Skip to main content

Epoxy-matrix composites filled with surface-modified SiO2 nanoparticles

Journal of Thermal Analysis and Calorimetry volume 127, pages 399–408 (2017)Cite this article

Abstract

Composites based on an epoxy resin, diglycidyl ether of bisphenol A and SiO2 nanoparticles, unmodified and surface-modified with a coupling agent 3-glycidyloxypropyltrimethoxysilane, were prepared. Successful modification of the nanoparticles was confirmed by infrared spectroscopy and combined differential scanning calorimetry and thermogravimetric analysis (DSC–TG). Composite materials were prepared by adding 0.5–5 phr (parts per hundred parts of resin) of modified and unmodified nanoparticles into the epoxy resin which was then cured with a poly(oxypropylene) diamine. Curing was followed by DSC, and cured materials were characterised by tensile and hardness testing. Morphology of fractured surfaces after tensile testing was investigated by scanning electron microscopy (SEM). Thermal stability of cured materials was studied by TG and their glass transition temperature determined by DSC. The presence of the filler was found not to influence the curing mechanism of the epoxy resin nor the degradation mechanism of the crosslinked epoxy–amine matrix. Glass transition exhibits a small shift to higher temperatures in composites, which also exhibit increased char formation—at lower filler content for the composite with unmodified nanoparticles and at higher for the one with modified nanoparticles. All composites show improved mechanical properties in comparison with the neat epoxy. For the unmodified particles, strength and modulus are particularly improved at lower nanofiller content due to their better dispersion, as observed by SEM. The modified nanoparticles contributed to a significant increase in elongation at break, increasing the toughness of the cured resin while retaining its strength and without having an adverse influence on the modulus.

This is a preview of subscription content, access via your institution.

Access options

Buy single article

Instant access to the full article PDF.

USD 39.95

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8

References

  1. Yee AF, Pearson RA. Toughening mechanisms in elastomer-modified epoxies—part 1 mechanical studies. J Mater Sci. 1986;21:2462–74.

    CAS  Article  Google Scholar 

  2. Bucknall CB, Gilbert AH. Toughening tetrafunctional epoxy resins using polyetherimide. Polymer. 1989;30:213–7.

    CAS  Article  Google Scholar 

  3. Gojny FH, Wichmann MHG, Köpke U, Fiedler B, Schulte K. Carbon nanotube-reinforced epoxy-composites: enhanced stiffness and fracture toughness at low nanotube content. Compos Sci Technol. 2004;64:2363–71.

    CAS  Article  Google Scholar 

  4. Hodgkin JH, Simon GP, Varley RJ. Thermoplastic toughening of epoxy resins: a critical review. Polym Adv Technol. 1998;9:3–10.

    CAS  Article  Google Scholar 

  5. Frigione ME, Mascia L, Acierno D. Oligomeric and polymeric modifiers for toughening of epoxy resins. Eur Polym J. 1995;31:1021–9.

    CAS  Article  Google Scholar 

  6. Lebaron PC, Wang Z, Pinnavaia TJ. Polymer-layered silicate nanocomposites: an overview. Appl Clay Sci. 1999;15:11–29.

    CAS  Article  Google Scholar 

  7. Tjong SC. Structural and mechanical properties of polymer nanocomposites. Mater Sci Eng R. 2006;53:73–197.

    Article  Google Scholar 

  8. Battistella M, Cascione M, Fielder B, Wichmann MHG, Quaresimin M, Schulte K. Fracture behaviour of fumed silica/epoxy nanocomposites. Compos A. 2008;39:1851–8.

    Article  Google Scholar 

  9. Baller J, Becker N, Ziehmer M, Thomassey M, Zielinski B, Müller U, Sanctuary R. Interactions between silica nanoparticles and an epoxy resin before and during network formation. Polymer. 2009;50:3211–9.

    CAS  Article  Google Scholar 

  10. Vrsaljko D, Macut D, Kovačević V. Potential role of nanofillers as compatibilizers in immiscible PLA/LDPE blends. J Appl Polym Sci. 2015;132:41414.

    Article  Google Scholar 

  11. Barabanova AI, Philippova OE, Askadskii AA, Khokhlov AR. Transparent epoxy/silica nanocomposites with increased glass transition temperatures. Procedia Chem. 2012;4:352–9.

    CAS  Article  Google Scholar 

  12. Blackman BRK, Kinloch AJ, Sohn Lee J, Taylor AC, Agarwal R, Schueneman G, Sprenger S. The fracture and fatigue behaviour of nano-modified epoxy polymers. J Mater Sci. 2007;42:7049–51.

    CAS  Article  Google Scholar 

  13. Bondioli F, Cannillo V, Fabbri E, Messori M. Epoxy-silica nanocomposites: preparation, experimental characterization, and modeling. J Appl Polym Sci. 2005;97:2382–6.

    CAS  Article  Google Scholar 

  14. Jumahat A, Soutis C, Jones FR, Hodzic A. Effect of silica nanoparticles on compressive properties of an epoxy polymer. J Mater Sci. 2010;45:5973–83.

    CAS  Article  Google Scholar 

  15. Rosso P, Ye L, Friedrich K, Sprenger S. A toughened epoxy resin by silica nanoparticle reinforcement. J Appl Polym Sci. 2006;100:1849–55.

    CAS  Article  Google Scholar 

  16. Wichmann MHG, Cascione M, Fiedler B, Quaresimin M, Schulte K. Influence of surface treatment on mechanical behaviour of fumed silica/epoxy resin nanocomposites. Compos Interfaces. 2006;13:699–715.

    CAS  Article  Google Scholar 

  17. Zhuravlev LT. The surface chemistry of amorphous silica. Zhuravlev model. Colloids Surf A. 2000;173:1–38.

    CAS  Article  Google Scholar 

  18. Domingo C, Loste E, Fraile J. Grafting of trialkoxysilane on the surface of nanoparticles by conventional wet alcoholic and supercritical carbon dioxide deposition methods. J Supercrit Fluids. 2006;37:72–86.

    CAS  Article  Google Scholar 

  19. Li X, Cao Z, Zhang Z, Dang H. Surface-modification in situ of nano-SiO2 and its structure and tribological properties. Appl Surf Sci. 2006;252:7856–61.

    CAS  Article  Google Scholar 

  20. Hoebbel D, Nacken M, Schmidt H. The effect of nanoscaled metal oxide sols on the structure and properties of glycidoxypropyltrimethoxysilane derived sols and gels. J Sol–Gel Sci Technol. 2000;19:305–9.

    CAS  Article  Google Scholar 

  21. Underhill PR, Goring G, Duquesnay DL. A study of the deposition of 3-glycidoxypropyltrimethoxysilane on aluminum. Int J Adhes Adhes. 1998;18:307–11.

    CAS  Article  Google Scholar 

  22. Daniels MW, Francis LF. Silane adsorption behavior, microstructure, and properties of glycidoxypropyltrimethoxysilane-modified colloidal silica coatings. J Colloid Interface Sci. 1998;205:191–200.

    CAS  Article  Google Scholar 

  23. Chu L, Daniels MW, Francis LF. Use of (glycidoxypropyl)trimethoxysilane as a binder in colloidal silica coatings. Chem Mater. 1997;9:2577–82.

    CAS  Article  Google Scholar 

  24. Antonelli C, Serrano B, Baselga J, Ozisik R, Cabanelas JC. Interfacial characterization of epoxy/silica nanocomposites measured by fluorescence. Eur Polym J. 2015;62:31–42.

    CAS  Article  Google Scholar 

  25. Fadeev AY, McCarthy TJ. Self-assembly is not the only reaction possible between alkyltrichlorosilanes and surfaces: monomolecular and oligomeric covalently attached layers of dichloro- and trichloroalkylsilanes on silicon. Langmuir. 2000;16:7268–74.

    CAS  Article  Google Scholar 

  26. Dugas V, Chevalier Y. Surface hydroxylation and silane grafting on fumed and thermal silica. J Colloid Interface Sci. 2003;264:354–61.

    CAS  Article  Google Scholar 

  27. van der Voort P, Vansant EF. Silylation of the silica surface: a review. J Liq Chromatogr Relat Technol. 1996;19:2723–31.

    Article  Google Scholar 

  28. Sangermano M, Malucelli G, Amerio E, Priola A, Billi E, Rizza G. Photopolymerization of epoxy coatings containing silica nanoparticles. Prog Organ Coat. 2005;54:134–8.

    CAS  Article  Google Scholar 

  29. Ragosta G, Abbate M, Musto P, Scarinzi G, Mascia L. Epoxy-silica particulate nanocomposites: chemical interactions, reinforcement and fracture toughness. Polymer. 2005;46:10506–16.

    CAS  Article  Google Scholar 

  30. Gholamian F, Ghariban-Lavasani S, Garshasbi MM, Ansari M, Bataghv F, Moraveji A, Ranjbar Z. The effects of water absorption and surface treatment on mechanical properties of epoxy nanocomposite using response surface methodology. Polym Bull. 2013;70:1677–95.

    CAS  Article  Google Scholar 

  31. Liu G, Zhang H, Zhang D, Zhang H, Zhang Z, An X, Yi X. On depression of glass transition temperature of epoxy nanocomposites. J Mater Sci. 2012;47:6891–5.

    CAS  Article  Google Scholar 

  32. Zappalorto M, Pontefisso A, Fabrizi A, Quaresimin M. Mechanical behaviour of epoxy/silica nanocomposites: experiments and modelling. Compos A. 2015;72:58–64.

    CAS  Article  Google Scholar 

  33. Liu YL, Hsu CY, Wei WL, Jeng RJ. Preparation and thermal properties of epoxy-silica nanocomposites from nanoscale colloidal silica. Polymer. 2003;44:5159–67.

    CAS  Article  Google Scholar 

  34. Johnsen BB, Kinloch AJ, Mohammed RD, Taylor AC, Sprenger S. Toughening mechanisms of nanoparticle-modified epoxy polymers. Polymer. 2007;48:530–41.

    CAS  Article  Google Scholar 

  35. Rosso P, Ye L. Epoxy/silica nanocomposites: nanoparticle-induced cure kinetics and microstructure. Macromol Rapid Commun. 2007;28:121–6.

    CAS  Article  Google Scholar 

  36. Rivers G, Rogalsky A, Lee-Sullivan P, Zhao B. Thermal analysis of epoxy-based nanocomposites: Have solvent effects been overlooked? J Therm Anal Calorim. 2015;119:797–805.

    CAS  Article  Google Scholar 

  37. Hsieh TH, Kinloch AJ, Masania K, Taylor AC, Sprenger S. The mechanisms and mechanics of the toughening of epoxy polymers modified with silica nanoparticles. Polymer. 2010;51:6284–94.

    CAS  Article  Google Scholar 

  38. Bray DJ, Dittanet P, Guild FJ, Kinloch AJ, Masania K, Pearson RA, Taylor AC. The modelling of the toughening of epoxy polymers via silica nanoparticles: the effects of volume fraction and particle size. Polymer. 2013;54:7022–32.

    CAS  Article  Google Scholar 

  39. Prolongo MG, Salom C, Arribas C, Sánchez-Cabezudo M, Masegosa RM, Prolongo SG. Influence of graphene nanoplatelets on curing and mechanical properties of graphene/epoxy nanocomposites. J Therm Anal Calorim. 2016;125:629–36.

    CAS  Article  Google Scholar 

  40. Marouf BT, Mai Y-W, Bagheri R, Pearson RA. Toughening of epoxy nanocomposites: nano and hybrid effects. Polym Rev. 2016;56:70–112.

    CAS  Article  Google Scholar 

  41. Liang YL, Pearson RA. Toughening mechanisms in epoxy–silica nanocomposites (ESNs). Polymer. 2009;50:4895–905.

    CAS  Article  Google Scholar 

  42. Bittmann B, Haupert F, Schlarb AK. Ultrasonic dispersion of inorganic nanoparticles in epoxy resin. Ultrason Sonochem. 2009;16:622–8.

    CAS  Article  Google Scholar 

  43. Zhang H, Tang LC, Zhang Z, Friedrich K, Sprenger S. Fracture behaviours of in situ silica nanoparticle-filled epoxy at different temperatures. Polymer. 2008;49:3816–25.

    CAS  Article  Google Scholar 

Download references

Acknowledgements

This study is a part of the research project “Bioceramic, Polymer and Composite Nanostructured Materials”, 125-1252970-3005, supported by the Ministry of Science, Education and Sports of the Republic of Croatia. The authors are grateful to Prof. Đ. Španiček and Mr. B. Bušetinčan from Faculty of Mechanical Engineering and Naval Architecture, University of Zagreb, for the ball indentation measurements.

Author information

Author notes

  1. Bruno Burmas

    Present address: Faculty of Natural Sciences and Technology, Norwegian University of Science and Technology, 7491, Trondheim, Norway

Authors and Affiliations

  1. Faculty of Chemical Engineering and Technology, University of Zagreb, Marulićev trg 19, 10000, Zagreb, Croatia

    Jelena Macan, Klaudia Paljar, Bruno Burmas, Goran Špehar & Mirela Leskovac

  2. Ruđer Bošković Institute, Bijenička 54, 10000, Zagreb, Croatia

    Andreja Gajović

Authors
  1. Jelena Macan
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Klaudia Paljar
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Bruno Burmas
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Goran Špehar
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Mirela Leskovac
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Andreja Gajović
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Jelena Macan.

Rights and permissions

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Macan, J., Paljar, K., Burmas, B. et al. Epoxy-matrix composites filled with surface-modified SiO2 nanoparticles. J Therm Anal Calorim 127, 399–408 (2017). https://doi.org/10.1007/s10973-016-5976-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10973-016-5976-7

Keywords

  • Epoxy
  • Silica nanoparticles
  • Surface modification
  • Thermal properties
  • Toughening