Abstract
The structure and properties of the surface layers of metals and coatings in the initial state and after friction contact are examined. Substantial increase in the hardness of surface layers after friction is mainly associated with the formation of nanostructure due to shear strains. Deformation does not noticeably change the properties of surface layers when the nanostructure has been formed in the initial material. The relationship is established between the wear resistance and the following properties of the initial coatings and secondary structures: plasticity, stress relaxation coefficient, and their structural component.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
G. Nicolis and I. Prigozhin, Self-Organization in Nonequilibrium Systems, Wiley, New York (1997), p. 207.
I. I. Garber, “Some patterns in metal structurization during friction,” Trenie i Iznos, 13, No. 6, 1076–1082 (1981).
B. I. Kostetskii, “Structural and energy adaptation of materials during friction,” Trenie i Iznos, 6, No. 2, 850–857 (1985).
V. V. Gorskii, “Formation of oxygen-doped Me-Me′-O alloys in frictional contact of metals,” Trenie i Iznos, 10, No. 3, 452–460 (1989).
W. Oliver and J. Pharr, “An improved technique for determining hardness and elastic modulus using load displacement sensing indentation,” J. Mater. Res., 7, No. 6, 1564–1583 (1992).
V. F. Gorban', E. P. Pechkovskii, A. V. Samelyuk, and S. A. Firstov, “Creep of titanium silicon carbide Ti3SiC2 under microindentation at room temperature,” Metallofiz. Noveish. Tekhnol., 27, No. 3–4, 335–354 (2005).
V. Gorban, N. Bega, and G. Sarzhan, “Study of plastic deformation and hardening in friction surface layers,” Phys. Metals (Overseas Publishers Association), 14, No. 11, 1211–1218 (1995).
A. V. Sergueeva, V. V. Stolyarov, R. S. Valiev, and A. K. Mukherjee, “Advanced mechanical properties of pure titanium with ultrafine grained structure,” Scripta Mat., No. 45, 747–752 (2001).
Yu. V. Borisov, E. A. Astakhov, G. S. Kaplina, et al., “Studying the influences of the structure Fe-V coatings of on their mechanical properties,” in: Proc. Conf. on Materials and Coatings in Extreme Conditions: Research, Application, Environmentally Safe Production and Recycling Technologies (Yalta, September 18–22, 2006) [in Russian], Kiev (2006), pp. 204–205.
V. F. Gorban, V. F. Britun, and I. L. Kossko, “Changes caused in the composition and structure of flame-sprayed chromium coatings by friction due to contact interaction,” Powder Metall. Met. Ceram., 34, No. 5–6, 299–303 (1995).
D. A. Dudko, V. G. Aleshin, A. E. Berg, et al., “The nature of the high hardness of vacuum-deposited chromium,” DAN SSSR, 85, No. 1, 106–109 (1985).
S. A. Firstov, T. G. Rogul', V. L. Svechnikov, et al., “Structure, mechanical behavior, and nanohardness of chromium and molybdenum polycrystalline coatings produced by magnetron sputtering,” Metallofiz. Noveish. Tekhnol., 25, No. 9, 1153–1164 (2003).
Author information
Authors and Affiliations
Corresponding author
Additional information
__________
Translated from Poroshkovaya Metallurgiya, Vol. 47, No. 7–8 (462), pp. 146–155, 2008.
Rights and permissions
About this article
Cite this article
Gorban’, V.F. Instrumental indentation for examining the properties of secondary structures of metals and coatings. Powder Metall Met Ceram 47, 493–499 (2008). https://doi.org/10.1007/s11106-008-9048-9
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11106-008-9048-9