Skip to main content
Log in

Removal of methyl orange dye from simulated wastewater by electrocoagulation technique using Taguchi method: kinetics and optimization approaches

  • Published:
Reaction Kinetics, Mechanisms and Catalysis Aims and scope Submit manuscript

Abstract

Electrocoagulation method is carried out to remove methyl orange from synthetic wastewater using iron-iron electrodes as anode and cathode. Effects of several experimental parameters treatment of methyl orange (MO) dye removal such as pH, initial concentration, current density and electrode's distance have been studied. The Taguchi method using \(L_{16} {\text{orthogonal array }}\) experimental design was applied to optimize the experimental operating conditions that varied at four levels, initial pH (4–10), current density (1–4 mA/cm2), electrode distance (0.5–1.5 cm), and initial concentration (25–100 mg/L), while the removal efficiency (%R) was considered as the response variable. The Taguchi method based on the average S/N graph method, in combination with analysis of variance (ANOVA), was applied to determine the significant parameters that affect the dye removal. The optimum conditions for removal of MO were determined to be initial concentration (25 mg/L), electrode distance (0.5 cm), pH (8), and current density (3 mA/cm2). The Acidity pH factor represents the most significant factor affecting on removal of MO. The optimum response variables are 97.19 and 97.24% for observed and predicted values, respectively at 39.7575 S/N ratio. As a result, an excellent removal of methyl orange dye from wastewater was attained depending upon the best parametric conditions that obtained from Taguchi method.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3

Similar content being viewed by others

References

  1. Zaroual Z, Azzi M, Saib N, Chainet E (2006) Contribution to the study of electrocoagulation mechanism in basic textile effluent. J Hazard Mater B 131:73–78

    Article  CAS  Google Scholar 

  2. Duan X, Wu P, Pi K, Zhang H, Liu D, Gerson AR (2018) Application of modified electrocoagulation for efficient color removal from synthetic methylene blue wastewater. Int J Electrochem Sci 13:5575–5588

    Article  CAS  Google Scholar 

  3. Aref S (2019) Application of electrocoagulation process for the removal of acid orange 5 in synthetic wastewater. Iran J Chem Chem Eng 38:113–119

    Google Scholar 

  4. Arega Y, Chavan RB (2018) Electrocoagulation followed by ion exchange or membrane separation techniques for recycle of textile wastewater. Adv Res Test Eng 3:1–12

    Google Scholar 

  5. Abbas S, Ali WH (2018) Electrocoagulation technique used to treat wastewater: a review. Am J Eng Res 7:74–88

    Google Scholar 

  6. Nasser M, Alaa MS, Nader BF (2016) Removal of reactive red 24 dye by clean electrocoagulation process using iron and aluminum electrodes. J Chem Eng Proc Technol 7:1–7

    Google Scholar 

  7. Borislav N, Miomir GP, Tijana D (2017) Electrocoagulation of textile wastewater containing a mixture of organic dyes by iron electrode. J Electrochem Sci Eng 7:103–110

    Article  CAS  Google Scholar 

  8. Behnaz N, Mohammad M, Reza A, Amin D, Hamed B (2018) Removal of reactive black 5 dye from aqueous solutions by coupled electrocoagulation and bio-adsorbent process. Electron Phys 10:7086–7094

    Article  Google Scholar 

  9. Irki S, Ghernaout D, Naceur MW, Alghamdi A, Aichouni M (2018) Decolorizing methyl orange by Fe-electrocoagulation process—a mechanistic insight. Int J Environ Chem 2:18–28

    Article  Google Scholar 

  10. Irki S, Ghernaout D, Naceur MW, Alghamdi A, Aichouni M (2018) Decolorization of methyl orange (MO) by electrocoagulation (EC) using iron electrodes under a magnetic field (MF). II. Effect of connection mode. World J Appl Chem 3:56–64

    Article  Google Scholar 

  11. Holkar CR, Jadhav AJ, Pinjari DV, Mahamuni NM, Pandit AB (2016) A critical review on textile wastewater treatments: possible approaches. J Environ Manag 182:351–366

    Article  CAS  Google Scholar 

  12. Haque Y, Jun JW, Jhung SH (2011) Adsorption removal of methyl orange and methylene blue from aqueous solution with a metal-organic framework material, iron terephthalate (MOF-235). J Hazard Mater 185:507–511

    Article  CAS  PubMed  Google Scholar 

  13. Sriprom P, Krobthong W, Assawasaengrat P (2020) Investigation of important parameters for photo-Fenton degradation of methyl orange over Fe/TiO2 catalyst. Energy Rep 6:731–736

    Article  Google Scholar 

  14. Mohammad AT, Abdulhameed AS, Jawad AH (2019) Box-Behnken design to optimize the synthesis of new crosslinked chitosan-glyoxal/TiO2 nanocomposite: methyl orange adsorption and mechanism studies. Int J Biol Macromol 126:98–109

    Article  CAS  Google Scholar 

  15. Yang C, Wang D, Qian T (2014) The Synthesis of NdFeB magnetic activated carbon and its application in degradation of azo dye methyl orange by Fenton-like process. J Taiwan Inst Chem E 45:2584–2589

    Article  CAS  Google Scholar 

  16. Gatsios E, Hahladakis JN, Gidarakos E (2015) Optimization of electrocoagulation (EC) process for the purification of a real industrial wastewater from toxic metals. J Environ Manag 145:117–127

    Article  CAS  Google Scholar 

  17. Rezael H, Haghshenasfard M, Moheb A (2017) Optimization of dye adsorption using Fe3O4 nanoparticles encapsulated with alginate beads by Taguchi method. Adsorpt Sci Technol 35:55–71

    Article  CAS  Google Scholar 

  18. Hafiidz Mohammad Fauzi A, Aishah Saidina Amin N (2013) Optimization of oleic acid esterification catalyzed by ionic liquid for green biodiesel synthesis. Energy Convers Manag 76:818–827

    Article  CAS  Google Scholar 

  19. Lee HV, Yunus R, Juan JC et al (2011) Process optimization design for jatropha-based biodiesel production using response surface methodology. Fuel ProcessTechnol 92:2420–2428

    Article  CAS  Google Scholar 

  20. Bouguerra N, Bouaziz M (2022) Optimization of a novel method for the conversion of tyrosol to hydroxytyrosol via catalytic process using statistical experimental design: kinetic study. Reac Kinet Mech Cat 135:201–217

    Article  CAS  Google Scholar 

  21. Ghanim AN (2016) Application of Taguchi method for electro-fenton degradation of SDBS anionic surfactant. Glob NEST J 18:79–88

    Article  CAS  Google Scholar 

  22. Sorayyaei S, Raji F, Rahbar-Kelishami A, Ashrafizadeh SN (2021) Combination of electrocoagulation and adsorption processes to remove methyl orange from aqueous solution. Environ Technol Innov 24:102018

    Article  CAS  Google Scholar 

  23. Irki S, Ghernaout D, Naceur MW (2017) Decolourization of Methyl Orange (MO) by electrocoagulation (EC) using iron electrodes under a magnetic field (MF). Desalin Water Treat 79:368–377

    Article  CAS  Google Scholar 

  24. Irki S, Ghernaout D, Naceur MW, Alghamdi A, Aichouni M (2018) Decolorizing methyl orange by Fe-electrocoagulation process—a mechanistic insight. Int J Environ Chem 2:18–28

    Article  Google Scholar 

  25. Ma H, Wang B, Luo X (2007) Studies on degradation of methyl orange wastewater by combined electrochemical process. J Hazard Mater 149(2):492–498

    Article  CAS  PubMed  Google Scholar 

  26. Ghernaout D (2018) Electrocoagulation process: achievements and green perspectives. Colloid Surf Sci 3:1–5

    Article  Google Scholar 

  27. Majdi MR, Danaee I, Nikmanesh S (2016) Kinetic and thermodynamic investigations on the electrocoagulation of methyl orange from aqueous solution using aluminum electrodes. Commun 48:628–635

    Google Scholar 

  28. Liu Y, Li C, Bao J, Wang X, Yu W, Shao L (2022) Degradation of azo dyes with different functional groups in simulated wastewater by electrocoagulation. Water 14(1):123

    Article  CAS  Google Scholar 

  29. Asaithambi P, Beyene D, Abdul Aziz AR, Alemayehu E (2018) Removal of pollutants with determination of power consumption from landfill leachate wastewater using an electrocoagulation process: optimization using response surface methodology (RSM). Appl Water Sci 8:1–12

    Article  CAS  Google Scholar 

  30. Aziz S, Abrishamkar M, Kazemian H (2011) Using of Taguchi robust design method to optimize effective parameters of methylene blue adsorption on ZSM-5 zeolite. Asian J Chem 23:100–104

    Google Scholar 

  31. Ozbay V, Arsalan A, Cebi E (2018) Optimization of process variables for treatment of food industry effluents by electrocoagulation. Global NEST J 20:551–557

    Article  CAS  Google Scholar 

  32. Pundir R, Chary GH, Dastidar MG (2018) Application of Taguchi method for optimizing the process parameters for the removal of copper and nickel by growing Aspergillus sp. Water Resour Ind 20:83–92

    Article  Google Scholar 

  33. Huda N, Raman AA, Bello MM, Ramesh S (2017) Electrocoagulation treatment of raw landfill leachate using iron-based electrodes: effects of process parameters and optimization. J Environ Manag 204:75–81

    Article  CAS  Google Scholar 

  34. Yousefi Z, Zafarzadah A, Ghezel A (2018) Application of Taguchi’s experimental design method for optimization of Acid red 18 removal by electrochemical oxidation process. Environ Health Eng Manag J 5:241–248

    Article  CAS  Google Scholar 

  35. Sahithi K, Sujatha V, Sridevi V (2015) Removal of COD from textile effluent using electrocoagulation: statistical design and modeling. Int J Eng Res Technol 4:78–82

    Google Scholar 

  36. Darban A, Shahedi A, Taghipour F, Jamshidi-Zanjani AJCOIE (2020) A review on industrial wastewater treatment via electrocoagulation processes. Curr Opin Electrochem 22:154–169

    Article  CAS  Google Scholar 

  37. Gilavas E, Medina J, Dobrosz-Gómez I, Gómez-Garcia MA (2014) Statistical optimization of industrial textile wastewater treatment by electrochemical methods. J Appl Electrochem 44:1421–1430

    Article  CAS  Google Scholar 

  38. Aleboyeh A, Daneshvar N, Kasiri MB (2008) Optimization of C.I. Acid Red 14 azo dye removal by electrocoagulation batch process with response surface methodology. Chem Eng Process 47:827–832

    Article  CAS  Google Scholar 

  39. Mohammadi MJ, Salari J, Takdastan A, Farhadi M, Javanmardi P, Yari AR, Dobaradaran S, Almasi H, Rahimi SJD, Treatment W (2017) Removal of turbidity and organic matter from car wash wastewater by electrocoagulation process. Desalin Water Treat 68:122–128

    Article  CAS  Google Scholar 

  40. Fuat Ö (2018) Treatment of oily wastewater by electrocoagulation process and optimization of the experimental conditions using Taguchi method. Cumhuriyet Sci J 39:1127–1135

    Google Scholar 

  41. Zabihollah Y, Ali Z, Abdolaziz G (2018) Application of Taguchi’s experimental design method for optimization of Acid Red 18 removal by electrochemical oxidation process. Environ Health Eng Manag J 5:1–9

    Google Scholar 

  42. Fuat O (2016) Optimization of operational parameters of electrocoagulation process for real textile wastewater treatment using Taguchi experimental design method. Desalin Water Treat 57:1–11

    Google Scholar 

  43. Abdalhadi D, Kurta U (2015) Treatment of raw tannery wastewater by electrocoagulation technique: optimization of effective parameters using Taguchi method. Desalin Water Treat 57:1–12

    Google Scholar 

  44. Ghani JA, Jamaludin H, Rahman MNA, Deros BM (2013) Philosophy of Taguchi approach and method in disgn of experiment. Asian J Sci Res 6(1):27–37

    Article  Google Scholar 

  45. Wided B, Khaled B, Elimame E, Mouna L, Be´chir H, (2015) Optimization of electrocoagulation operating parameters and reactor design for zinc removal: application to industrial Tunisian wastewater. Desalin Water Treat 56:1–9

    CAS  Google Scholar 

  46. Violetta K, Krzysztof B, Maciej T, Agnieszka S, Josef J, Aleksander S, Adam S, Andrzej B (2019) Taguchi method and response surface methodology in the treatment of highly contaminated tannery wastewater using commercial potassium ferrate. Materials 12:1–19

    Google Scholar 

  47. Asghari A, Kamalabadi M, Farzinia H (2012) Electrochemical removal of methylene blue from aqueous solutions using taguchi experimental design. Chem Biochem Eng Q 26:145–154

    CAS  Google Scholar 

  48. Asaithambi P, Govindarajan R, Yesuf MB, Selvakumar P, Alemayehu E (2020) Enhanced treatment of landfill leachate wastewater using sono (US)-ozone (O3)–electrocoagulation (EC) process: role of process parameters on color, COD and electrical energy consumption. Process Saf Environ Prot 142:212–218

    Article  CAS  Google Scholar 

  49. Ebba M, Asaithambi P, Alemayehu E (2021) Investigation on operating parameters and cost using an electrocoagulation process for wastewater treatment. Appl Water Sci 11(11):1–9

    Article  CAS  Google Scholar 

  50. Dalvand A, Gholami M, Joneidi A, Mahmoodi NM (2011) Dye removal, energy consumption and operating cost of electrocoagulation of textile wastewater as a clean process. Clean Soil Air Water 39(7):665–672

    Article  CAS  Google Scholar 

  51. Kobya M, Demirbas E (2015) Evaluations of operating parameters on treatment of can manufacturing wastewater by electrocoagulation. J Water Process Eng 8:64–74

    Article  Google Scholar 

  52. Yildiz YŞ, Koparal AS, İrdemez Ş, Keskinler B (2007) Electrocoagulation of synthetically prepared waters containing high concentration of NOM using iron cast electrodes. J Hazard Mater 139(2):373–380

    Article  CAS  PubMed  Google Scholar 

  53. Song S, He Z, Qiu J, Xu L, Chen J (2007) Ozone assisted electrocoagulation for decolorization of CI Reactive Black 5 in aqueous solution: an investigation of the effect of operational parameters. Sep Purif Technol 55(2):238–245

    Article  CAS  Google Scholar 

  54. SenthilKumar P, Umaiyambika N, Gayathri R (2010) Dye removal from aqueous solution by electrocoagulation process using stainless steel electrodes. Environ Eng Manag J EEMJ 9(8):1031–1037

    Article  CAS  Google Scholar 

  55. Mollah MYA, Schennach R, Parga JR, Cocke DL (2001) Electrocoagulation (EC)—science and applications. J Hazard Mater 84(1):29–41

    Article  CAS  PubMed  Google Scholar 

  56. Vasudevan S, Lakshmi J, Jayaraj J, Sozhan G (2009) Remediation of phosphate-contaminated water by electrocoagulation with aluminium, aluminium alloy and mild steel anodes. J Hazard Mater 164(2–3):1480–1486

    Article  CAS  PubMed  Google Scholar 

  57. Al-Shannag M, Al-Qodah Z, Bani-Melhem K, Qtaishat MR, Alkasrawi M (2015) Heavy metal ions removal from metal plating wastewater using electrocoagulation: Kinetic study and process performance. Chem Eng J 260:749–756

    Article  CAS  Google Scholar 

  58. Attour A, Touati M, Tlili M, Amor MB, Lapicque F, Leclerc JP (2014) Influence of operating parameters on phosphate removal from water by electrocoagulation using aluminum electrodes. Sep Purif Technol 123:124–129

    Article  CAS  Google Scholar 

  59. Chen S, Shi Y, Wang W, Li Z, Gao J, Bao K et al (2014) Phosphorus removal from continuous phosphate-contaminated water by electrocoagulation using aluminum and iron plates alternately as electrodes. Sep Sci Technol 49(6):939–945

    Article  CAS  Google Scholar 

  60. Ince M (2013) Treatment of manganese-phosphate coating wastewater by electrocoagulation. Sep Sci Technol 48(3):515–522

    Article  CAS  Google Scholar 

  61. Lacasa E, Canizares P, Saez C, Fernandez FJ, Rodrigo MA (2011) Electrochemical phosphates removal using iron and aluminium electrodes. Chem Eng J 172(1):137–143

    Article  CAS  Google Scholar 

  62. İrdemez Ş, Demircioğlu N, Yıldız YŞ, Bingül Z (2006) The effects of current density and phosphate concentration on phosphate removal from wastewater by electrocoagulation using aluminum and iron plate electrodes. Sep Purif Technol 52(2):218–223

    Article  CAS  Google Scholar 

  63. İrdemez Ş, Demircioğlu N, Yildiz YŞ (2006) The effects of pH on phosphate removal from wastewater by electrocoagulation with iron plate electrodes. J Hazard Mater 137(2):1231–1235

    Article  PubMed  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Anees A. Khadom.

Ethics declarations

Conflict of interest

Authors declare that no conflict of interests.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Abbas, S.H., Younis, Y.M., Rashid, K.H. et al. Removal of methyl orange dye from simulated wastewater by electrocoagulation technique using Taguchi method: kinetics and optimization approaches. Reac Kinet Mech Cat 135, 2663–2679 (2022). https://doi.org/10.1007/s11144-022-02269-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11144-022-02269-9

Keywords

Navigation