Skip to main content
SpringerLink
Log in

Preparation, characterization and thermal properties of surface-modified expanded perlite/paraffin as a form-stable phase change composite in concrete

  • Published:
Journal of Thermal Analysis and Calorimetry Aims and scope Submit manuscript

Abstract

Energy storage plays an important role in improving the applicability of a wide range of energy systems. Buildings could be considered as a desirable place for this purpose. Incorporating phase change materials (PCMs) as form-stable composites into the building materials has been widely taken into consideration in recent years. However, there are still some shortcomings in applying this technique. In this study, we focused on a surface modification method to prevent leakage of PCM from porous aggregates during heating/cooling cycles. Paraffin (PA) as phase change material was impregnated into the expanded perlite (EP) particles by vacuum impregnation method, and prepared EP/PA composite was coated by a layer of polystyrene. Thermal characterization of obtained composite samples was conducted by DSC and TG analysis. Also, a simple apparatus was prepared to evaluate thermal behavior of a concrete block made by these modified form-stable PCMs during the heating process. Oozing circle method and visual observation for leakage were conducted for surface-modified EP/PA particles and final concrete blocks, respectively. Finally, compressive strength test was applied to evaluate the feasibility of using concretes made by EP/PA composites as structural concrete. The results showed that using polystyrene as a coating material for EP/PA particles was a promising method for PCM leakage prevention. Latent heat value decreased about 18% for surface-modified EP/PA but no leakage trace was observed; also in spite of decreasing in compressive strength up to 40%, it is still in acceptable range for structural purposes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Hawes DW, Feldman D, Banu D. Latent heat storage in building materials. Energy Build. 1993;20(1):77–86.

    Article  Google Scholar 

  2. Abuelnuor AA, Omara AAM, Saqr KM, Elhag IHI. Improving indoor thermal comfort by using phase change materials: a review. Int J Energy Res. 2018;42(6):2084–103.

    Article  CAS  Google Scholar 

  3. Hawes DW, Banu D, Feldman D. Latent heat storage in concrete. Sol Energy Mater. 1989;19(3–5):335–48.

    Article  CAS  Google Scholar 

  4. Memon SA. Phase change materials integrated in building walls: a state of the art review. Renew Sustain Energy Rev. 2014;31:870–906.

    Article  Google Scholar 

  5. Schossig P, Henning HM, Gschwander S, Haussmann T. Micro-encapsulated phase-change materials integrated into construction materials. Sol Energy Mater Sol Cell. 2005;89(2):297–306.

    Article  CAS  Google Scholar 

  6. Sarı A, Karaipekli A, Kaygusuz K. Capric acid and stearic acid mixture impregnated with gypsum wallboard for low-temperature latent heat thermal energy storage. Int J Energy Res. 2008;32(2):154–60.

    Article  Google Scholar 

  7. Zhang D, Zhou J, Wu K, Li Z. Granular phase changing composites for thermal energy storage. Sol Energy. 2005;78(3):471–80.

    Article  CAS  Google Scholar 

  8. Sharifi NP, Sakulich A. Application of phase change materials to improve the thermal performance of cementitious material. Energy Build. 2015;103:83–95.

    Article  Google Scholar 

  9. Lu Z, Zhang J, Sun G, Xu B, Li Z, Gong C. Effects of the form-stable expanded perlite/paraffin composite on cement manufactured by extrusion technique. Energy. 2015;82:43–53.

    Article  CAS  Google Scholar 

  10. Ramakrishnan S, Sanjayan J, Wang X, Alam M, Wilson J. A novel paraffin/expanded perlite composite phase change material for prevention of PCM leakage in cementitious composites. Appl Energy. 2015;157:85–94.

    Article  CAS  Google Scholar 

  11. Li X, Sanjayan JG, Wilson JL. Fabrication and stability of form-stable diatomite/paraffin phase change material composites. Energy Build. 2014;76:284–94.

    Article  Google Scholar 

  12. Zhang J, Guan X, Song X, Hou H, Yang Z, Zhu J. Preparation and properties of gypsum based energy storage materials with capric acid–palmitic acid/expanded perlite composite PCM. Energy Build. 2015;92:155–60.

    Article  Google Scholar 

  13. Zhang N, Yuan Y, Yuan Y, Li T, Cao X. Lauric–palmitic–stearic acid/expanded perlite composite as form-stable phase change material: preparation and thermal properties. Energy Build. 2014;82:505–11.

    Article  Google Scholar 

  14. Liu P, Gu X, Bian L, Peng L, He H. Capric acid/intercalated diatomite as form-stable composite phase change material for thermal energy storage. J Therm Anal Calorim. 2019;138(1):359–68.

    Article  CAS  Google Scholar 

  15. Sarı A, Biçer A. Preparation and thermal energy storage properties of building material-based composites as novel form-stable PCMs. Energy Build. 2012;51:73–83.

    Article  Google Scholar 

  16. Biçer A, Sarı A. New kinds of energy-storing building composite PCMs for thermal energy storage. Energy Convers Manag. 2013;69:148–56.

    Article  Google Scholar 

  17. Kenisarin MM, Kenisarina KM. Form-stable phase change materials for thermal energy storage. Renew Sustain Energy Rev. 2012;16(4):1999–2040.

    Article  CAS  Google Scholar 

  18. Ramakrishnan S, Wang X, Sanjayan J, Wilson J. Assessing the feasibility of integrating form-stable phase change material composites with cementitious composites and prevention of PCM leakage. Mater Lett. 2017;192:88–91.

    Article  CAS  Google Scholar 

  19. Cheng F, Wen R, Zhang X, Huang Z, Huang Y, Fang M, et al. Synthesis and characterization of beeswax-tetradecanol-carbon fiber/expanded perlite form-stable composite phase change material for solar energy storage. Compos Part A. 2018;107:180–8.

    Article  CAS  Google Scholar 

  20. Kong X, Zhong Y, Rong X, Min C, Qi C. Building energy storage panel based on paraffin/expanded perlite: preparation and thermal performance study. Materials. 2016;9(2):70.

    Article  Google Scholar 

  21. Li X, Chen H, Liu L, Lu Z, Sanjayan JG, Duan WH. Development of granular expanded perlite/paraffin phase change material composites and prevention of leakage. Sol Energy. 2016;137:179–88.

    Article  CAS  Google Scholar 

  22. Kheradmand M, Castro-Gomes J, Azenha M, Silva PD, de Aguiar JLB, Zoorob SE. Assessing the feasibility of impregnating phase change materials in lightweight aggregate for development of thermal energy storage systems. Constr Build Mater. 2015;89:48–59.

    Article  Google Scholar 

  23. Kolthoff IM, O’connor PR, Hansen JL. Mechanism of emulsion polymerization of styrene with persulfate as activator in the absence and presence of mercaptan and a retarder. J Polym Sci. 1955;15(80):459–73.

    Article  CAS  Google Scholar 

  24. Ma B, Adhikari S, Chang Y, Ren J, Liu J, You Z. Preparation of composite shape-stabilized phase change materials for highway pavements. Constr Build Mater. 2013;42:114–21.

    Article  CAS  Google Scholar 

  25. Kong X, Yao C, Jie P, Liu Y, Qi C, Rong X. Development and thermal performance of an expanded perlite-based phase change material wallboard for passive cooling in building. Energy Build. 2017;152:547–57.

    Article  Google Scholar 

  26. Mehta S, Biederman S, Shivkumar S. Thermal degradation of foamed polystyrene. J Mater Sci. 1995;30(11):2944–9.

    Article  CAS  Google Scholar 

  27. Lorwanishpaisarn N, Kasemsiri P, Posi P, Chindaprasirt P. Characterization of paraffin/ultrasonic-treated diatomite for use as phase change material in thermal energy storage of buildings. J Therm Anal Calorim. 2016;128(3):1293–303.

    Article  Google Scholar 

  28. Hasanabadi S, Sadrameli SM, Soheili H, Moharrami H, Heyhat MM. A cost-effective form-stable PCM composite with modified paraffin and expanded perlite for thermal energy storage in concrete. J Therm Anal Calorim. 2018;136:1201–16.

    Article  Google Scholar 

Download references

Acknowledgements

Financial support from the Research Department of Tarbiat Modares University and Iranian Science Foundation (INSF) is gratefully acknowledged by the first and second authors.

Author information

Authors and Affiliations

  1. Process Engineering Department, Faculty of Chemical Engineering, Tarbiat Modares University, Tehran, Iran

    Salman Hasanabadi & Seyed Mojtaba Sadrameli

  2. Department of Chemical Engineering, Isfahan University of Technology, Isfahan, Iran

    Samaneh Sami

Authors
  1. Salman Hasanabadi
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Seyed Mojtaba Sadrameli
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Samaneh Sami
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Salman Hasanabadi.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Hasanabadi, S., Sadrameli, S.M. & Sami, S. Preparation, characterization and thermal properties of surface-modified expanded perlite/paraffin as a form-stable phase change composite in concrete. J Therm Anal Calorim 144, 61–69 (2021). https://doi.org/10.1007/s10973-020-09440-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10973-020-09440-1

Keywords

Search

Navigation