The possibility of forming coatings with a high content of amorphous phase by knock (detonation) spraying of a powder of alloy Fe66Cr10Nb5B19 of fraction 45 – 75 μm is considered. Results of comparative tests of the coatings and of a stainless steel check test piece for abrasive wear under friction against nonrigidly fixed abrasive particles conducted according to ASTM G65D are presented. The wear mechanisms of the knock-sprayed coatings with partially crystallized structure are studied.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Notes
The authors are grateful to N. Yu. Cherkasova (NSTU) for studying the morphology of the friction surfaces by scanning electron microscopy and to U. E. Bulanova for studying the size distribution of particles.
References
C. Suryanarayana and A. Inoue, “Iron-based bulk metallic glasses,” Int. Mater. Rev., 58(3), 131 – 166 (2013).
H. R. Ma, J. W. Li, J. Jiao, et al., “Wear resistance of Fe-based amorphous coatings prepared by AC-HVAF and HVOF,” Mater. Sci. Technol., 33(1), 65 – 71 (2017).
J. E. Berger, R. Schulz, S. Savoie, et al., “Wear and corrosion properties of HVOF coatings from Superduplex alloy modified with addition of boron,” Surf. Coat. Technol., 309, 911 – 919 (2017).
H. R. Ma, X. Y. Chen, J. W. Li, et al., “Fe-based amorphous coating with high corrosion and wear resistance,” Surf. Coat. Eng., 33(1), 56 – 62 (2016).
L. Xie, Y.-M. Wang, X. Xiong, et al., “Comparison of microstructure and tribological properties of plasma, high velocity oxy-fuel and detonation sprayed coatings from an iron-based powder,” Mater. Trans., 10, 1591 – 1595 (2018).
H. Wu, X. Lan, Y. Liu, et al., “Fabrication, tribological and corrosion behaviors of detonation gun sprayed Fe-based metallic glass coating,” Trans. Nonferr. Met. Soc. China, 26, 1629 – 1637 (2016).
Y. Yang, C. Zhang, Y. Peng, et al., “Effects of crystallization on the corrosion resistance of Fe-based amorphous coatings,” Corros. Sci., 59, 10 – 19 (2012).
W. Gio, Y. Wu, J. Zhang, et al., “Fabrication and characterization of thermal-sprayed Fe-based amorphous/nanocrystalline composite coatings: An overview,” J. Thermal Spray Technol., 23(7), 1157 – 1180 (2014).
V. Ulianitsky, A. Shtertser, S. Zlobin, et al., “Computer-controlled detonation spraying: From process fundamentals toward advanced applications,” J. Thermal Spray Technol., 20, 791 – 801 (2011).
V. Yu. Ul’yanitskii, “CCDS2000 — new-generation equipment for detonation spraying,” Uproch. Tekhnol. Pokr., 10, 36 – 41 (2013).
I. S. Batraev, E. S. Prokhorov, and V. Yu. Ul’yanitskii, “Acceleration and heating of powder particle by gas detonation products in channels with a conical passage,” Combus., Explos., Shock Waves, 50, 315 – 322 (2014).
I. D. Kuchumova, I. S. Batraev, N. Y. Cherkasova, et al., “The influence of the O2/C2H2 ratio on the structure and properties of Fe66Cr10Nb5B19 detonation coatings,” Mater. Today, Proc., 25, 384 – 386 (2020).
I. D. Kuchumova, I. S. Batraev, V. Yu. Ulianitsky, et al., “Formation of metallic glass coatings by detonation spraying of a Fe66Cr10Nb5B19 powder,” Metals, 9(8) (2019), mode of access: https://www.mdpi.com/2075-4701/9/8/846.
I. D. Kuchumova, I. S. Batraev, N. Yu. Cherkasova, et al., “Corrosion resistance of Fe66Cr10Nb5B19 detonation coatings under salt spray conditions,” Obrab. Met. (Tekhnol., Oborud., Instr.), 22(3), 95 – 105 (2020).
T. P. Gavrilenko, Yu. A. Nikolaev, V. Yu. Ulianitsky, et al., “Computational code for detonation spraying process,” in: Proc. Int. Thermal Spray Conf., France (1998), pp. 1475 – 1483.
T. P. Gavrilenko and Yu. A. Nikolaev, “Calculation of detonation gas spraying,” Combus., Explos., Shock Waves, 43, 724 – 731 (2007).
V. Y. Ulianitsky, I. S. Batraev, D. V. Dudina, et al., “Enhancing the properties of WC/Co detonation coatings using two-component fuels,” Surf. Coat. Technol., 318, 244 – 249 (2017).
A. Inoue, “High strength bulk amorphous alloys with low critical cooling rates,” Mater. Trans., 36(7), 866 – 875 (1995).
H. X. Li, Z. C. Lu, S. L. Wang, et al., “Fe-based bulk metallic glasses: Glass formation, fabrication, properties and applications,” Progr. Mater. Sci., 103, 235 – 318 (2019).
B. Fu, D. He, and L. Zhao, “Effect of heat treatment on the microstructure and mechanical properties of Fe-based amorphous coatings,” J. Alloys Compd., 480(2), 422 – 427 (2009).
A. A. Shtertser, V. Yu. Ul’yanitskii, and B. E. Grinberg, “Wear resistance of metallic, hard-alloy and alumina coatings obtained by detonation spraying,” Uproch. Tekhnol. Pokr., No. 3, 39 – 43 (2013).
The work has been performed with financial support of the Russian Foundation for Basic Research within scientific project No. 20-38-90069 and scientific project No. C21-13 within implementation of the program for development of the NSTU.
The study was partially conducted at the Common Access Center “Structure, Mechanical and Physical Properties of Materials” of the NSTU.
Author information
Authors and Affiliations
Additional information
Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 9, pp. 3 – 8, September, 2021.
Rights and permissions
About this article
Cite this article
Kuchumova, I.D., Bataev, V.A., Grinberg, B.E. et al. Wear Resistance of Detonation Coatings with Amorphous Structure Under Conditions of Friction Against Nonrigidly Fixed Abrasive Particles. Met Sci Heat Treat 63, 463–469 (2022). https://doi.org/10.1007/s11041-022-00714-z
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11041-022-00714-z