Abstract
As one of the key technologies for high performance electronic devices, composite solders have been recently developed to improve thermal and mechanical properties of solder joints. In this study, accumulative roll bonding process was used as an effective alternative method for manufacturing high-strength, finely dispersed, void-free and highly uniform Sn–Ag–Cu/CeO2 nanocomposite solders. Microstructural investigation of nanocomposite solders revealed that homogenous distribution of CeO2 nanoparticle has been achieved and the eutectic as-cast morphology of the solder changed to recrystallized fine grained structure. As a result of severe plastic deformation during rolling, brittle and elongated intermetallics crushed into fine particles with an average diameter of a few hundred nanometers and dispersed uniformly in the solder matrix. Mechanical test results showed that the microhardness, 0.2% yield stress, and ultimate tensile strength of the composite solder increased with addition of CeO2 nanoparticles, while the ductility of the composite was decreased.
Similar content being viewed by others
References
Y.C. Chan, D. Yan, Prog. Mater. Sci. 55, 428–475 (2010)
J. Shen, Y.C. Chan, Microelectron. Reliab. 49, 223–234 (2009)
F. Guo, J. Mater. Sci.: Mater. Electron. 18, 129–145 (2007)
J. Shen, Y.C. Liu, Y.J. Han, Y.M. Tian, H.X. Gao, strengthening effects of zro2 nanoparticles on the microstructure and microhardness of Sn-3.5ag lead-free solder. J. Elec. Mater. 35, 1672–1679 (2006)
L.C. Tsao, S.Y. Chang, Mater. Des. 31, 990–993 (2010)
X. Wang, Y.C. Liu, C. Wei, H.X. Gao, P. Jiang, L.M. Yu, J. Alloys Compd. 480, 662–665 (2009)
P. Babaghorbani, S.M.L. Nai, M. Gupta, J. Mater. Sci.: Mater. Electron. 20, 571–576 (2008)
R. Jamaati, M. Toroghinejad, Mater. Sci. Eng. A 527, 7430–7435 (2010)
M. Göken, H.W. Höppel, Adv. Mater. 23, 2663–2668 (2011)
C.W. Schmidt, C. Knieke, V. Maier, H.W. Höppel, W. Peukert, M. Göken, Scripta Materialia 64, 245–248 (2011)
M. Alizadeh, M.H. Paydar, J. Alloys Compd. 492, 231 (2010)
S. Hwang, J. Lee, Z. Lee, J. Electron. Mater. 31, 1304–1308 (2002)
L. Li, K. Nagai, F. Yin, Sci. Technol. Adv. Mater. 9, 1–11 (2008)
J. Bath, Lead-free soldering (Springer Science & Business Media, LLC, 2007), pp. 6–30
L.R. Vaidyanath, M.G. Nicholas, D.R. Milner, British Weld J. 6, 13–28 (1959)
N. Tsuji, Y. Ito, Y. Saito, Y. Minamino, Scripta Mater. 47, 893–899 (2002)
K.N. Subramanian, Lead-free electronic solders a special issue of the Journal of Materials Science: Materials in Electronic (Springer Science + Business Media, LLC, 2007)
P. Lauro, S.K. Kang, W. Kyoung Choi, D. Shih, J. Electron. Mater. 32, 1432–1440 (2003)
G. Krallics, J.G. Lenard, J. Mater. Process. Technol. 152, 154–161 (2004)
Q. F. Wang, X. P. Xiao, J. Hu, W. W Xu, X.Q. Zhao, S. J. Zhao, in Proceedings of Sino-Swedish Structural Materials Symuosium, 2007
P. Babaghorbania, S.M.L. Nai, M. Gupta, J. Alloys Compd. 478, 458–461 (2009)
K. Sandar Tuna, M. Gupta, Compos. Sci. Technol. 67, 2657–2664 (2007)
T.W. Clyne, P.J. Withers, An introduction to metal matrix composites (Cambridge University Press, Cambridge, 1993)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Roshanghias, A., Kokabi, A.H., Miyashita, Y. et al. Ceria reinforced nanocomposite solder foils fabricated by accumulative roll bonding process. J Mater Sci: Mater Electron 23, 1698–1704 (2012). https://doi.org/10.1007/s10854-012-0648-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10854-012-0648-2