This article reveals the relevance of the development of production of clad plates and large-diameter pipes in Russia. The most widespread technologies in the world are compared. The results of the mathematical and physical modeling of the rolling of bimetallic packs into strips are described. The use of pack rolled clad plates is shown to be preferable for the production of large-diameter electric-welded pipes. The main production aspects of clad plates from a pack billet on a plate mill and their resulting pipes are presented.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
I. G. Rodionova, A. A. Pavlov, and A. I. Zaitsev, Corrosion-Resistant Bimetals with Strong Adhesion of Layers for the Petrochemical Industry and Other Industries [in Russian], Metallurgizdat, Moscow (2011).
O. L. Pervukhina et al., “Steel-titanium bimetal for nuclear engineering, scientific and technical progress in ferrous metallurgy (proceedings),” Mater. II Intern. Sci.-Tech. Conf. (2015).
A. A. Berdychenko and L. B. Pervukhin, “Difficulties in explosion welding of large-sized bimetal plates with a titanium cladding layer and ways to overcome them,” Polzunovskiy Al’manakh, No. 3, 25–27 (2008).
V. G. Pinaev and V. M. Andrianov, “Possibilities of using bimetals obtained by explosion welding,” Sudostroyeniye, No. 12, 26–28 (2009).
V. I. Lysak and S. V. Kuzmin, “Experience in the manufacture of large-sized bimetallic plates with a corrosion-resistant layer by explosion welding,” Izvestiya VolGTU, 4–15.
A. I. Zaitsev et al., “Influence of composition, structural state, production technology on service properties of high-strength lowcarbon steel of the bimetal main layer,” Metallurg, No. 8, 50–58 (2015).
Shunichi Tachibana, Yota Kuronuma, Tomoyuki Yokota, Shinji Mitao and Hitoshi Sueyoshi, Yutaka Wada and Keizou Yabumoto, Moriya Yutaka, and Nagae Moriyasu, “Development of TMCP type alloy 625/X65 clad steel plate for pipe,” Proceedings of the 2014 10th Intern. Pipeline Conf. IPC 2014, September 29 – October 3, 2014, Calgary, Alberta, Canada (2014).
M. Tsuji, Y. Kobayashi, M. Suga, K. Urne, H. Torna, and M. Itoh, “High Ni alloy (type 825) clad pipe manufactured by UOE process,” Copyright 1989, Offshore Technology Conference, this paper was presented at the 21st Annual OTC in Houston, Texas, May 1–4 (1989).
U. Malina-Altzinger, H. Ornig, and R. Schimbock, “Hot rolled clad plates for application in flue gas desulfurization (FGD)-systems,” J. Werkstoffe Korrovon, 43, 280–283 (1992).
F. Winter, K. Schindler, F. J. Wahlers, et al., Patent No. 2711690 C1 RF, IPC C21D 8/02, A Method of Manufacturing a Roll-Clad Metal Plate, applicant Westalpin Grobblech GMBH, VDM Metals International GMBH. No. 2019102844, decl. 08/10/2017, publ.01/21/2020.
S. V. Mishustin, K. I. Schukin, A. V. Muntin, et al., Patent No. 2714150 C1 RF, IPC C21D 8/04, B23K 20/04, C21D 9/48, A Method of Manufacturing Steel Two-Layer Hot-Rolled Plates, applicant Vyksa Steel Works, No. 2019127803, submitted Septebmer 9, 2019, published February 12, 2020.
S. A. Golovanenko, Bimetal Rolling Welding [in Russian], Metallurgiya, Moscow (1977).
N. V. Selivonchik and Yu. L. Bobarikin, “Analysis of the conditions for achieving adhesion between bimetal layers during rolling cladding,” Vestnik GGTU im. P. O. Sukhogo, No. 1, 29–38 (2009).
E. A. Goli-Oglu, A. N. Alistaev, V. I. Ilyinsky, et al., “Peculiarities of formation of microstructure and mechanical properties of low-alloyed steel using various schemes of thermomechanical treatment,” Chern. Metally, No. 12(984), 19–26 (2013).
V. A. Durynin et al., Patent 2274528 RF, A Method for Manufacturing Packages for the Production of Large-Sized Clad Plates, applicant and patent holder OMZ-Spetsstal, No. 204114068/02, submitted March 6, 2004; published April 20, 2006, Bull. No. 11.
E. S. Kagan et al., Patent 2277464 RF, The Method of Evacuation of Multilayer Packages for Rolling and a Device for Its Implementation, applicant and patent holder OMZ-Spetsstal, No. 204125122/02, submitted August, 2004; June 10, 2006, Bull. No. 16.
S. A. Barannikova et al., “Investigation of the inhomogeneity of plastic strain in a bimetal,” Vestn. Tambovsk. Univ. Ser.: Yestestv, Tekhnich. Nauki, No. 3, 877–881 (2016).
V. F. Potapkin, A. V. Satonin, and A. A. Satonin, “Mathematical modeling of the metal stress-strain state during the implementation of the processes of cladding and rolling of multilayer polymetallic plates and strips,” Izvestiya TulGU, TulGU, Tula, 1, 77–85 (2004).
A. G. Zinyagin, A. V. Muntin, V. I. Ilyinsky, and G. S. Nikitin, “Mathematical modeling of the process of accelerated cooling of the plate on the mill 5000,” Problemy Chern. Metallurg Materialoved., No. 1, 9–15 (2013).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Metallurg, Vol. 66, No. 9, pp. 23–30, September, 2022. Russian DOI:https://doi.org/10.52351/00260827_2022_09_23
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Dunaev, V.V., Muntin, A.V., Samokhvalov, M.V. et al. Aspects of the Production Technology of Largesized Clad Plates and Large Diameter Pipes Made From Them. Metallurgist 66, 1040–1050 (2023). https://doi.org/10.1007/s11015-023-01417-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11015-023-01417-3