The paper focuses on upset forging of the sintered Al–7Fe–38Sn alloy in a closed mold and the process temperature, both affecting its structure and tribological properties. The Al–7Fe–38Sn composite consists of the hard (Al3Fe) and soft (Sn) phases in 17 and 20 volume fractions, respectively. It is found that ≤250°C forging has a negative effect on the composite plasticity, whereas at 300°C, the plasticity restores and even grows after multiple compression. Tensile strength of the composite remains stable and is ~130 MPa. It is found that Al3Fe phase particles intensively dissolve during heating up to the forging temperature in the presence of liquid tin.
Similar content being viewed by others
References
N. A. Bushe, A. S. Gulyaev, V. A. Dvoskina, and K. M. Rakov, Bearings Made of Aluminum Alloys, Transport, Moscow (1974).
E. Huttunen-Saarivirta, L. Kilpi, T. J. Hakala, et al., Tribol. Int., 119, 567–584 (2018); https://doi.org/10.1016/j.triboint.2017.11.041.
A. E. Mironov, I. S. Gershman, and E. I. Gershman, J. Frict. Wear, 39, 394–399 (2018); https://doi.org/10.3103/S1068366618050100.
A. E. Mironov, I. S. Gershman, E. G. Kotova, et al., Russ. Engin. Res., 37, 37–39 (2017); https://doi.org/10.3103/S1068798X17010154.
C. Zhang, L. Li, Q. Jiang, et al., J. Alloy. Compd., 861, 157980 (2021);://doi.org/https://doi.org/10.1016/j.jallcom.2020.157980.
P. Podrabinnik, I. Gershman, A. Mironov, et al., Lubricants, 6, 104 (2018); https://doi.org/10.3390/lubricants6040104.
D. Wang, X. Wu, K. Gao, et al., J. Mater. Res. Technol., 18, 338–351 (2022); https://doi.org/10.1016/j.jmrt.2022.02.087.
M. Q. Zeng, R. Z. Hu, K. Q. Song, et al., Tribol. Lett., 67, 84 (2019); https://doi.org/10.1007/s11249-019-1195-2.
V. Shyrokov and O. Khlopyk, Mater. Sci., 46, 371–375 (2010); https://doi.org/10.1007/s11003-010-9299-8.
D. M. Goudar, V. C. Srivastava, G. B. Rudrakshi, et al., Trans. Indian Inst. Met., 68, 3–7 (2015); https://doi.org/10.1007/s12666-015-0573-1.
E. J. Abed, Asian Trans. Eng., 2, 89–98 (2012).
M. R. Tripathy, B. V. Manoj Kumar, B. Basu, et al., Mater. Sci. Technol., 23, No. 1, 15–22 (2007); https://doi.org/10.1179/174328407X154392.
N. M. Rusin, A. L. Skorentsev, and E. A. Kolubaev, J. Mater. Eng. Perf., 29, 1955–1963 (2020); https://doi.org/10.1007/s11665-020-04704-1.
N. M. Rusin, A. L. Skorentsev, and J. Frict. Wear, 43, 153–159 (2022); https://doi.org/10.3103/S1068366622030126.
A. P. Savitskii, Liquid Phase Sintering of the Systems with Interacting Components. Kluwer Academic Plenum Publishers, New York (1999).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Rusin, N.M., Skorentsev, A.L. & Likharev, V.E. Upset Forging Temperature Effect on Structure and Tribological Properties of Sintered Al–7Fe–38Sn Alloy. Russ Phys J 67, 9–16 (2024). https://doi.org/10.1007/s11182-024-03082-8
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11182-024-03082-8