plasticity of materials of transportation systems,” Transport, 33, No. 1, 231–241 (2018).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine

    P. O. Marushchak & A. P. Sorochak

  2. National University of Life and Environmental Sciences, Kyiv, Ukraine

    M. G. Chausov & A. P. Pylypenko

Authors
  1. P. O. Marushchak
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. G. Chausov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. P. Pylypenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. P. Sorochak
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to P. O. Marushchak.

Additional information

Translated from Problemy Prochnosti, No. 3, pp. 114 – 125, May – June, 2019.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Marushchak, P.O., Chausov, M.G., Pylypenko, A.P. et al. Effect of Shock and Vibration Preloading on the Deformation and Fracture Behavior of 17G1S-U Steel. Strength Mater 51, 418–426 (2019). https://doi.org/10.1007/s11223-019-00088-3

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11223-019-00088-3

Keywords

Search

Navigation