Refractories and Industrial Ceramics

, Volume 58, Issue 3, pp 338–342 | Cite as

Stressed State of Boundary Between TiC/TiN-Coating Layers Applied to Nitride Ceramic Under Action of a Force Load

Article
  • 18 Downloads

The main stressed state features are established at a boundary between layers of a two-layer TiC/TiN coating applied to nitride ceramic under action of concentrated and distributed forces. The effect of ceramic basic structural element on stresses formed in TiC/TiN-coating underlayers in contact under action of force loads is determined.

Keywords

nitride ceramic coating layer boundary stresses force load 

Notes

This work was conducted with support of the Russian Ministry of Science and Technology within the scope of fulfilling a state assignment (assignment 9.1372.2017/4.6)

References

  1. 1.
    S. N. Grigor’ev and M. A. Volosova, “Complex surface hardening of oxide-carbide ceramic cutting tools,” Russ. Eng. Res., 25(9), 7 – 12 (2005).Google Scholar
  2. 2.
    M. Volosova and S. Grigor’ev, “Cutting ceramic inserts: the influence of abrasive machining and surface coatings on the operational haracteristics,” Mech. Ind., 17(7), 705 (2016).CrossRefGoogle Scholar
  3. 3.
    V. V. Kuzin, “Effective use of high density ceramic for manufacture of cutting and working tools,” Refract. Indust. Ceram., 51(6), 421 – 426 (2010).CrossRefGoogle Scholar
  4. 4.
    V. P. Tabakov and A. A. Ermolaev, “Multi-layer coatings of the tools operating in continuous cutting conditions,” Russ. Eng. Res., 25(7), 61 – 65 (2005).Google Scholar
  5. 5.
    M. Sokovi’c, J. Miku∤a, L. A. Dobrza’nski, et al., “Cutting properties of the Al2O3 + SiC(w) based tool ceramic reinforced with the PVD and CVD wear resistant coatings,” J. Mater. Proc. Technol., 164/165, 924 – 929 (2005).CrossRefGoogle Scholar
  6. 6.
    Zh. Peng, H. Miao,W.Wang, et al., “Hard and wear-resistant titanium nitride films for ceramic cutting tools by pulsed high energy density plasma,” Surf. Coat. Technol., 6, 183 – 188 (2003.).CrossRefGoogle Scholar
  7. 7.
    V. V. Kuzin, “Development and study of cutting tools of nitride ceramic with a coating,” Traktor. Sel’sk. Masihniy, No. 9, 48 – 52 (2006).Google Scholar
  8. 8.
    M. Nakamichi, T. Takabatake, and H. Kawamura, “Material design of ceramic coating by plasma spray method,” Fusion Eng. Des., 41, 143 – 147 (1998).CrossRefGoogle Scholar
  9. 9.
    V. Kuzin and S. Grigoriev, “Tool life and wear mechanism of coated Si3N4 ceramic tools in turning grey cast iron,” Key Eng. Mater., 581, 14 – 17 (2014).CrossRefGoogle Scholar
  10. 10.
    V. P. Tabakov and A. V. Chikhranov, “Study of crack formation in wear-resistant coatings on a cutting tool,” Vestn. Tambov. Univ., Ser. Estest. Tekhn. Nauki, 18(402), 1916 – 1918 (2013).Google Scholar
  11. 11.
    M. A. Volosova, S. N. Grigor’ev, and V. V. Kuzin, “Effect of titanium nitride coatings on stress structural inhomogeneity in oxide-carbide ceramic. Part 2. Concentrated force action,” Refract. Indust. Ceram., 55(5), 487 – 491 (2.15).Google Scholar
  12. 12.
    M. A. Volosova, S. N. Grigor’ev, and V. V. Kuzin, “Effect of titanium nitride coating on stress structural inhomogeneity in oxide-carbide ceramic. Part 3. Action of distributed force load,” Refract. Indust. Ceram., 55(6), 565 – 569 (2015).CrossRefGoogle Scholar
  13. 13.
    M. A. Volosova, S. N. Grigor’ev, and V. V. Kuzin, “Effect of titanium nitride coating on stress structural inhomogeneity in oxide-carbide ceramic. Part 4. Action of heat flow,” Refract. Indust. Ceram., 56(1), 91 – 96 (2/15).Google Scholar
  14. 14.
    M. A. Volosova, S. N. Grigor’ev, and V. V. Kuzin, “Effect of titanium nitride coating on stress structural inhomogeneity in oxide-carbide ceramic. Part 5. A combined load operates,” Refract. Indust. Ceram., 56(2), 197 – 200 (2015).CrossRefGoogle Scholar
  15. 15.
    S. N. Grigor’ev, V. V. Kuzin, and M. A. Volosova, “Stress-strain state of a coated nitride ceramic tool,” Russ. Eng. Res., 32(7/8), 561 – 566 (2012).CrossRefGoogle Scholar
  16. 16.
    V. V. Kuzin, and M. A. Volosova, “main features of the effect of coating thickness on the stress-strained state of a ceramic surface layer,” Uproch. Tekhnol. Pokrytiya, No. 6, 12 – 17 (2015).Google Scholar
  17. 17.
    V. V. Kuzin, S. N. Grigor’ev, and M. A. Volosova, “Effect of a TiC coating on the stress-strain state of a plate of a high-density nitride ceramic under nonsteady thermoelastic conditions,” Refract. Indust. Ceram., 54(5), 376 – 380 (2014).CrossRefGoogle Scholar
  18. 18.
    V. V. Kuzin and M. Y. Fedorov, “The stressed state of the boundary between ceramic and a coating under the effect of power loads,” Refract. Indust. Ceram., 57(2), 192 – 198 (2016).CrossRefGoogle Scholar
  19. 19.
    V. V. Kuzin and M. Y. Fedorov, “Stressed state of a boundary between ceramic and coating under action of a combined load,” Refract. Indust. Ceram., 57(3), 308 – 312 (2016).CrossRefGoogle Scholar
  20. 20.
    V. V. Kuzin, “Microstructural model of ceramic cutting plate,” Russ. Eng. Res., 31(5), 479 – 483 (2011).CrossRefGoogle Scholar
  21. 21.
    S. N. Grigor’ev, V. I. Myachenkov, and V. V. Kuzin, “ Automated thermal-strength calculations of ceramic cutting plates,” Russ. Eng. Res., 31(11), 1060 – 1066 (2011).Google Scholar
  22. 22.
    V. Kuzin and S. Grigor’ev, “Method of investigation of the stress-strain state of surface layer of machine elements from a sintered nonuniform material,” Appl. Mechan. Mater., 486, 32 – 35 (2014).CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC 2017

Authors and Affiliations

  1. 1.FGBOU VO Moscow State Technological University StankinMoscowRussia
  2. 2.SaTCIP Publisher LtdVrnyachka BanyaSerbia

Personalised recommendations