Modeling and predicting the course of events in production processes based on data in information-based control systems makes it possible to correct those processes, eliminate errors that were allowed to occur in previous conversions, and thus obtain a high-quality product.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
N. G. Tomson, “Quality management systems in Russia. Open systems,” Stand. Kach., No. 11, 10–12 (2006).
V. A. Kachalov, “The significance of ‘constantly improving the results obtained with quality control systems,’” Metody Menedzh. Kach., No. 1, 28–32 (2007).
A. A. Morozov, F. V. Kaptsan, V. N. Urtsev, et al., “Development of product-quality control systems at the MMK,” Stal, No. 5, 53–55 (2005).
A. A. Morozov, F. V. Kaptsan, V. N. Urtsev, et al., “Introduction of product-quality control systems at the Magnitogorsk Metallurgical Combine,” in: Creation and Implementation of Corporate Information Systems (CIS) at Factories in the Russian Federation: Proc. All-Russ. Sci.-Techn. Conf., IPTs Prof-Print, Magnitogorsk (2005), Vol. 1, pp. 9–11.
G. S. Senichev, I. V. Vier, V. V. Kurban, et al., “Corporate system for normative-reference tracking,” Stal, No. 5, 120–121 (2005).
A. A. Morozov, F. V. Kaptsan, V. N. Urtsev, et al., “Introduction of product-quality control systems at the Magnitogorsk Metallurgical Combine,” ibid., 9–11.
S. N. Rakhimov,V. V. Kurban, F. V. Kaptsan, and I. V. Vier, “Improving the NRI quality control system at the MMK,” ibid., 110–114.
V. V. Kurban, V. M. Salganik, and A. M. Pesin, “Use of artificial neural networks for the quality control of flat hot-rolled products on the 2000 mill at the MMK,” in: Modeling and Development of Metal-Shaping Technologies: Coll. Sci. Papers, MGTU im. G. I. Nosova, Magnitogorsk (2006), pp. 20–26.
V. N. Timoshenko and V. V. Kurban, “Devising a method of deciding on the chemical composition of microalloyed steels with prescribed mechanical properties,” in: Modeling and Development of Metal-Shaping Technologies: Inter-Regional Coll. Sci. Papers, MGTU im. G. I. Nosova, Magnitogorsk (2009), pp. 224–232.
V. M. Salganik, A. M. Pesin, V. V. Kurban, et al., “Deciding on the chemical compositions of microalloyed steels with mechanical properties conforming to API 5L,” ibid., pp. 233–239.
V. M. Timoshenko, V. M. Salganik, A. M. Pesin, et al., “Deciding on the chemical compositions and method of production of wide rolled strip made of new grades of low-alloy tube steels to obtain products with a unique combination of commercial properties,” in: Improved Metallurgical Materials and Technologies: Proc. Int. Sci.-Techn. Conf., St. Petersburg State Polytechnic Univ., St. Petersburg (2009), pp. 248–252.
Author information
Authors and Affiliations
Corresponding author
Additional information
P. P. Semenov and V. T. Fominykh also participated in this study.
Translated from Metallurg, No. 5, pp. 63–67, May, 2011.
Rights and permissions
About this article
Cite this article
Kurban, V.V., Salganik, V.M., Pesin, A.M. et al. Improving the quality control system for hot- and cold-rolled products at the Magnitogorsk Metallurgical Combine. Metallurgist 55, 364 (2011). https://doi.org/10.1007/s11015-011-9437-z
Received:
Published:
DOI: https://doi.org/10.1007/s11015-011-9437-z