Skip to main content
SpringerLink
Log in

Elevation of the Wear Resistance of Roller Dies for the Production of Wires from Titanium Alloys

  • Published:
Metallurgist Aims and scope

We propose a technology of hardening of the working surfaces of the rollers of dies intended for the treatment of titanium alloys. The detonation deposition of the WC–10Co–4Cr alloy with a thickness of 600 μm and subsequent fusion of this layer with the help of a laser make it possible to increase the hardness of the working layer up to 1057 HV (> 67 HRC). In this case, the wear resistance becomes more than seven times higher as compared with the case of traditional thermal treatment applied for Kh12MFsteel.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.

Similar content being viewed by others

References

  1. B. B. Chechulin, S. S. Ushkov, and I. N. Razuvaev, Titanium Alloys in Mechanical Engineering [in Russian], Mashinostroenie, Leningrad (1977).

    Google Scholar 

  2. A. V. Kop’ev, Resource-Saving Technological Processes of Rolling of Wires in a Continuous Mill with Four-Roll Passes [in Russian], Candidate-Degree Thesis (Engineering) Magnitogorsk (2001).

  3. G. S. Khayak, Drawing of Wire from Nonferrous Metals and Alloys [in Russian], Metallurgiya, Moscow (1967).

    Google Scholar 

  4. A. S. Anishchenko, “Drawing of titanium wires under isothermal conditions,” Vopr. Materialoved., Issue 2, 45–53 (1995).

  5. V. I. Lepekhov, A. S. Anishchenko, and G. S. Lupandin, “Improvement of the technology of isothermal drawing of titanium wires,” Visn. Pryazov. Derzh. Tekh. Univ.: Zbir. Nauk. Prats,’ Issue 2, 74–76 (1996).

  6. A. A. Shter, Yu. N. Popov, and B. V. Barichko, “Production of wires and shapes from titanium-based alloys in roller dies,” in: Treatment of Solid and Layered Materials: Interuniversity Collection of Scientific Works [in Russian], Magnitogorsk State Technical University, Magnitogorsk (1999), pp. 88–92.

  7. A. P. Grudev, Yu. V. Zil’berg , and V. T. Tilik, Friction and Lubricants in Plastic Metal Working [in Russian], Metallurgiya, Moscow (1982).

    Google Scholar 

  8. A. V. Vydrin, B. V. Barichko, and V. S. Barichko, “Development of the rational conditions of deformation of metals in roller dies with the use of the methods of modeling in: Proc. of the 6th Congr. of Rolling Experts [in Russian], “Chermetinformatsiya” LLC, Moscow (2005), pp. 475–480.

  9. L. V. Radionova and A. A. Radionov, “Current state and prospects of the development of drawing production of steel wires,” Mashinostroen.: Setev. Élektr. Nauch. Zh., No. 1, 3–11 (2013).

  10. V. S. Slavin, Roller Dies of the Housingless Type: A Monograph [in Russian], Magnitogorsk State University, Magnitogorsk (2010).

    Google Scholar 

  11. S. I. Yares’ko, “Improvement the operating characteristics of hard-alloy tools by laser treatment,” Fiz. Khim. Obrab. Mater., No. 5, 18–22 (2003).

    Google Scholar 

  12. I. N. Stepankin, E. P. Pozdnyakov, and E. A. Astapov, “On the problem of structure formation and hardness of Kh12M semi-heatresistant steel by the methods of thermal and chemicothermal treatment,” Vest. Polotsk. Gos. Univ., Ser. B, No. 3, 107–114 (2016).

  13. M. A. Filippov, M. A. Gervas’ev, G. N. Plotnikov, A. S. Zhilin, and S. M. Nikiforova, “Formation of structure of wear-resistant steels 150KhNML and Kh12MFL upon hardening,” Metalloved. Term. Obrab. Met., 11, 5–9 (2015); English translation: Met. Sci. Heat Treat., 57, Issues 11–12, 641–644 (2016); DOI: https://doi.org/10.1007/s11041-016-9935-5.

  14. А. Е. Sarafanov, L. V. Radionova, I. N. Erdakov, and M. A. Zhludov, “Design, principle of operation of a unit, and the procedure of testing for abrasive wear-resistance,” Mashinostroen.: Setev. Élektr. Nauch. Zh., 8, No. 2, 8–11 (2020); DOI: https://doi.org/10.24892/RIJIE/20200202.

    Article  Google Scholar 

  15. M. Samodurova, L. Radionova, and R. Zakirov, “A study of the structural characteristics of titanium alloy products manufactured using additive technologies by combining the selective laser melting and direct metal deposition methods,” Materials, 12, No. 19 (2019); DOI: https://doi.org/10.3390/ma12193269.

  16. M. Samodurova, L. Radionova, and R. Zakirov, “A study of characteristics of aluminum bonze coatings applied to steel using additive technologies,” Materials, 13, No. 461 (2020); DOI: https://doi.org/10.3390/ma13020461.

  17. CASTOLIN EUTECTIC [Electronic Resource]: Official Internet Site. URL: https://www.castolin.com/ (Date of access 09.04.2020).

  18. V. A. Bykov, L. V. Radionova, and M. N. Samodurova, “Reconstruction of a plunger pair by detonation spraying of a functional coating,” in: Proc. of the 6th Internat. Sci.-Pract. Conf. of Young Scientists and Students [in Russian], Donetsk (2020), pp. 200–203.

Download references

Author information

Authors and Affiliations

  1. South Ural State University, Chelyabinsk, Russia

    L. V. Radionova, M. N. Samodurova, A. E. Sarafanov, V. A. Bykov, L. A. Glebov & K. Yu. Pashkeev

Authors
  1. L. V. Radionova
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. N. Samodurova
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. E. Sarafanov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. V. A. Bykov
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. L. A. Glebov
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. K. Yu. Pashkeev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to L. V. Radionova.

Additional information

Translated from Metallurg, Vol. 64, No. 11, pp. 75–81, November, 2020.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Radionova, L.V., Samodurova, M.N., Sarafanov, A.E. et al. Elevation of the Wear Resistance of Roller Dies for the Production of Wires from Titanium Alloys. Metallurgist 64, 1188–1197 (2021). https://doi.org/10.1007/s11015-021-01104-1

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11015-021-01104-1

Keywords

Search

Navigation