The paper focuses on the thermal treatment effect on structural properties and heat capacity of the extruded Mg–2.9Y–1.3Nd alloy. It is shown that the bimodal temperature dependence of the heat capacity for the extruded Mg–2.9Y–1.3Nd alloy is determined by the structural and phase transformation during annealing process in the temperature range of 300 to 450°C according to β′→ β1→ β, β′→ β, or β1→β cascade reactions. This dependence is associated with the complex structure, i.e., base α-phase dispersion-hardened with Mg24Y5 nanoparticles, metastable β′- and β1-phases, and equilibrium β-phase.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
F. Witte, N. Hort, C. Vogt, et al., Curr. Opin. Solid State Mater. Sci., 12, 63 (2008); https://doi.org/10.1016/j.cossms.2009.04.001.
X. Lin, L. Tan, Q. Zhang, et al., Acta Biomater., 9, 8631 (2013); https://doi.org/10.1016/j.actbio.2012.12.016.
Y. Zheng, X. Gu, and F. Witte, Mater. Sci. Eng. R Rep., 77, 1 (2014); https://doi.org/10.1016/j.mser.2014.01.001.
J. Bohlen, S. Yi, D. Letzig, et al., Mater. Sci. Eng. A, 527, 7092 (2010); https://doi.org/10.1016/j.msea.2010.07.081.
L. Atwell and R. Barnett, Metall. Mater. Trans. A, 38, 3032 (2007); https://doi.org/10.1007/s11661-007-9323-2.
Z. Zeng, J.Nie, and S. Xu, Nat. Commun., 8, 972 (2017); https://doi.org/10.1038/s41467-017-01330-9.
J. Walker, S. Shadanbaz, and T. Woodfield, Mater. Res. B Appl. Biomater., 102, 1316 (2014); https://doi.org/10.1002/jbm.b.33113.
Yu. P. Sharkeev, V. P. Vavilov, V. A. Skrypnyak, et al., Mater. Sci. Eng. A, 784, 139203 (2020); https://doi.org/10.1016/j.msea.2020.139203.
E. V. Legostaeva, Yu. P. Sharkeev, O. A. Belyavskaya, et al., Russ. Phys. J., 63, No. 11, 1867 (2021); 1110.1007/s11182-021-02270-0.
E. V. Legostaeva, M. A. Khimich, Y. P. Sharkeev, et al., Russ. Phys. J., 64, 1676 (2022); https://doi.org/10.1007/s11182-022-02506-7.
V. I. Gorbatov, V. F. Polev, V. P. Pilugin, et al., High Temp., 51, No. 4, 482 (2013); https://doi.org/10.1134/S0018151X1602005X.
A. L. Smirnov, S. G. Talutz, D. Ivliev, et al., High Temp., 55, No. 3, 380 (2017); https://doi.org/10.1134/S0018151X17020183.
F. R. Elsayed, N. Hort, M. A. Salgado-Ordoric, et al., Mater. Sci. Forum, 690, 65 (2011); https://doi.org/10.4028/www.scientific.net/MSF.690.65.
ASTM E1382-97 – Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis (2016).
M. Ladd and R. Palmer, in: Analysis by X-rays and Neutrons, Springer, New York (2013).
ASTM E1269 – Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry (2011).
J. F. Nie, Metall. Mater. Trans. A, 43, 3891 (2012); https://doi.org/10.1007/s11661-012-1217-2.
J. Nie and B. Muddle, Acta Mater., 48, 1691 (2000); https://doi.org/10.1016/S1359-6454(00)00013-6.
P. Mengucci, G. Barucca, G. Riontino, et al., Mater. Sci. Eng. A, 47, 37 (2008); https://doi.org/10.1016/j.msea.2007.06.016.
Y. Kang, Z. Huang, S. Wang, et al., J. Magnes. Alloy., 8, 103 (2020); https://doi.org/10.1016/j.jma.2019.11.012.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Legostaeva, E.V., Eroshenko, A.Y., Khimich, M.A. et al. Influence of Thermal Treatment of the Extruded Mg–2.9Y–1.3Nd Alloy on Its Structural Parameters and Heat Capacity. Russ Phys J 66, 1031–1038 (2023). https://doi.org/10.1007/s11182-023-03040-w
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11182-023-03040-w