Abstract
Results of studies on the influence of microstress on the parameters of electromagnetic-acoustic transduction (EMAT) in thermally treated and cold-worked steels are presented. It is shown that in thermally treated steels, except high-alloy corrosion-resistant austenite-martensite steel 1Kh15N5AM3Sh, the amplitude of the EMAT signal decreases linearly with an increase in the microstress. In this situation, the propagation velocity of normal elastic waves also decreases monotonously; this is also the case for 1Kh15N5AM3Sh steel. In pearlitic steel that is cold-worked by drawing, the dependences of the EMAT amplitude and the propagation velocity are linear only at the initial stage of deformation. After that, the parameters of the EMAT are affected most strongly by the phenomena that occur during the drawing: the turning of ferrite and carbide plates and the decrease in the dispersion angle of the axial crystallographic structure.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
N.P. Aleshin V.E. Belyi A.Kh. Vopilkin (1989) Metody akusticheskogo kontrolya metallov Mashinostroenie Moscow
Bobrenko, V.M. and Averbukh, I.I., Investigation of Stresses with the Use Of Electromagnetic Acoustic-Emission Transducers, Defectoskopiya, 1971, no. 3, pp. 132–134.
M.N. Mikheev E.S. Gorkunov (1993) Magnitnye metody strukturnogo analiza i nerazrushayushchego kontrolya Nauka Moscow
Yu.A. Geller (1968) Instrumental’nye stali Metallurgiya Moscow
Lysak, L.I., Analysis of Second-Kind Stresses in the α-Phase in Quenched and Tempered Steels, Izv. Akad. Nauk SSSR, Ser.: Fiz., 1956, no. 6, pp. 624–630.
Voznesenskaya, N.M., Izotov, V.I., Ul’yanova, N.V., Popova, L.S., and Potak, Ya.S., Structure and Properties of High-Strength Stainless Steel 1Kh15N4AM3, Metalloved. Term. Obrab. Met., 1978, no. 1, pp. 32–35.
V.N. Gridnev V.G. Gavrilyuk Yu.Ya. Meshkov (1974) Prochnost’ i plastichnost’ kholodnodeformirovannoi stali Naukova Dumka Kiev
S.V. Vonsovskii Ya.S. Shur (1948) Ferromagnetizm OGIZ Moscow
M.V. Belous V.T. Cherepin (1962) ArticleTitleChanges in the Carbide Phase in Steel under the Influence of Cold Plastic Deformation Fiz. Met. Metalloved. 14 IssueID1 48–54
Grachev, S.V., Gorkunov, E.S., Smirnov, S.V., Mikhailov, S.B., Somova, V.M., Rakovskaya, A.U., and Soloshenko, A.N., The Influence of Large Drawing Deformations on the Physical and Mechanical Properties of Patented Wire, Trudy XXXV seminara “Aktual’nye problemy prochnosti” (Proc. of XXXV Seminar on Current Problems of Strength), Pskov, 1999, pp. 403–408.
G.V. Samsonov (Eds) (1976) Svoistva elementov. Spravochnik, Chast’ 1: Fizichesie svoistva Metallurgiya Moscow
V.S. Postnikov (1969) Vnutrennee trenie v metallakh Metallurgiya Moscow
Shakshin, N.I., and Deordiev, G.I., Method of Tuning-out the Influence of Damping Factors in Resonance Electromagnetic-Acoustic Inspection, Defectoskopiya, 1986, no. 12, pp. 11–20.
V.A. Komarov (1986) Kvazistatsionarnoe elektromagnitno-akusticheskoe preobrazovanie v metallak UNTs AN SSSR Sverdlovsk
Author information
Authors and Affiliations
Additional information
Translated from Defektoskopiya, Vol. 40, No. 7, 2004, pp. 26–33.
Original Russian Text Copyright © 2004 by Gorkunov, Zadvorkin, Solomein.
Rights and permissions
About this article
Cite this article
Gorkunov, E.S., Zadvorkin, S.M. & Solomein, M.N. Utilization of electromagnetic acoustic conversion to estimate microstress in steels. Russ J Nondestruct Test 40, 449–454 (2004). https://doi.org/10.1007/s11181-005-0068-y
Received:
Issue Date:
DOI: https://doi.org/10.1007/s11181-005-0068-y