Skip to main content
SpringerLink
Log in

Structure of Alloy Ak10m2n After Tensile Plastic Deformation

  • Published:
Metal Science and Heat Treatment Aims and scope

Silumin AK10M2N is studied in a cast condition and after irradiation with a pulsed electron beam (17 keV, 50 J/cm2, 3 pulses, 100 sec, 0.3 sec –1). Elemental and phase compositions of the alloy are determined. Structure and the fracture surfaces after uniaxial tension of flat specimens in an INSTRON 3386 machine at a constant rate are studied by scanning electron microscopy and transmission electron diffraction microscopy. It is shown that irradiation of alloy AK10M2N with a pulsed electron beam is accompanied by fusion of a comparatively thin (up to 100 μm) surface layer. Subsequent high-speed crystallization yields a multiphase submicro- and nanocrystalline structure of cellular crystallization. Cast alloy irradiation with an electron beam increases ultimate strength by a factor of 1.8 and elongation by a factor of 2.2. The main causes of this effect are determined.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  1. W. Yan, W. Chen, S. Zhang, et al., “Evolution of solidification structures and mechanical properties of high-Si Al alloys under permanent magnetic stirring,” Mater. Charact., 157, 109894 (2019).

    Article  CAS  Google Scholar 

  2. A. M. A. Mohamed, A. M. Samuel, et al., “Influence of additives on the microstructure and tensile properties of near-eutectic Al – 10.8% Si cast alloy,” Mater. Design, 30, 3943 – 3957 (2009).

    Article  CAS  Google Scholar 

  3. M. Javidani and D. Larouche, “Application of cast Al – Si alloys in internal combustion engine components,” Int. Mater. Rev., 59(3), 132 – 158 (2014).

    Article  CAS  Google Scholar 

  4. V. S., Zolotorevskiy, N. A. Belov, and M. V. Glazoff, Casting Aluminum Alloys, Elsevier Science, (2007).

  5. M. Okayasu, K. Ota, and S. Takeuchi, “Influence of microstructural characteristics on mechanical properties of ADC12 aluminum alloy,” Mater. Sci. Eng. A, 592. 189 – 200 (2014).

    Article  CAS  Google Scholar 

  6. C.-Y. Jeong, “High temperature mechanical properties of AlSiMg(Cu) alloys for automotive cylinder heads,” Mater. Trans., 54, 588 – 594 (2013).

    Article  CAS  Google Scholar 

  7. S. Hegde and K. N. Prabhu, “Modification of eutectic silicon in Al – Si alloys,” J. Mater. Sci., 43, 3009 – 3027 (2008).

    Article  CAS  Google Scholar 

  8. H. Xia, C. Zhang, P. Lv, et al., “Surface alloying of aluminum with molybdenum by high-current pulsed electron beam,” Nucl. Instruments Methods Phys. Res. Sect. B, Beam Interact. with Mater. Atoms, 416, 9 – 15 (2018).

    Article  CAS  Google Scholar 

  9. S. V. Konovalov, K. V. Alsaraeva, V. E. Gromov, et al., “The influence of electron beam treatment on Al – Si alloy structure destroyed at high-cycle fatigue,” Key Eng. Mater., 675 – 676, 655 – 659 (2016).

  10. V. E. Gromov, Yu. F. Ivanov, S. V. Vorobiev, and S. V. Konovalov, Fatigue of Steels Modified by High Intensity Electron Beams, Cambridge International Science Publishing (2015).

  11. G. Bo, X. Ning, and X. Pengfei, “Shock wave induced nanocrystallization during the high current pulsed electron beam process and its effect on mechanical properties,” Mater. Lett., 237, 180 – 184 (2019).

    Article  Google Scholar 

  12. L. Diankun, G. Bo, Z. Guanglin, et al., “High-current pulsed electron treatment of hypoeutectic Al – 10Si alloy” High Temp. Mater. Proc., 36 (1), 97 100 (2017).

    Google Scholar 

  13. B. Gao, Y. Hao,W. F. Zhuang, et al., “Study on continuous solid solution of Al and Si elements of a high current pulsed electron beam treated hypereutectic Al17.5Si alloy,” Phys. Procedia, 18, 187 – 192 (2011).

    Article  CAS  Google Scholar 

  14. Y. Hao, B. Gao, G. F. Tu, et al., “Improved wear resistance of Al – 15Si alloy with a high current pulsed electron beam treatment,” Nucl. Instruments Methods Phys. Res. Sect. B, Beam Interact. with Mater. Atoms, 269(13), 1499 – 1505 (2011).

    Article  CAS  Google Scholar 

  15. H. Li, L. Zhan, M. Huang, et al., “Investigation on the asymmetric creep ageing behaviour of 2195-T84 Al – Li alloy under different tensile and compressive stress levels,” Intermetallics, 131, 107078 (2021).

    Article  CAS  Google Scholar 

  16. X. X. Zhang, A. Lutz, H. Andrä, et al., “Evolution of microscopic strains, stresses, and dislocation density during in-situ tensile loading of additively manufactured AlSi10Mg alloy,” Int. J. Plasticity, 139, 102946 (2021).

    Article  CAS  Google Scholar 

  17. G. Ozur and D. I. Proskurovsky, “A wide-aperture, low-energy, and high-current electron beam source with a plasma anode based on a reflective discharge,” Instr. Experim. Tech., 48(6), 753 – 760 (2005).

    Article  CAS  Google Scholar 

  18. D. Zaguliaev, S. Konovalov, Y. Ivanov, et al., “Microstructure and microhardness of piston alloy AK10M2N irradiated by pulsed electron beam,” Arch. Foundry Eng., 20(3), 92 – 98 (2020).

    CAS  Google Scholar 

  19. S. Konovalov, D. Zaguliaev, Y. Ivanov, et al., “Modification of AK10M2H alloy surface by intensive pulsed electron beam,” J. Mater. Res. Technol., 9(3), 5591 – 5598 (2020).

    Article  CAS  Google Scholar 

  20. N. A. Belov, S. V. Savcheenko, and A. B. Khvan, Silumin Phase Composition and Structure: Reference Edition [in Russian], MISiS, Moscow (2007).

    Google Scholar 

  21. G. Thomas and M. J. Goringe, Transmission Electron Microscopy of Materials, Wiley, New York (1979).

    Google Scholar 

Download references

Work was conducted with financial support of an RNF grant (project No. 19-79-10059).

Author information

Authors and Affiliations

  1. Siberian State Industrial University, Novokuznetsk, Russia

    K. V. Aksenova, D. V. Zagulyaev & D. S. Yakupov

  2. Tomsk State University of Architecture and Civil Engineering, Tomsk, Russia

    A. A. Klopotov & A. M. Ustinov

  3. Institute of High-Current Electronics of the Siberian Branch of the Russian Academy of Sciences (ISÉ SO RAN), Tomsk, Russia

    Yu. F. Ivanov

Authors
  1. K. V. Aksenova
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. D. V. Zagulyaev
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. A. Klopotov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Yu. F. Ivanov
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. A. M. Ustinov
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. D. S. Yakupov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to K. V. Aksenova.

Additional information

Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 6, pp. 17 – 23, June, 2022.

Rights and permissions

Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Aksenova, K.V., Zagulyaev, D.V., Klopotov, A.A. et al. Structure of Alloy Ak10m2n After Tensile Plastic Deformation. Met Sci Heat Treat 64, 309–315 (2022). https://doi.org/10.1007/s11041-022-00806-w

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11041-022-00806-w

Keywords

Search

Navigation