Abstract
Under conventional temperature regimes, optical fiber sensors (OFS) have been extensively utilized for real-time monitoring of strain and temperature responses in transportation, energy, and civil engineering structures. However, in low-temperature environments, OFS applications confront challenges such as poor adhesion, diminished sensitivity, weak signal transmission, and complex compensation requirements. Therefore, it is crucial to conduct in-depth research on the high-precision calibration characteristics of strain and temperature in cryogenic conditions. In this study, we propose an enhanced calibration technique for fiber Bragg grating (FBG) strain/temperature sensitivity, covering a low-temperature range of 77–296 K. Employing a custom-designed low-temperature testing apparatus, we calibrated the thermo-optic coefficients, temperature, and strain sensitivity coefficients. Subsequently, this improved method was applied to measure the coefficient of thermal expansion of various materials. The results confirm the accuracy of the proposed method and present the strain/temperature measurement properties of FBG. This research provides guidance for the precise use of FBG in low-temperature environments.
Similar content being viewed by others
References
R. Rajinikumar et al., Design parameter evaluation of a metal recoated Fiber Bragg Grating sensors for measurement of cryogenic temperature or stress in superconducting devices. Cryogenics 49(5), 202–209 (2009)
W. Hong et al., A cryogenic sensor based on fiber Bragg grating for storage monitoring of liquefied natural gas. Cryogenics 97, 7–12 (2019)
M. Guinchard et al., Mechanical strain measurements based on fiber Bragg grating down to cryogenic temperature-R&D Study and applications. In: 9th International Particle Accelerator Conference. 2018
C. Ferrero, C. Marinari, E. Martino, Calibration systems for strain gauges to be used at cryogenic temperatures. Sens. Actuators A 31(1–3), 125–129 (1992)
P. Lu et al. Distributed optical fiber sensing: Review and perspective. Appl. Phys. Rev. 6.4, 041302 (2019).
D. Sengupta et al., Strain-temperature discrimination using a single FBG at cryogenic region. Sensors & Transducers 131(8), 36 (2011)
J. Roths et al., Calibration of fiber Bragg cryogenic temperature sensors (Optical Society of America, Optical Fiber Sensors, 2006)
V. N. Venkatesan et al. Strain calibration of substrate-Free FBG sensors at cryogenic temperature. International Internet of Things Summit. Springer, Cham (2015)
X. Lu, M.A. Soto, L. Thévenaz, Impact of the fiber coating on the temperature response of distributed optical fiber sensors at cryogenic ranges. J. Lightwave Technol. 36(4), 961–967 (2017)
Y. Kwon, et al. Enhanced sensitivity of distributed-temperature sensor with Al-coated fiber based on OFDR. Opt. Fiber Technol. 48, 229–234 (2019)
M. Zaynetdinov et al. A fiber Bragg grating temperature sensor for 2–400 K. IEEE Sensors J. 15.3, 1908–1912 (2014)
L. Li, et al. Strain characteristics of the silica-based fiber Bragg gratings for 30–273 K. Cryogenics 92, 93–97 (2018).
V. N. Venkatesan, R. Ramalingam. Numerical and experimental investigation of FBG strain response at cryogenic temperatures. IOP Conference Series: Materials Science and Engineering. Vol. 171. No. 1. IOP Publishing (2017)
W. R. Habel, G. S. Vivien, and K. Nadine. Calibration facility for quality certification of surface-attached fiber optic and electrical strain sensors. Sensors (2011)
R. Tan, et al. High-precision calibration method for fiber Bragg grating strain sensing based on an optical lever. Opt. Fiber Technol. 61, 102392 (2021)
H. Wang, J.-G. Dai, Strain transfer analysis of fiber Bragg grating sensor assembled composite structures subjected to thermal loading. Compos. B Eng. 162, 303–313 (2019)
T. Yang, H. Wang, X. Wang, Strain transfer characteristics of multi-layer optical fiber sensors with temperature-dependent properties at low temperature. Sensors 21(2), 495 (2021)
A.A. Stolov, D.A. Simoff, J. Li, Thermal stability of specialty optical fibers. J. Lightwave Technol. 26(20), 3443–3451 (2008)
E.A.S. Marques et al., Adhesive joints for low-and high-temperature use: an overview. J. Adhes. 91(7), 556–585 (2015)
J. Roths, J. Florian. Determination of strain sensitivity of free fiber Bragg gratings. Optical Sensors 2008. Vol. 7003. International Society for Optics and Photonics, 2008.
E. D. Marquardt, J. P. Le, and R. Radebaugh. Cryogenic material properties database. Cryocoolers 11, 681–687 (2002).
G.B. Chen, Cryogenic Engineering Materials (Zhejiang University Press, China, 1998)
Acknowledgements
This work was supported by National Key Research and Development Program of China (2019YBB1504400).
Author information
Authors and Affiliations
Contributions
TY completed the experiment, theoretical research, and initial draft of the article. SL and YY made revisions to the article and verified the data, while XG and TT verified the theory and charts of the article. All authors reviewed the manuscript.
Corresponding author
Ethics declarations
Conflict of interest
The authors have no competing interests to declare that are relevant to the content of this article.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Yang, T., Liu, S., Yang, Y. et al. Optimized Cryogenic FBG Sensitivity Coefficient Calibration for High-Precision Thermal Expansion Measurements. J Low Temp Phys 213, 107–120 (2023). https://doi.org/10.1007/s10909-023-02980-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10909-023-02980-4