Skip to main content
SpringerLink
Log in

Development of a Model Series of Hardware-Software Complexes for Automated Measurements of the Parameters of Gear-Cutting Tools

  • Published:
Measurement Techniques Aims and scope

Results from a study of the design of a model series of hardware-software complexes for automated measurements of the parameters of gear-cutting tools are presented. The technical characteristics, structural designs, and features of the software are presented.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1

Similar content being viewed by others

References

  1. S. N. Grigoriev et al., “Contemporary state and outlook for the development of metrological assurance in the machinebuilding industry,” Izmer. Tekhn., No. 11, 56–59 (2012); Measur. Techn., 55, No. 11, 1311–1315 (2012).

  2. S. N. Grigoriev et al., “The problems of metrological support for the preparation of production in machine construction,” Izmer. Tekhn., No. 5, 27–29 (2012); Measur. Techn., 55, No. 11, 526–529 (2012).

  3. Y. A. Maksin, V. I. Teleshevskii, and P. V. Temnikov, “System for computer aided design and fabrication of means of linear-angular measurement based on three-dimensional parametric modeling,” Izmer. Tekhn., No. 8, 13–16 (2011); Measur. Techn., 54, No. 8, 869–873 (2011).

  4. S. E. Ped’ and E. V. Darienko, “Error estimates in coordinate measurements of the cross section parameters of cylindrical surfaces,” Izmer. Tekhn., No. 8, 17–19 (2011); Measur. Techn., 54, No. 8, 874–879 (2011).

  5. V. I. Teleshevskii, A. V. Shulepov, and E. M. Rozdina, “Smart computer microscopy for measurement of linear and angular dimensions of work pieces,” Izmer. Tekhn., No. 8, 3–6 (2011); Measur. Techn., 54, No. 8, 853–858 (2011).

  6. P. N. Emel’yanov, S. E. Ped’, and I. E. Kholin, “Development of programmed numerically controlled reference plate-measuring engine,” Inform.-Izmer. Upravl. Sistemy, 10, No. 8, 68–73 (2012).

  7. S. G. Konov, “Development of contact-type plate-measuring engine based on a photogrammatic system,” Vest. MGTU Stankin, No. 2, 119–121 (2010).

  8. GOST 17336–80, Devices for Measurement of Hobbing Cutters. Types and Basic Parameters. General Technical Requirements.

  9. GOST 13755–81, Basic Standards of Interchangeability. Involute Gearing. Initial Contour.

Download references

Author information

Authors and Affiliations

  1. State Engineering Center, STANKIN Moscow State Technological University, Moscow, Russia

    S. E. Ped’ & D. A. Masterenko

  2. Research and Design Institute of Measuring Means in Mechanical Engineering (NIIizmereniya), Moscow, Russia

    P. V. Panfilov & A. V. Es’kov

  3. ChelyabNIIKontrol Company, Chelyabinsk, Russia

    I. V. Surkov

Authors
  1. S. E. Ped’
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. D. A. Masterenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. P. V. Panfilov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. V. Es’kov
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. I. V. Surkov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. E. Ped’.

Additional information

Translated from Izmeritel’naya Tekhnika, No. 12, pp. 27–31, December, 2013.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Ped’, S.E., Masterenko, D.A., Panfilov, P.V. et al. Development of a Model Series of Hardware-Software Complexes for Automated Measurements of the Parameters of Gear-Cutting Tools. Meas Tech 56, 1370–1376 (2014). https://doi.org/10.1007/s11018-014-0384-5

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11018-014-0384-5

Keywords

Search

Navigation