A method of designing ventilation spaces in the case of transfer of powdery materials with enhanced autohesion properties is developed. Free falling streams of conglomerates and their flows in an impermeable trough are considered. The results obtained are useful in the design of efficient ventilation systems with reduced power requirements.
Similar content being viewed by others
References
O. A. Averkova, V. Yu. Zorya, I. N. Logachev, et al., “Numerical simulation of air currents at the inlet to slot leaks of ventilation shelters,” Refractories and Industrial Ceramics, 51(3), 177 – 182 (2010).
K. I. Logachev and N. M. Anzheurov, “Flow analysis of slittype suction ports shielded with slender visors,” Refractories and Industrial Ceramics, 44(3), 145 – 148 (2002).
N. M. Anzheurov and O. A. Averkova, “Software for computing dusty air flows in ventilation systems,” Refractories and Industrial Ceramics, 49(3), 229 – 234 (2008).
O. A. Averkova, I. N. Logachev, and K. I. Logachev, “Modeling separation of flow at the inlet to slit leakages of ventilation shelters,” Novye Ogneupory, No. 10, 56 – 60 (2012).
I. N. Logachev, K. I. Logachev, and O. A. Averkova, “Methods and means of reducing the power requirements of ventilation systems in the transfer of granular materials,” Novye Ogneupory, No. 6, 66 – 70 (2013).
I. N. Logachev, K. I. Logachev, V. Yu. Zorya, et al., “Modeling separated flows near a suction slit,” Vychislitel. Metody i Programmirovanie, 11(1), 43 – 52 (2010).
I. N. Lochev, K. I. Logachev, and O. A. Averkova, “Mathematical modeling of separated currents at the inlet to a shielded planar channel,” Vychislitel. Metody i Programmirovanie, 11(1), 68 – 77 (2010).
I. N. Logachev, K. I. Logachev, and O. A. Averkova, “Mathematical modeling of jet flow of air at the inlet to a planar channel with visor and impermeable screen,” Vychislitel. Metody i Programmirovanie, 11(2), 160 – 167 (2010).
O. A. Averkova, I. N. Logachev, and K. I. Logachev, “Modeling potential currents with unknown boundaries on the basis of stationary discrete vortices,” Vychislitel. Metody i Programmirovanie, 12(2), 213 – 219 (2011).
O. A. Averkova, I. N. Logachev, and K. I. Logachev, “Modeling separation of flow at the inlet to suction channels in a region with slits,” Vychislitel. Metody i Programmirovanie, 13(2), 298 – 306 (2012).
O. A. Averkova, I. N. Logachev, K. I. Logachev, et al., “Laws of separated flow at the inlet to an overflow channel with shields,” Uchen. Zap. TsAGI, 44(2), 33 – 44 (2013).
I. I. Afanas’ev, I. N. Logachev, V. A. Minko, et al., Dedusting of Air at Factories in Mining Concentration Combines [in Russian], Nedra, Moscow (1972), 184 pp.
O. D. Neykov, I. N. Logachev, V. A. Minko, et al., Ventilation and Dedusting of Air in the Production of Powders [in Russian], Metallurgiya, Moscow (1981), 192 pp.
V. Ordinants, Efficiency of suction of dusty air from shelters (translated from German), Chernye Metally, No. 4, 24 – 25 (1975).
N. M. Anzheurov and I. N. Logachev, Optical volumes of ventilation of transfers of agglutinating powders, Vest. BGTU im. Shukhova, 10 – 15 (2003).
The present study was carried out with the support of the Council on Grants of the President of the Russian Federation (Project MK-103.2014.1) and the Program of Strategic Development of the Shukhov State Technological University (Belgograd) (Project No. A-10/12).
Author information
Authors and Affiliations
Corresponding author
Additional information
1Conclusion. Parts 1 – 4 of the article were published in Nos. 2, 4, 6, and 8 of the journal for 2014. The enumeration of the figures and formulas from Parts 1 – 4 are continued in the present part.
Translated from Novye Ogneupory, No. 12, pp. 51 – 54, December, 2014.
Rights and permissions
About this article
Cite this article
Logachev, I.N., Logachev, K.I. & Averkova, O.A. Methods of Reducing the Power Requirements of Ventilation Systems. Part 5. Design of Ventilation Spaces in Transfer of Powder-Like Autohesion Materials1 . Refract Ind Ceram 55, 581–585 (2015). https://doi.org/10.1007/s11148-015-9769-5
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11148-015-9769-5