Arc-melted Ti100–xMo2Alx alloys (where x is 44, 46, 48, and 50 at.% Al) that were produced from pure components were examined by X-ray diffraction and scanning electron microscopy with electron microprobe analysis (SEM/EDX). The melting points and solid-phase transformations were studied by differential thermal analysis (DTA) and the mechanical properties by fracture toughness, bending, and compression tests. The CALPHAD approach was used for thermodynamic calculation of phase equilibria in the composition region under study. The cast alloys mainly consist of a lamellar structure formed by lamellas of γ-TiAl and α2-Ti3Al phases with submicron thickness and a cubic Ti55Mo4–6Al39–40 phase of A2 type (β) or B2 type (β0). In the γ-TiAl-based alloys, molybdenum behaves as a low-melting dopant, enriching the grain periphery. The standard mechanical characteristics of the alloys were determined and their structural sensitivity was analyzed. All studied alloys demonstrate excellent high-temperature strength. The yield stress is 400–600 MPa in the temperature range 20–750°C. The strength slightly increases at 300 and 600°C under dynamic strain ageing. The strain hardening parameters were established over a wide range of test temperatures. The temperature dependence of the strain hardening coefficient and strain hardening index was analyzed for alloys in different phase and structural states. In the temperature range from 20 to 600°C, the strain hardening index and coefficient were found to vary slightly. The strain hardening index increased from n = 0.6 to n = 0.95 with aluminum content changing from 44 to 50 at.%, which indicates that the strain hardening mechanism changes with variation in the alloy phase constituents.
Similar content being viewed by others
References
S. Das, J.C. Mishurda, W.P. Allen, J.H. Perepezko, and L.S. Chumbley, “Development of a (γ + β0) lamellar microstructure in a Ti45Al50Mo5 alloy,” Scr. Metall. Mater., No. 28, 489–494 (1993).
F.-S. Sun, C.-X. Cao, M.-G. Yan, and S.-E. Kim, “Alloying mechanism of β stabilizers in a TiAl alloy,” Metall. Mater. Trans. A, 32A, 1573–1589 (2001).
I.S. Jung, H.S. Jang, M.H. Oh, J.H. Lee, and D.M. Wee, “Microstructure control of TiAl alloys containing β stabilizers by directional solidification,” Mater. Sci. Eng. A, 329–331, 13–18 (2002).
F. Appel, J.D.H. Paul, and M. Oehring, Gamma Titanium Aluminide Alloys: Science and Technology, Wiley–VCH Verlag GmbH&Co. KGaA, Weinheim (2011), p. 745.
R.K. Gupta, Bhanu Pant, and P. P. Sinha, “Theory and practice of γ + α2 Ti aluminide: A review,” Trans. Indian Inst. Met., 67, No. 2, 143–165 (2014).
S. Mayer, P. Erdely, F. D. Fischer, D. Holec, M. Kastenhuber, T. Klein, and H. Clemens, “Intermetallic β- solidifying γ-TiAl based alloys—from fundamental research to application,” Adv. Mater., 19, 1600735, 1– 27 (2017).
H. Clemens, W. Wallgram, S. Kremmer, V. Güther, A. Otto, and A. Bartels, “Design of novel β-solidifying TiAl alloys with adjustable β/B2-phase fraction and excellent hot-workability,” Adv. Eng. Mater., 10, No. 8, 707–713 (2008).
H. Clemens and S. Mayer, “Design, processing, microstructure, properties, and applications of advanced intermetallic TiAl alloys,” Adv. Eng. Mater., 15, 191–215 (2013).
T. Klein, L. Usategui, B. Rashkova, M.L. Nó, J. San Juan, H. Clemens, and S. Mayer, “Mechanical behavior and related microstructural aspects of a nano-lamellar TiAl alloy at elevated temperatures,” Acta Mater., 128, 440–450 (2017).
S. Mayer, M. Kastenhuber, and H. Clemens, “Advanced titanium aluminides—how to improve the creep resistance via compositional and microstructural optimization,” Mater. Sci. Forum, 941, 1484–1489 (2018).
Ju. A. Kocherzhinsky, “Differential thermocouple up to 2450°C and thermographic investigations of refractory silicide,” in: Proc. Third ICTA (Davos). Thermal Analysis (Vol. 1), Birkhäuser Verlag, Basel (1971), pp. 549–559.
Ju.A. Kocherzhinsky, E.A. Shishkin, and V.I. Vasilenko, “DTA apparatus with a thermocouple sensor to 2200°C,” in: Phase Diagrams of Metallic Systems [in Russian], Nauka, Moscow (1971), pp. 245–249.
V.T. Witusiewicz, U. Hecht, O.M. Stryzhyboroda, N.I. Tsyganenko, V.M. Voblikov, V.M. Petyukh, and T.Ya. Velikanova, “Thermodynamic re-modelling of the ternary Al–Mo–Ti system based on novel experimental data,” J. Alloys Compd., 749, 1071–1091 (2018).
S.M. Ge, I.I. Kornilov, and E.N. Pylyaeva, “Study of the Ti–Al–Mo phase diagram in the region of titanium-rich alloys,” Zh. Neorg. Khim., No. 8, 366–372 (1963).
I.I. Kornilov, T.T. Nartova, and N. I. Shirokov, “Structure and properties of molybdenum-containing Ti3Al aluminide,” Metalloved. Termoobrab. Met., No. 8, 40–42 (1969).
A.A. Bondar, V.T. Witusiewicz, U. Hecht, M.V. Remez, V.M. Voblikov, N.I. Tsyganenko, Ya.I. Evich, Yu.M. Podrezov, and T.Ya. Velikanova, “Structure and properties of titanium–aluminum alloys doped with niobium and tantalum,” Powder Metall. Met. Ceram., 50, No. 7–8, 397–415 (2011).
M.V. Remez, Yu.M. Podrezov, A.A. Bondar, V.T. Witusiewicz, U. Hecht, V.M. Voblikov, N.I. Tsyganenko, Ya.I. Evich, and T.Ya. Velikanova, “Structure and properties of TiAl-based alloys doped with niobium and chromium,” Powder Metall. Met. Ceram., 55, No. 1–2, 91–108 (2016).
V.T. Witusiewicz, A. A. Bondar, U. Hecht, S. Rex, and T.Y. Velikanova, “The Al–B–Nb–Ti system: III. Thermodynamic re-evaluation of the constituent binary system Al–Ti,” J. Alloys Compd., 465, 64–77 (2008).
Z. Jin and T.R. Bieler, “Mechanical twinning in duplex Ti–48Al–2Nb–2Cr at 1038 K,” Mater. Res. Soc. Symp. Proc., 288, 775–780 (1992).
M. Charpentier, D. Daloz, E. Gautier, G. Lesoult, A. Hazotte, and M. Grange, “Study of microstructure and solute partitioning in a cast Ti–48 Al–2 Cr–2 Nb alloy by quenching during directional solidification technique,” Metall. Mater. Trans. A, 34, No. 10, 2139–2148 (2003).
F. Appel, H. Clemens, and F.D. Fischer, “Modeling concepts for intermetallic titanium aluminides,” Prog. Mater. Sci., 81, 55–124 (2016).
B.A. Greenberg and M.A. Ivanov, “The reasons for the unusual behavior of intermetallics during prestraining experiments,” Metallofiz. Noveish. Tekhnol., 21, No. 7, 55–61 (1999).
V.F. Moiseev, “Effective strain hardening index of metals,” Metallofiz. Noveish. Tekhnol., 23, 387–399 (2001).
V.I. Trefilov (ed.), V.F. Moiseev, E.P. Pechkovskii, I.D. Gornaya, and A.D. Vasiliev, Strain Hardening and Fracture of Polycrystalline Metals [in Russian], Naukova Dumka, Kyiv (1989), p. 256.
V.F. Moiseev, I.D. Gornaya, E.P. Pechkovskii, and V.I. Trefilov, “Some regular patterns of strain hardening of polycrystalline molybdenum alloys,” Probl. Prochn., No. 5, 77–82 (1986).
A.V. Kotko, “Strain hardening of doped titanium alloys,” in: Current Issues of Physical Materials Science: Collected Scientific Papers [in Russian], Inst. Probl. Materialoved. NAN Ukrainy, Kyiv (2013), Issue 22, pp. 94–102.
B.V. Petukhov, “Dynamic strain ageing of materials with Peierls plasticity mechanism,” Zh. Tekh. Fiz., 86, No. 9, 65–71 (2016).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Poroshkova Metallurgiya, Vol. 59, Nos. 7–8 (534), pp. 123–138, 2020.
Rights and permissions
About this article
Cite this article
Remez, M., Podrezov, Y., Bondar, A. et al. Structure and Properties of TiAl-Based Alloys Doped with 2 at.% Mo. Powder Metall Met Ceram 59, 454–466 (2020). https://doi.org/10.1007/s11106-020-00179-w
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11106-020-00179-w