Skip to main content
SpringerLink
Log in

Design of characteristics of air-pressure-controlled hydraulic shock absorbers in an intercity bus

  • Published:
Multibody System Dynamics Aims and scope Submit manuscript

Abstract

The air-pressure-controlled shock absorber is capable of changing its damping force depending on the air pressure in the air springs. Due to the possibility of improving dynamic properties of all vehicles that use the axles’ air suspensions, BRANO Inc. (the Czech producer of shock absorbers) started to develop semi-active air-pressure-controlled hydraulic telescopic shock absorbers. The SOR C 12 intercity bus is the reference vehicle for which the research and development of controlled shock absorbers is done and on which the shock absorbers are verified. Force–velocity characteristics of the controlled shock absorbers of the axles’ air suspension were designed on the basis of results of computer simulations with the bus multibody models created in the alaska simulation tool. Multibody models of an empty vehicle, a fully loaded vehicle and three variants of a partly loaded vehicle were created. For each weight of the bus two multibody models of various levels of complexity were created. Since the bus multibody models should be used especially for designing force–velocity characteristics of air-pressure-controlled shock absorbers, great attention (in the framework of the possibilities of multibody dynamics) was paid to the correct interpretation of the real behaviour of hydraulic shock absorbers and air springs of the axles’ suspension. As a criterion for the design of the optimum force–velocity characteristics of the controlled shock absorbers, the maximum similarity of the dynamic responses of multibody models of the bus of all the considered weights to dynamic response of the reference multibody model of the bus with the same load as during the experimental measurements on the real vehicle (approx. 71.5% of the maximum loaded vehicle weight) was chosen. In the course of the measurements the non-controlled shock absorbers’ characteristics were optimally tuned for that vehicle weight. Time histories of relative deflections of the axles’ air springs determined during the simulations of the vehicle running over the vertical artificial obstacle were compared. The approach based on the evaluation of the correlation coefficient of two time series was used for the evaluation of the dynamic responses accordance.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Vlk, F.: Dynamics of Motor Vehicles. VLK Publishing House, Brno (2000) (in Czech)

    Google Scholar 

  2. Lauwerys, C., Swevers, J., Sas, P.: Linear control of car suspension using nonlinear actuator control. In: Sas, P., van Hal, B. (eds.) ISMA 2002 International Conference on Noise & Vibration Engineering, Katholieke Universiteit Leuven, Leuven, Belgium, pp. 55–62 (2002)

  3. Kitching, K.J., Cole, D.J., Cebon, D.: Performance of a semi-active damper for heavy vehicles. ASME J. Dyn. Syst. Meas. Control 122, 498–506 (2000)

    Article  Google Scholar 

  4. Kitching, K.J., Cole, D.J., Cebon, D.: The development of a heavy vehicle semi-active damper. In: International Symposium on Advanced Vehicle Control AVEC’96, Aachen, Germany (1996)

  5. Karnopp, D.: Permanent magnet linear motors used as variable mechanical dampers for vehicle suspension. Veh. Syst. Dyn. 18, 187–200 (1989)

    Article  Google Scholar 

  6. Choi, S.B., Choi, Y.T., Chang, E.G., Han, S.J., Kim, C.S.: Control characteristics of a continuously variable ER damper. Mechatronics 8, 143–161 (1998)

    Article  Google Scholar 

  7. Choi, S.B., Han, S.S.: H ∞ control of electrorheological suspension system subjected to parameter uncertainties. Mechatronics 13, 639–657 (2003)

    Article  Google Scholar 

  8. Sims, N.D., Peel, D.J., Stanway, R., Johnson, A.R., Bullough, W.A.: The electrorheolgical long-stroke damper: A new modeling technique with experimental validation. J. Sound Vib. 229, 207–227 (2000)

    Article  Google Scholar 

  9. Guglielmino, E., Edge, K.A.: A controlled friction damper for vehicle applications. Control Eng. Pract. 12, 431–444 (2004)

    Article  Google Scholar 

  10. Xia, P.Q.: An inverse model of MR damper using optimal neural network and system identification. J. Sound Vib. 266, 1009–1023 (2003)

    Article  Google Scholar 

  11. Holdmann, P., Holle, M.: Possibilities to improve the ride and handling performance of delivery trucks by modern mechatronic systems. J. Soc. Automot. Eng. Jpn. 20, 505–510 (1999)

    Google Scholar 

  12. Etman, L.F.P.: Optimization of multibody systems using approximation concepts. Ph.D. thesis, Eindhoven University of Technology, Eindhoven (1997)

  13. Naudé, A.F., Snyman, J.A.: Optimisation of road vehicle passive suspension systems. Part 1. Optimisation algorithm and vehicle model. Appl. Math. Model. 27, 249–261 (2003)

    Article  MATH  Google Scholar 

  14. Naudé, A.F., Snyman, J.A.: Optimisation of road vehicle passive suspension systems. Part 2. Qualification and case study. Appl. Math. Model. 27, 263–274 (2003)

    Article  MATH  Google Scholar 

  15. Ieluzzi, M., Turco, P., Montiglio, M.: Development of a heavy truck semi-active suspension control. Control Eng. Pract. 14, 305–312 (2006)

    Article  Google Scholar 

  16. Eberhard, P., Piram, U., Bestle, D.: Optimization of damping characteristics in vehicle dynamics. Eng. Optim. 31, 435–455 (1999)

    Article  Google Scholar 

  17. Danesin, D., Vercellone, P., Mastronardi, F., Fenoglio, M., Fornero, A., Velardocchia, M.: Vehicle dynamics with real time damper systems. In: 16th European ADAMS User Conference 2001, Berchtesgaden, Germany (2001)

  18. Valášek, M., Kortüm, W., Šika, Z., Magdolen, L., Vaculín, O.: Development of semi-active road-friendly truck suspensions. Control Eng. Pract. 6, 735–744 (1998)

    Article  Google Scholar 

  19. Maißer, P., Wolf, C.D., Keil, A., Hendel, K., Jungnickel, U., Hermsdorf, H., Tuan, P.A., Kielau, G., Enge, O., Parsche, U., Härtel, T., Freudenberg, H.: alaska, User Manual, Version 2.3. Institute of Mechatronics, Chemnitz (1998)

    Google Scholar 

  20. Polach, P., Hajžman, M.: Approaches to the creation of the intercity SOR bus multibody models. In: Vimmr, J. (ed.) 21st Conference with International Participation Computational Mechanics 2005, FAS UWB, Hrad Nečtiny, Czech Republic, vol. 2, pp. 477–484 (2005) (in Czech)

  21. Mastník, Z.: Test Report No. 5-21-1004/Mz. BRANO Inc., Jablonec nad Nisou (2004) (in Czech)

  22. Hajžman, M., Polach, P.: Hydraulic shock absorbers modelling in trolleybus multibody simulations of running over a large road unevenness. In: Zolotarev, I., Poživilová, A. (eds.) National Conference with International Participation Engineering Mechanics 2004, IT ASCR, Svratka, Czech Republic, CD-ROM T-Hajzman-Michal (2004) (in Czech)

  23. Vlk, F.: Chassis of Motor Vehicles. VLK Publishing House, Brno (2001) (in Czech)

    Google Scholar 

  24. Kopenec, J.: The SOR C10,5 bus virtual prototype. 1st model approach to the real system. Technical Report Multibody System Analysis, Software, Support MSA/SOR/2002/03, Kopřivnice (2002) (in Czech)

  25. Harth, V., Fayet, M., Maiffredy, L., Renou, C.: A modelling approach to tire-obstacle interaction. Multibody Syst. Dyn. 11, 23–39 (2004)

    Article  MATH  Google Scholar 

  26. Holeček, M., Polach, P.: Study of the influence of shape of road surface unevenness on vehicle dynamic response. Research Report ŠKODA RESEARCH Ltd., VYZ 0165/98, Plzeň (1998) (in Czech)

  27. Rektorys, K., et al.: Survey of Applicable Mathematics, vol. 2. Kluwer Academic, Dordrecht (1994)

    Google Scholar 

  28. MATLAB®: Documentation version 7. The MathWorks, Inc. http://www.mathworks.com/ (2004)

Download references

Author information

Authors and Affiliations

  1. Section of Materials and Mechanical Engineering Research, ŠKODA RESEARCH Ltd., Tylova 1/57, 316 00, Plzeň, Czech Republic

    Pavel Polach & Michal Hajžman

Authors
  1. Pavel Polach
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Michal Hajžman
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Pavel Polach.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Polach, P., Hajžman, M. Design of characteristics of air-pressure-controlled hydraulic shock absorbers in an intercity bus. Multibody Syst Dyn 19, 73–90 (2008). https://doi.org/10.1007/s11044-007-9055-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11044-007-9055-5

Keywords

Search

Navigation