The influence of errors of form (ovalities) of the base surfaces of a composite axisymmetric body on the size of an adjacent contour was studied. It was proved that ovalities of all bourrelets of a composite axisymmetric body do not render an effect on the accuracy of measurement of the size of entry of this case, although they do affect the entrysize. Errors of the placement of joined tubes of the composite axisymmetric body in the form of displacements or misalignments of axes cause measurement errors of the entry size of the casings that are proportional to the ratio of the distances from the basic prisms to the end faces of tubes vs. the length of the tubes.
Similar content being viewed by others
References
M. Liennard, O. Chevalier, A. Langlet, et al., “An analysis of the accelerations of a projectile in a gun tube by direct measurements and telemetry of the data,” Mech. Ind., 19, No. 4, Art. 406 (2018).
P. Bauer, M. Hennerand, and M. Giraud, “Numerical investigation of the fin geometry of ram accelerator projectiles in subdetonative propulsion mode,” Eur. Phys. J. AP, 23, No. 2, 139–145 (2003).
T. Bengherbia, Y. R. Yao, P. Bauer, and C. Knowlen, “Numerical study of gaseous reactive flow over a ram accelerator projectile in subdetonative velocity regime,” EPJ Appl. Phys., 55, No. 1, July (2011).
M. T. Soifer and R. S. Becker, Projectile Motion in a Flexible Gun Tube, US Army Ballistic Res. Lab., Aberdeen (1984).
A. S. Yamnikov, O. A. Yamnikova, I. A. Matveev, and E. N. Rodionova, “A method of direct monitoring of the suitability of an assembled extended cylindrical projectile body,” Izmer. Tekhn., No. 9, 31–35 (2018), DOI: https://doi.org/10.32446/0368-1025it.2018-9-31-35.
A. I. Orlov, The Mathematics of Chance. Probability and Statistics – Basic Facts: Textbook, MZ-Press, Moscow (2004).
E. S. Venttsel, Probability Theory: Textbook, Yustitsiya, Moscow (2018), 12th ed.
A. S. Vasilev, A. S. Yamnikov, O. A. Yamnikova, and I. A. Matveev, “The influence of inherent technological deviations of manufacturing of the base tube on the parameters of a composite propulsion engine,” Chern. Met., No. 1, 67–72 (2019).
I. A. Matveev and A. S. Yamnikov, “Precision of long thin-walled axisymmetric parts in cutting and pressure treatment,” Russ. Eng. Res., 38, No. 9, 719–720 (2018).
A. I. Geilikman and E. I. Matov, “Calculation of mutual alignment errors of two components connected on thread and smooth surfaces,” in: Engineering Technology, TPI, Tula (1972), pp. 42–57.
A. A. Red’ko, S. A. Poltorykhin, S. A. Kudryavtsev, and I. L. Kosarev, “The influence of technological deviations in the manufacture of PC MLRS on their dispersion during firing,” Boeprip. Vysokoenerg. Kondens. Sist., No. 1, 32–35 (2008).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Izmeritel’naya Tekhnika, No. 8, pp. 29–32, August, 2019.
Rights and permissions
About this article
Cite this article
Yamnikov, A.S., Rodionova, E.N., Yamnikova, O.A. et al. The Effect of Errors of the Form and Position of the Base Surfaces of a Composite Axisymmetric Body on the Size of an Adjacent Contour. Meas Tech 62, 692–696 (2019). https://doi.org/10.1007/s11018-019-01680-4
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11018-019-01680-4