Skip to main content
SpringerLink
Log in

Alternative Technology for Manufacturing Rod–Wire Products from AK12 Silumin

  • Published:
Metallurgist Aims and scope

We develop and test a flow diagram of the process of manufacturing of rods and wires from graded loose chip wastes of eutectic silumin based on the use solely of the procedures of plastic working and heat treatment. In its realization, we use the method of combined rolling–pressing of preliminarily briquetted chips with subsequent drawing of pressed rods. The possibility of getting semifinished and finished products with higher levels of strength and plastic properties as compared with cast silumin is demonstrated. The specific features of formation of the structure of the material after the realization of individual stages of the general flow diagram are indicated.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.
Fig. 7.
Fig. 8.

Similar content being viewed by others

References

  1. S. G. Alieva, M. B. Al’tman, S. M. Ambartsumyan, et al., Commercial Aluminum Alloys: A Handbook [in Russian], Metallurgiya, Moscow (1984).

  2. N. A. Belov, Phase Compositions of Commercial and Promising Aluminum Alloys [in Russian], Moscow Institute of Steel and Alloys, Moscow (2010).

    Google Scholar 

  3. S. M. Aktarer, D. M. Sekban, O. Saray, et al., “Effect of two-pass friction stir processing on the microstructure and mechanical properties of as-cast binary Al–12Si alloy,” Mater. Sci. Eng. A, 636, 311–319 (2015).

    Article  CAS  Google Scholar 

  4. O. El Sebaie, A. M. Samuel, F. H. Samuel, and H. W. Doty, “The effects of mischmetal, cooling rate, and heat treatment on the hardness of A319.1, A356.2 and A413.1 Al–Si casting alloys,” Mater. Sci. Eng. A, 486, Issues 1–2, 241–252 (2008).

    Article  Google Scholar 

  5. A. Dolata-Grosz, J. Śleziona, and B. Formanek, “Structure and properties of aluminum cast composites strengthened by dispersion phases,” J. Mater. Process. Technol., 175, Issue 1–3, 192–197 (2006).

    Article  CAS  Google Scholar 

  6. V. G. Trifonov, I. V. Kamalova, V. S. Romanova, and V. N. Platonov, “Hot deformation regimes, their influence on structure and mechanical properties of silumin-based composite materials, and specific features of this influence,” Mater. Sci. Eng. A, 234–236, 242–244 (1997).

    Article  Google Scholar 

  7. D. Yu. Gorbunov, G. V. Rovenskii, and T. V. Stainova, “Investigation of the deformation parameters of modified aluminum–silicon alloys and the mechanical properties of thin-walled cold-deformed semifinished products made of these alloys,” Tekhnol. Legk. Splavov, No. 6, 29–32 (2004).

  8. V. D. Solovei and Yu. N. Loginov “Calculating extrusion textures of the alloy Mn–Al–C,” Textures Microstruct., 28, 121–128 (1996).

    Article  CAS  Google Scholar 

  9. S. B. Sidel’nikov, N. N. Dovzhenko, and N. N. Zagirov, Combined and Mixed Treatment Methods for Nonferrous Metals and Alloys [in Russian], MAKS Press, Moscow (2005).

    Google Scholar 

  10. A. A. Ershov, Yu. N. Loginov, N. N. Zagirov, and E. V. Ivanov, “Simulation of the consolidation of a porous material in combined rolling–extrusion process,” Metallurg, No. 6, 14–17 (2017); English translation: Metallurgist, 60, Nos. 5-6, 561–565 (2016).

  11. P. K. Saha, Aluminum Extrusion Technology, ASM International (2000).

  12. S. N. Ab Rahim, M. A. Lajis, and S. Ariffin, “A review on recycling aluminum chips by hot extrusion process,” Proc. CIRP, Vol. 26, 761–766 (2015).

    Article  Google Scholar 

  13. H. E. Hu, X.-Y. Wang, and L. Deng, “High temperature deformation behavior and optimal hot processing parameters of Al–Si eutectic alloy,” Mater. Sci. Eng. A, 576, 45–51 (2013).

    Article  CAS  Google Scholar 

  14. E. M. Herba and H. J. McQueen, “Influence of particulate reinforcements on 6061 materials in extrusion modeling,” Mater. Sci. Eng. A, 372, 1–14 (2004).

    Article  Google Scholar 

  15. Yu. M. Vainblat, P. Sh. Lantsman, and N. A. Sharshagin, “Diagrams of the structural states of hot-deformed aluminum alloys,” Izv. Vyssh. Uchebn. Zaved., Tsvet. Metallurg., No. 4, 155–161 (1974).

  16. V. Güley, A. Güzel, A. Jäger, et al., “Effect of die design on the welding quality during solid state recycling of AA6060 chips by hot extrusion,” Mater. Sci. Eng. A, 574, 163–175 (2012).

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Federal State Autonomous Educational Institution of Higher Education “Siberian Federal University”, Krasnoyarsk, Russia

    N. N. Zagirov & E. V. Ivanov

  2. Federal State Autonomous Educational Institution of Higher Education “El’tsin Ural Federal University”, Ekaterinburg, Russia

    Yu. N. Loginov

  3. Federal State Autonomous Educational Institution of Higher Education “Siberian Federal University”, Krasnoyarsk, Russia

    S. B. Sidel’nikov

Authors
  1. N. N. Zagirov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Yu. N. Loginov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. B. Sidel’nikov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. E. V. Ivanov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to N. N. Zagirov.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zagirov, N.N., Loginov, Y.N., Sidel’nikov, S.B. et al. Alternative Technology for Manufacturing Rod–Wire Products from AK12 Silumin. Metallurgist 62, 587–596 (2018). https://doi.org/10.1007/s11015-018-0696-9

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11015-018-0696-9

Keywords

Search

Navigation