The study investigates a high-entropy non-equiatomic alloy of the Co – Cr – Fe – Mn – Ni system obtained using wire-arc additive manufacturing (WAAM) technology and subjected to electron beam irradiation (EBI). The strain curves of alloy samples under tension after fabrication and EBI are analyzed. The structure of the fracture surface of the alloy was studied using scanning electron microscopy. The strength and plasticity of the alloy are shown to decrease with an increase in the energy density of the electron beam. This is assumed to be due to the appearance of defects in the structure of the surface layers as a result of elastic stresses arising during high-speed quenching of samples following thermal exposure to an electron beam.
Similar content being viewed by others
References
E. P. George, W. A. Curtin, and C. C. Tasan, “High entropy alloys: A focused review of mechanical properties and deformation mechanisms,” Acta Mater., 188, 435 – 474 (2020).
V. Shivam, J. Basu, V. K. Pandey, et al., “Alloying behaviour, thermal stability and phase evolution in quinary AlCoCrFeNi high entropy alloy,” Adv. Powd. Tech., 29, 2221 – 2230 (2018).
U. L. Ganesh and H. Raghavendra, “Review on the transition from conventional to multi-component-based nano-high-entropy alloys-NHEAs,” J. Therm. Anal. Calor., 139, 207 – 216 (2020).
Y. A. Alshataif, S. Sivasankaran, F. A. Al-Mufadi, et al., “Manufacturing methods, microstructural and mechanical properties evolutions of high-entropy alloy: a review,” Met. Mater. Intern., 26, 1099 – 1133 (2019).
K. C. Cheng, J. H. Chen, S. Stadler, and S. H. Chen, “Properties of atomized AlCoCrFeNi high-entropy alloy powders and their phase-adjustable coatings prepared via plasma spray process,” Appl. Surf. Sci., 478, 478 – 486 (2019).
J. Joseph, P. Hodgson, T. Jarvis, et al., “Effect of hot isostatic pressing on the microstructure and mechanical properties of additive manufactured AlxCoCrFeNi high entropy alloys,” Mater. Sci. Eng. A, 733, 59 – 70 (2018).
R. Jian, L.Wang, S. Zhou, et al., “Achieving fine-grain tungsten heavy alloys by selecting a high entropy alloy matrix with low Wgrain growth rate,” Mater. Lett., 278, 128405 (2020).
V. E. Gromov, S. V. Konovalov, Yu. F. Ivanov, and K. A. Osintsev, “Structure and properties of high-entropy alloys,” Adv. Struct. Mater., 107, 110 (2021).
A. A. Rempel and B. R. Gelchinsky, “High-entropy alloys: obtaining, properties, practical application,” Chern. Metall., 63(3–4), 248 – 253 (2020).
A. S. Rogachev, “Structure, stability, and properties of high-entropy alloys,” Fiz. Met. Metalloved., 121, 807 – 841 (2020).
V. F. Bashev and A. I. Kushnerev, “Structure and properties of cast and liquid-quenched high-entropy alloys of the Al – Cu – Fe – Ni – Si system,” Fiz. Met. Metalloved., 118(1), 42 – 50 (2017).
D. G. Shaisultanov, N. D. Stepanov, G. A. Salishchev, and M. A. Tikhonovskii, “Effect of heat treatment on the structure and hardness of high-entropy alloys CoCrFeNiMnVX (X = 0.25, 0.5, 0.75, 1),” Fiz. Met. Metalloved., 118(6), 610 – 621 (2017).
T. Zhang, L. Xin, F. Wu, et al., “Microstructure and mechanical of FexCoCrNiMn high-entropy alloys,” J. Mater. Sci. Technol., 35(10), 2331 – 2335 (2019).
B. A. Gludovatz, A. Hohenwarter, and D. Catoor, et al., “Fracture- resistant high-entropy alloy for cryogenic applications,” Science, 345(6201), 1153 – 1158 (2014).
D. I. Proskyrovsky, V. P. Rotshtein, G. E. Ozur, et al., “Physical foundations for surface treatment of materials with low energy, high current electron beams,” Surf. Coat. Technol., 125(1–3), 49 – 56 (2000).
S. Konovalov, Y. Ivanov, V. Gromov, and I. Panchenko, “Fatigue- induced evolution of AISI 310S steel microstructure after electron beam treatment,” Materials, 13(20), 4567 (2020).
K. Osintsev, V. Gromov, Y. Ivanov, et al., “Evolution of structure in AlCoCrFeNi high-entropy alloy irradiated by a pulsed electron beam,” Metals, 11, 1228 (2021).
GOST 1497–84. Metals. Tensile Test Methods [in Russian], Moscow, Standartinform (2005).
N. N. Koval and Yu. F. Ivanov, “Nanostructuring of the surface of metal-ceramic and ceramic materials during pulsed electron-beam processing,” Izv. Vysh. Uchebn. Zaved., Fizika, No. 5, 60 – 70 (2008).
This work was supported by the Russian Foundation for Basic Research (project No. 20-19-00452).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 5, pp. 35 – 39, May, 2022.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Gromov, V.E., Shlyarova, Y.A., Ivanov, Y.F. et al. Effect of Electron Beam Treatment on the Fracture Behavior of High–Entropy Cr – Mn – Fe – Co - Ni Alloy. Met Sci Heat Treat 64, 276–280 (2022). https://doi.org/10.1007/s11041-022-00800-2
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11041-022-00800-2