Advertisement

Powder Metallurgy and Metal Ceramics

, Volume 56, Issue 5–6, pp 316–322 | Cite as

Multicriterion Assessment of Wear Resistance of Fe–Mn–C–B Eutectic Coatings Alloyed with Si, Ni, and Cr

  • M. Pashechko
  • J. Montusiewicz
  • K. Dziedzic
  • J. Jozwik
Article

The results of tribological studies on Fe–Mn–C–B eutectic coatings alloyed with Si, Ni, and Cr are presented. The coatings are produced by gas metal arc welding with use of powder wires (2.4 mm in diameter). Multicriterion assessment is used to analyze the tribological properties of the coatings and determine the most wear-resistant one. This assessment involves first a search of Pareto optimum solutions and then compromise solutions with use of the Chebyshev norm. This approach allows choosing the coating that shows the highest abrasive wear resistance among the six eutectic materials under study at a specific load varying from 3 to 15 MPa.

Keywords

wear resistance eutectic coatings multicriterion analysis 

References

  1. 1.
    E. Badisch, C. Katsich, H. Winkelmann, et al., “Wear behavior of hardfaced Fe–Cr–C alloy and austenitic steel under 2-body and 3-body conditions at elevated temperature,” Tribol. Int., 43, No. 7, 1234–1244 (2010).CrossRefGoogle Scholar
  2. 2.
    M. I. Pashechko, “Wear resistance of eutectic coatings of the Fe–Mn–C–B system alloyed with Si, Ni, and Cr,” Mater. Sci., 46, No. 5, 695–701 (2011).CrossRefGoogle Scholar
  3. 3.
    M. V. Kindrachuk, “Thermodynamics of oxidation and tribological analysis of eutectic coatings,” Mater. Sci., 31, No. 2, 273–277 (1996).CrossRefGoogle Scholar
  4. 4.
    M. I. Pashechko, G. S. Ershov, K. Lenik, et al., “Eutectic-gradient wear resistance in materials,” Powder Metall. Met. Ceram., 38, No. 7–8, 340–343 (1999).CrossRefGoogle Scholar
  5. 5.
    G. S. Fox-Rabinovich and G. E. Totten, Self-organization during Friction, Advance Surface Engineered Materials and Systems Design, CRC Taylor and Francis Group, Boca Raton (2006), p. 458.CrossRefGoogle Scholar
  6. 6.
    G. S. Fox-Rabinovich, A. I. Kovalev, L. Sh. Shuster, et al., “On characteristic features of alloying HSS-based deformed compound powder materials with consideration for tool self-organization at cutting. II. Cutting tool friction control due to the alloying of the HSS-based deformed compound powder material,” Wear, 214, 279–286 (1998).CrossRefGoogle Scholar
  7. 7.
    V. G. Novytskyi, V. P. Havryliuk, and D. D. Panasenko, “Effect of tin on the wear resistance and secondary structure of cast composites of the Fe–Cr–Cu–Ti–C system under sliding friction,” Met. Sci. Heat Treat., No. 49, 346–353 (2007).Google Scholar
  8. 8.
    M. Pashechko and K. Lenik, “Segregation of atoms of the eutectic alloy Fe–Mn–C–B–Si–Ni–Cr at friction wear,” Wear, 267, Nos. 5–8, 1301–1304 (2009).CrossRefGoogle Scholar
  9. 9.
    M. I. Pashechko, K. Dziedzic, and M. Barszcz, “Study of the structure and properties of wear-resistant eutectic Fe–Mn–C–B–Si–Ni–Cr coatings,” Powder Metall. Met. Ceram., 52, No. 7–8, 469–476 (2013).CrossRefGoogle Scholar
  10. 10.
    A. Klimpel, Surfacing and Thermal Spraying [in Polish], Wydawnictwo Naukowo-Techniczne, Warsaw (2000), p. 470.Google Scholar
  11. 11.
    M. I. Pashechko and J. Montusiewicz, “Evaluation of the wear resistance of eutectic coatings of the Fe–Mn–C–B system alloyed by Si, Ni, and Cr using multi-criterion analysis,” Mater. Sci., 47, No. 6, 813–821 (2012).CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media, LLC 2017

Authors and Affiliations

  • M. Pashechko
    • 1
  • J. Montusiewicz
    • 1
  • K. Dziedzic
    • 1
  • J. Jozwik
    • 1
  1. 1.Lublin University of TechnologyLublinPoland

Personalised recommendations