Skip to main content
SpringerLink
Log in

Effect of Sintering Duration on Some Properties of Pure Magnesium

  • Published:
Powder Metallurgy and Metal Ceramics Aims and scope

Tribological and physical properties of pure magnesium (Mg) are investigated during sintering for 2, 4, and 6 h at the temperature of 600°C. The pure sintered magnesium is characterized by wear behavior, corrosion, scanning electron microscopy (SEM), X-ray energy dispersive spectroscopy (EDS), X-ray diffraction (XRD), unit weight, water absorption, specific weight, and micro-Vickers hardness testing. XRD analysis of sintered Mg revealed the existence of Mg, MgO, and MgO2 compounds. The hardness of the pure magnesium ranged from 53.8 to 70.4 HV0.1. The wear tests are carried out in a ball-disc arrangement under a dry friction condition at room temperature with an applied load of 5 N and a sliding speed of 0.2 m/sec at a sliding distance of 250 m. The wear surfaces of the Mg samples are analyzed using SEM and EDS. It is observed that the wear rate of pure Mg decreased by 54% when the sintering duration is increased. The corrosion resistance of Mg sintered for 6 h is increased by 36% compared to Mg sintered for 2 h.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8

Similar content being viewed by others

References

  1. B. L. Mordike and T. Ebert, “Magnesium: Properties – applications – potential,” Mater. Sci. Eng. A, 302, 37–45 (2001).

    Article  Google Scholar 

  2. V. I. Semenov, L. Sh. Shuster, C. V. Chertovskıkh, et al., “Tribology of composite materials on the basis of magnesium alloy with powder filler of SiC,” Tribol. Ind., 29, No. 1–2, 37–40 (2007).

    Google Scholar 

  3. H. Fredrich and S. Schumann, “Research for a new age of magnesium in the automotive industry,” J. Mat. Proc. Tech., 117, 276–280 (2001).

    Article  Google Scholar 

  4. I. A. Podchernyaeva, D. Panasyuk, V. Yurechko, and N. Talash, “Spark-deposited coatings on magnesium alloys,” Powder Metall. Met. Ceram., 49, No. 1–2, 55–60 (2010).

    Article  Google Scholar 

  5. H. Furuya, N. Kogiso, S. Matunaga, and K. Senda, “Applications of magnesium alloys for aerospace structure systems,” Mater. Sci. Forum, 350–351, 341–348 (2001).

  6. K. Kondoh, H. Oginuma, and T. Aizawa, “Tribological properties of magnesium composite alloy with in situ synthesized Mg2Si. Dispersoids,” Mater. Trans., 44, No. 4, 524–530 (2003).

    Article  Google Scholar 

  7. L. F. Guleryuz, S. Ozan, D. Uzunsoy, and R. Ipek, “An investigation of the microstructure and mechanical properties of B4C reinforced PM magnesium matrix composites,” Powder Metall. Met. Ceram., 51, Nos. 7– 8, 456–462 (2012)

  8. F. Öztürk and I. Kacar, “Investigation of magnesium alloys and their applications,” Nigde University, J. Sci., 1, No. 1, 12–20 (2012).

  9. S. Virtanen, “Tribological properties of the AZ91D magnesium alloy hardened with silicon carbide and by severe plastic deformation,” Mater. Sci. Eng. B, 176, 1600–1608 (2011).

    Article  Google Scholar 

  10. V. I. Semenov, Y. R. Jeng, S. J. Huang, et al., “Tribological properties of the AZ91D magnesium alloy hardened with silicon carbide and by severe plastic deformation,” J. Fric. Wear, 30, No. 3, 194–198 (2009).

    Article  Google Scholar 

  11. J. Capek and D. Vojtech, “Effect of sintering conditions on the microstructural and mechanical characteristics of porous magnesium materials prepared by powder metallurgy,” Mater. Sci. Eng. C, 35, 21–28 (2014).

    Article  Google Scholar 

  12. N. Li and Y. F. Zheng, “Novel magnesium alloys developed for biomedical application: a review,” J. Mater. Sci. Technol., 29, 489–502 (2013).

    Article  Google Scholar 

  13. K. Kondoh, H. Oginuma, R. Tuzuki, and T. Aizawa, “Magnesium matrix composite with solid-state synthesized Mg2Si dispersoids,” Mater. Transac., 44, No. 4, 611–618 (2013).

    Article  Google Scholar 

  14. A. K. Mondal and S. Kumar, “Dry sliding wear behavior of magnesium alloy based hybrid composites in the longitudinal direction,” Wear, 267, 458–466 (2009).

    Article  Google Scholar 

  15. H. Yamagishi, M. Fukuhara, and A. Chiba, “Determination of the mechanical properties of extruded pure magnesium during tension–tension low-cycle fatigue using ultrasonic testing,” Mater. Transac., 51, No. 11, 2025–2032 (2010).

    Article  Google Scholar 

  16. H. Sun, C. Li, Y. Xie, and W. Fang, “Microstructures and mechanical properties of pure magnesium bars by high ratio extrusion and its subsequent annealing treatment,” Trans Nonferro Metals Soc. China, 22, No. 2, 445–449 (2012).

    Article  Google Scholar 

  17. Z. Li, N. Huang, J. Zhao, and S. J. Zhou, “Microstructure, mechanical and degradation properties of equal channel angular pressed pure magnesium for biomedical application,” Mater. Sci. Technol., 29, No. 2, 140– 147 (2013).

    Article  Google Scholar 

  18. K. W. Guo, “A review of magnesium/magnesium alloys corrosion and its protection,” Rec. Pat. Corr. Sci., 2, 13–21 (2010).

    Article  Google Scholar 

  19. K. K. AjithKumar, U. T. S. Pillai, B. C. Pai, and M. Chakraborty, “Dry sliding wear behavior of Mg–Si alloys,” Wear, 303, No. 1–2, 56–64 (2013).

  20. P. J. Blau and M. Walukas, “Sliding friction and wear of magnesium alloy AZ91D produced by two different methods,” Tribol. Int., 33, No. 8, 573–579 (2000).

    Article  Google Scholar 

  21. A. J. López, P. Rodrigo, B. Torres, and J. Rams, “Dry sliding wear behavior of ZE41A magnesium alloy,” Wear, 271, 2836–2844 (2011).

    Article  Google Scholar 

  22. C. Taltavull, A. J. López, B. Torres, and J. Rams, “Dry sliding wear behavior of laser surface melting treated AM60B magnesium alloy,” Surf. Coat. Technol., 236, 368–379 (2013).

    Article  Google Scholar 

  23. S. Q. Wang, Z. R. Yang, Y. T. Zhao, and M. X. Wei, “Sliding Wear Characteristics of AZ91D Alloy at Ambient Temperatures of 25-200°C,” Tribol. Lett., 39, 39–45 (2010).

    Article  Google Scholar 

  24. I. Gunes, “Wear behaviour of plasma paste boronized of AISI 8620 steel with borax and B2O3 paste mixtures,” J. Mater. Sci. Tech., 29, No. 7, 662–668 (2013).

    Article  Google Scholar 

  25. B. Selcuk, R. Ipek, and M. B. Karamis, “A study on friction and wear behaviour of carburized, carbonitrided and borided AISI 1020 and 5115 steels,” J. Mater. Process Technol., 141, 189–196 (2013).

    Article  Google Scholar 

  26. E. Atik, U. Yunker, and C. Meric, “The effects of conventional heat treatment and boronizing on abrasive wear and corrosion of SAE 1010, SAE 1040, D2 and 304 steels,” Tribol. Int., 36, 155–161 (2003).

    Article  Google Scholar 

  27. I. Gunes and A. Dalar, “Effect of sliding speed on friction and wear behavior of borided gear steels,” J. Balkan Tribol. Assoc., 19, No. 3, 325–339 (2013).

    Google Scholar 

  28. I. Gunes, “Investigation of tribological properties and characterization of borided AISI 420 and AISI 5120 steels,” Trans. Indian Inst. Metals., 67, No. 3, 359–365 (2014).

    Article  Google Scholar 

  29. Y. Qiao, X. Wang, Z. Liu, and E. Wang, “Microstructures, textures and mechanical properties evolution during cold drawing of pure Mg,” Micros. Res., 1, 8–15 (2013).

    Article  Google Scholar 

  30. Y. Chino, M. Kobata, H. Iwasaki, and M. Mabuchi, “Tensile properties from room temperature to 673 K of Mg–0.9 mass% Ca alloy containing Lamella Mg2Ca,” Mat. Trans., 43, No. 10, 2643–2646 (2002).

    Article  Google Scholar 

  31. H. Z. Ye and X. Y. Liu, “Review of recent studies in magnesium matrix composites,” J. Mater. Sci., 3, No. 9, 6153–6171 (2004).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metallurgical and Materials Engineering, Faculty of Technology, Afyon Kocatepe University, Afyonkarahisar, Turkey

    I. Gunes

  2. Department of Civil Engineering, Engineering Faculty, Afyon Kocatepe University, Afyonkarahisar, Turkey

    T. Uygunoglu

  3. Department of Automotive Engineering, Faculty of Technology, Afyon Kocatepe University, 03200, Afyonkarahisar, Turkey

    M. Erdogan

Authors
  1. I. Gunes
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. Uygunoglu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. M. Erdogan
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. Gunes.

Additional information

Published in Poroshkovaya Metallurgiya, Vol. 54, Nos. 3–4 (502), pp. 38–48, 2015.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Gunes, I., Uygunoglu, T. & Erdogan, M. Effect of Sintering Duration on Some Properties of Pure Magnesium. Powder Metall Met Ceram 54, 156–165 (2015). https://doi.org/10.1007/s11106-015-9693-8

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11106-015-9693-8

Keywords

Search

Navigation