Journal of Nanoparticle Research

, Volume 10, Issue 5, pp 795–814 | Cite as

Stabilization of aqueous nanoscale zerovalent iron dispersions by anionic polyelectrolytes: adsorbed anionic polyelectrolyte layer properties and their effect on aggregation and sedimentation

  • Tanapon Phenrat
  • Navid Saleh
  • Kevin Sirk
  • Hye-Jin Kim
  • Robert D. Tilton
  • Gregory V. Lowry
Research Paper

Abstract

Nanoscale zerovalent iron (NZVI) particles are 5–40 nm sized Fe0/Fe-oxide particles that rapidly transform many environmental contaminants to benign products and are a promising in situ remediation agent. Rapid aggregation and limited mobility in water-saturated porous media limits the ability to deliver NZVI dispersions in the subsurface. This study prepares stable NZVI dispersions through physisorption of commercially available anionic polyelectrolytes, characterizes the adsorbed polymer layer, and correlates the polymer coating properties with the ability to prevent rapid aggregation and sedimentation of NZVI dispersions. Poly(styrene sulfonate) with molecular weights of 70 k and 1,000 k g/mol (PSS70K and PSS1M), carboxymethyl cellulose with molecular weights of 90 k and 700 k g/mol (CMC90K and CMC700K), and polyaspartate with molecular weights of 2.5 k and 10 k g/mol (PAP2.5K and 10K) were compared. Particle size distributions were determined by dynamic light scattering during aggregation. The order of effectiveness to prevent rapid aggregation and stabilize the dispersions was PSS70K(83%) > ≈PAP10K(82%) > PAP2.5K(72%) > CMC700K(52%), where stability is defined operationally as the volume percent of particles that do not aggregate after 1 h. CMC90K and PSS1M could not stabilize RNIP relative to bare RNIP. A similar trend was observed for their ability to prevent sedimentation, with 40, 34, 32, 20, and 5 wt%, of the PSS70K, PAP10K, PAP2.5K, CMC700K, and CMC90K modified NZVI remaining suspended after 7 h of quiescent settling, respectively. The stable fractions with respect to both aggregation and sedimentation correlate well with the adsorbed polyelectrolyte mass and thickness of the adsorbed polyelectrolyte layers as determined by Oshima’s soft particle theory. A fraction of the particles cannot be stabilized by any modifier and rapidly agglomerates to micron sized aggregates, as is also observed for unmodified NZVI. This non-dispersible fraction is attributed to strong magnetic attractions among the larger particles present in the polydisperse NZVI slurry, as the magnetic attractive forces increase as r6.

Keywords

NZVI Nanoscale zerovalent iron particles Polyelectrolyte Dispersion stability Colloid Surface modification Aggregation and sedimentation Steric stabilization Extended DLVO Environmental nanotechnology Groundwater remediation Nanoparticle environmental fate and transport 

Abbreviations

NZVI

Nanoscale zerovalent iron

PSS

Poly(styrene sulfonate)

CMC

Carboxymethyl cellulose

PAP

Polyaspartate

DLVO

Derjaguin–Landau–Verwey–Overbeek

RNIP

Reactive nano-scale iron particles

DLS

Dynamic light scattering

References

  1. Allain C, Cloitre M (1993) The effects of gravity on the aggregation and the gelation of colloids. Adv Colloid Interface Sci 46:129–138CrossRefGoogle Scholar
  2. Bandyopadhyaya R, Nativ-Roth E, Regev O, Yerushalmi-Rozen R (2002) Stabilization of individual carbon nanotubes in aqueous solutions. Nano Lett 2(1):25–28CrossRefGoogle Scholar
  3. Biesheuvel PM (2004) Ionizable polyelectrolyte brushes: brush height and electrosteric interaction. J Colloid Interface Sci 275(1):97–106CrossRefGoogle Scholar
  4. Blokhus AM, Djurhuus K (2006) Adsorption of poly(styrene sulfonate) of different molecular weights on alpha-alumina: effect of added sodium dodecyl sulfate. J Colloid Interface Sci 296:64–70CrossRefGoogle Scholar
  5. Box GEP, Hunter WG, Hunter JS (1978) Statistics for experimenters: an introduction to design, data analysis, and model building. Wiley-Interscience, New YorkGoogle Scholar
  6. Butter K, Bomans PH, Frederik PM, Vroege GJ, Philipse AP (2003) Direct observation of dipolar chains in ferrofluids in zero field using cryogenic electron microscopy. J Phys Condens Matter 15:S1451–S1470CrossRefGoogle Scholar
  7. Chen K-L, Elimelech M (2006) Aggregation and deposition kinetics of fullerene (C-60) nanoparticles. Langmuir 22(26):10994–11001CrossRefGoogle Scholar
  8. Chibowski S, Wisniewska M (2002) Study of electrokinetic properties and structure of adsorbed layers of polyacrylic acid and polyacrylamide at Fe2O3–polymer solution interface. Colloids Surf A 208(1–3):131–145CrossRefGoogle Scholar
  9. Chodanowski P, Stoll S (2001) Polyelectrolyte adsorption on charged particles in the Debye-Hückel approximation. A Monte Carlo approach. Macromolecules 34(7):2320–2328CrossRefGoogle Scholar
  10. Dunphy Guzman KA, Finnegan MP, Banfield JF (2006) Influence of surface potential on aggregation and transport of titania nanoparticles. Environ Sci Technol 40(24):7688–7693CrossRefGoogle Scholar
  11. Duro R, Souto C, Gómez-Amoza JL, Martínez-Pacheco R, Concheiro A (1999) Interfacial adsorption of polymers and surfactants: implications for the properties of disperse systems of pharmaceutical interest. Drug Dev Ind Pharm 25(7):817–829CrossRefGoogle Scholar
  12. Elimelech M, Gregory J, Jia X, Williams R (1995) Particle deposition and aggregation: measurement, modeling, and simulation. Butterworth-Heinemann, BostonGoogle Scholar
  13. Elliott DW, Zhang W-X (2001) Field assessment of nanoscale bimetallic particles for groundwater treatment. Environ Sci Technol 35:4922–4926CrossRefGoogle Scholar
  14. Evans DF, Wennerstrom H (1999) The colloidal domain; where physics, chemistry, biology, and technology meet. Wiley-VCH, New YorkGoogle Scholar
  15. Fleer GJ, Cohen Stuart MA, Scheutjens JMHM, Cosgrove T, Vincent B (1993) Polymers at interfaces. Chapman & Hall, LondonGoogle Scholar
  16. Fritz G, Schadler V, Willenbacher N, Wagner NJ (2002) Electrosteric stabilizatoin of colloidal dispersions. Langmuir 18:6381–6390CrossRefGoogle Scholar
  17. Goddard ED, Vincent B (1984) Polymer adsorption and dispersion stability. ACS, WashingtonGoogle Scholar
  18. Gomez-Lopera SA, Arias JL, Gallardo V, Delgado AV (2006) Colloidal stability of magnetite/poly(lactic acid) core/shell nanoparticles. Langmuir 22(6):2816–2821CrossRefGoogle Scholar
  19. Guan YH, Lath DL, de Graaf T, Lilley THAHB (2003) Moderation of oral bacterial adhesion on saliva-coated hydroxyapatite by polyaspartate. J Appl Microbiol 94:456–461CrossRefGoogle Scholar
  20. Henn KW, Waddill DW (2006) Utilization of nanoscale zero-valent iron for source remediation—A case study. Remediat J 16:57–77CrossRefGoogle Scholar
  21. Hiemenz P, Rajagopalan R (1997) Principles of colloid and surface chemistry. CRC, New YorkGoogle Scholar
  22. Holmberg K, Jonsson B, Kronberg B, Lindman B (2003) Surfactants and polymers in aqueous solution. John Wiley&Sons, Ltd., West SussexGoogle Scholar
  23. Kanel SR, Nepal D, Manning B, Choi H (2007) Transport of surface-modified iron nanoparticle in porous media and application to arsenic(III) remediation. J Nanopart Res 9(5):725–735CrossRefGoogle Scholar
  24. Kim B, Sigmund WM (2004) Functionalized multiwall carbon nanotube/gold nanoparticle composites. Langmuir 20(19):8239–8242CrossRefGoogle Scholar
  25. Liu Y, Lowry GV (2006) Effect of particle age (Fe0 content) and solution pH on NZVI reactivity: H2 evolution and TCE dechlorination. Environ Sci Technol 40(19):6085–6090CrossRefGoogle Scholar
  26. Liu Y, Majetich SA, Tilton RD, Sholl DS, Lowry GV (2005) TCE dechlorination rates, pathways, and efficiency of nanoscale iron particles with different properties. Environ Sci Technol 39(5):1338–1345CrossRefGoogle Scholar
  27. Mays DC, Hunt JR (2005) Hydrodynamic aspects of particle clogging in porous media. Environ Sci Technol 39(2):577–584CrossRefGoogle Scholar
  28. McCurrie RA (1994) Ferromagnetic materials: structure and properties. Academic Press, LondonGoogle Scholar
  29. Nakamura M, Ohshima H, Kondo T (1992) Electrophoretic behavior of antigen- and antibody-carrying latex particles. J Colloid Interface Sci 149(1):241–246CrossRefGoogle Scholar
  30. Napper DH (1983) Polymeric stabilization of colloidal dispersions. Academic Press, New YorkGoogle Scholar
  31. Nurmi JT, Tratnyek PG, Sarathy V, Baer DR, Amonette JE, Pecher K, Wang C, Linehan JC, Matson DW, Penn RL, Driessen MD (2005) Characterization and properties of metallic iron nanoparticles: spectroscopy, electrochemistry, and kinetics. Environ Sci Technol 39(5):1221–1230CrossRefGoogle Scholar
  32. Nylander T (1998) Protein adsorption in relation to solution association and aggregation. In: Malmsten M (eds) Biopolymer at interfaces. Marcel Dekker, New York, pp 409–452Google Scholar
  33. Ohshima H (1994) Electrophoretic mobility of soft particles. J Colloid Interface Sci 163:474–483CrossRefGoogle Scholar
  34. Ohshima H (1995a) Electrophoresis of soft particles. Adv Colloid Interface Sci 62:189–235CrossRefGoogle Scholar
  35. Ohshima H (1995b) Electrophoretic mobility of soft particles. Colloids Surf A 103:249–255CrossRefGoogle Scholar
  36. Ohshima H, Nakamura M, Kondo T (1992) Electrophoretic mobility of colloidal particles coated with a layer of adsorbed polymers. Colloid Polym Sci 270:873–877CrossRefGoogle Scholar
  37. Phenrat T, Saleh N, Sirk K, Tilton RD, Lowry GV (2007) Aggregation and sedimentation of aqueous nanoscale zerovalent iron dispersions. Environ Sci Technol 41(1):284–290CrossRefGoogle Scholar
  38. Ponder SM, Darab JG, Mallouk TE (2000) Remediation of Cr(VI) and Pb(II) aqueous solutions using supported, nanoscale zero-valent iron. Environ Sci Technol 34:2564–2569CrossRefGoogle Scholar
  39. Ramos-Tejada MM, Ontiveros A, Viota JL, Durán JDG (2003) Interfacial and rheological properties of humic acid/hematite suspensions. J Colloid Interface Sci 268(1):85–95CrossRefGoogle Scholar
  40. Romero-Cano MS, Martı´n-Rodrı´guez A, de las Nieves FJ (2001) Electrosteric stabilization of polymer colloids with different functionality. Langmuir 17:3505–3511CrossRefGoogle Scholar
  41. Rosenweig RE (1985) Ferrohydrodynamics. Cambridge University Press, New YorkGoogle Scholar
  42. Saleh N, Phenrat T, Sirk K, Dufour B, Ok J, Sarbu T, Matyjaszewski K, Tilton RD, Lowry GV (2005) Adsorbed triblock copolymers deliver reactive iron nanoparticles to the oil/water interface. Nano Lett 5(12):2489–2494CrossRefGoogle Scholar
  43. Saleh N, Sirk K, Liu Y, Phenrat T, Dufour B, Matyjaszewski K, Tilton RD, Lowry GV (2007) Surface modifications enhance nanoiron transport and NAPL targeting in saturated porous media. Environ Eng Sci 24(1):45–57CrossRefGoogle Scholar
  44. Sato T, Ruch R (1980) Stabilization of colloidal dispersions by polymer. Adsorption Marcel Dekker, New YorkGoogle Scholar
  45. Singh BP, Menchavez R, Takai C, Fuji M, Takahashi M (2005) Stability of dispersions of colloidal alumina particles in aqueous suspensions. J Colloid Interface Sci 291(1):181–186CrossRefGoogle Scholar
  46. Strenge K (1993) Structure formation in disperse systems In: Dobias B (ed) Coagulation and flocculation: theory and applications. Marcel Dekker, New YorkGoogle Scholar
  47. Tsuneda S, Aikawa H, Hayashi H, Hirata A (2004) Significance of cell electrokinetic properties determined by soft-particle analysis in bacterial adhesion onto a solid surface. J Colloid Interface Sci 279:410–417CrossRefGoogle Scholar
  48. Viota JL, de Vicente J, Ramos-Tejada MM, Durán JDG (2004) Electrical double layer and rheological properties of yttria-stabilized zirconia suspensions in solutions of high molecular weight polyacrylic acid polymers. Rheol Acta 43:645–656CrossRefGoogle Scholar
  49. Viota JL, de Vicente J, Duran JDG, Delgado AV (2005) Stabilization of magnetorheological suspensions by polyacrylic acid polymers. J Colloid Interface Sci 284:527–541CrossRefGoogle Scholar
  50. Wang J, Somasundaran P (2005) Adsorption and conformation of carboxymethyl cellulose at solid-liquid interfaces using spectroscopic, AFM and allied techniques. J Colloid Interface Sci 291:75–83CrossRefGoogle Scholar
  51. Wiesner MR, Lowry GV, Alvarez P, Dionysiou D, Biswas P (2006) Assessing the risks of manufactured nanomaterials. Environ Sci Technol A-Pages 40(14):4336–4337Google Scholar
  52. Williams DN, Gold KA, Pulliam Holoman TR, Ehrman SH, Wilson OC (2006) Surface modification of magnetic nanoparticles using gum arabic. J Nanopart Res 8(5):749–753CrossRefGoogle Scholar
  53. Wu L, Shamsuzzoha M, Ritchie SMC (2005) Preparation of cellulose acetate supported zero-valent iron nanoparticles for the dechlorination of trichloroethylene in water. J Nanopart Res 7:469–476CrossRefGoogle Scholar
  54. Xu J, Dozier A, Bhattacharyya D (2005) Synthesis of nanoscale bimetallic particles in polyelectrolyte membrane matrix for reductive transformation of halogenated organic compounds. J Nanopart Res 7:449–467CrossRefGoogle Scholar
  55. Zhang W (2003) Nanoscale iron particles for environmental remediation: an overview. J Nanopart Res 5:323–332CrossRefGoogle Scholar

Copyright information

© Springer Science+Business Media B.V. 2007

Authors and Affiliations

  • Tanapon Phenrat
    • 1
  • Navid Saleh
    • 1
  • Kevin Sirk
    • 2
  • Hye-Jin Kim
    • 1
  • Robert D. Tilton
    • 2
    • 3
  • Gregory V. Lowry
    • 1
    • 2
  1. 1.Department of Civil & Environmental EngineeringCarnegie Mellon UniversityPittsburghUSA
  2. 2.Department of Chemical EngineeringCarnegie Mellon UniversityPittsburghUSA
  3. 3.Department of Biomedical EngineeringCarnegie Mellon UniversityPittsburghUSA

Personalised recommendations