Skip to main content
SpringerLink
Log in

Improvement of mechanical properties and thermal conductivity of carbon fiber laminated composites through depositing graphene nanoplatelets on fibers

  • Composites
  • Published:
Journal of Materials Science Aims and scope Submit manuscript

Abstract

In this study, a graphene nanoplatelets (GnPs)/acetone solution containing a small amount of resin/hardener was prepared as the spraying solution for modifying dry fabrics which are well compatible with the vacuum-assisted resin transfer infusion (VARI) process, and the GnPs-reinforced fiber laminated composites with GnPs uniformly distributed in the interlaminar regions were successfully fabricated. The results showed that the GnPs are well immobilized on the surface of carbon fibers after spray coating, and the mechanical properties and thermal conductivity of the carbon fiber/epoxy composites were effectively improved. The incorporation of 0.3 wt% GnPs produced the largest flexural strength and interlaminar shear strength, and the reinforcing mechanisms as well as failure modes of the composites were proposed. It was also noticed that the through-plane thermal conductivity of the composites consistently increases with increasing GnPs content due to the formation of effective conductive pathways between the interplies. The study suggested that the developed up-scalable spraying technique is an effective approach to deposit GnPs on dry carbon fabrics which are compatible with the economical VARI process for producing GnPs/fiber/epoxy multiscale composites with enhanced properties.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13

Similar content being viewed by others

References

  1. Chand S (2000) Carbon fibers for composites. J Mater Sci 35:1303–1313. https://doi.org/10.1023/A:1004780301489

    Article  Google Scholar 

  2. Chae HG, Kumar S (2008) Materials science-making strong fibers. Science 319:908–909

    Article  Google Scholar 

  3. Mirjalili V, Ramachandramoorthy R, Hubert P (2014) Enhancement of fracture toughness of carbon fiber laminated composites using multi wall carbon nanotubes. Carbon 79:413–423

    Article  Google Scholar 

  4. Kandare E, Khatibi AA, Yoo S, Wang RY, Ma J, Olivier P, Gleizes N, Wang CH (2015) Improving the through-thickness thermal and electrical conductivity of carbon fibre/epoxy laminates by exploiting synergy between graphene and silver nano-inclusions. Compos Part A Appl Sci Manuf 69:72–82

    Article  Google Scholar 

  5. Liu Y, Yang JP, Xiao HM, Qu CB, Feng QP, Fu SY, Shindo Y (2012) Role of matrix modification on interlaminar shear strength of glass fibre/epoxy composites. Compos Part B Eng 43:95–98

    Article  Google Scholar 

  6. Haghbin A, Liaghat GH, Arabi AM, Hadavinia H, Pol MH (2018) Investigations on electrophoretic deposition of carbon nanotubes on glass textures to improve polymeric composites interface. Compos Sci Technol 155:197–204

    Article  Google Scholar 

  7. Guo J, Zhang QJ, Gao L, Zhong WH, Sui G, Yang XP (2017) Significantly improved electrical and interlaminar mechanical properties of carbon fiber laminated composites by using special carbon nanotube pre-dispersion mixture. Compos Part A Appl Sci Manuf 95:294–303

    Article  Google Scholar 

  8. El Moumen A, Tarfaoui M, Lafdi K, Benyahia H (2017) Dynamic properties of carbon nanotubes reinforced carbon fibers/epoxy textile composites under low velocity impact. Compos Part B Eng 125:1–8

    Article  Google Scholar 

  9. El Moumen A, Tarfaoui M, Lafdi K (2017) Mechanical characterization of carbon nanotubes based polymer composites using indentation tests. Compos Part B Eng 114:1–7

    Article  Google Scholar 

  10. Tarfaoui M, Lafdi K, El Moumen A (2016) Mechanical properties of carbon nanotubes based polymer composites. Compos Part B Eng 103:113–121

    Article  Google Scholar 

  11. El Moumen A, Tarfaoui M, Hassoon O, Lafdi K, Benyahia H, Nachtane M (2018) Experimental study and numerical modelling of low velocity impact on laminated composite reinforced with thin film made of carbon nanotubes. Appl Compos Mater 25:309–320

    Article  Google Scholar 

  12. El Moumen A, Tarfaoui M, Lafdi K (2018) Computational homogenization of mechanical properties for laminate composites reinforced with thin film made of carbon nanotubes. Appl Compos Mater 25:569–588

    Article  Google Scholar 

  13. Lee C, Wei X, Kysar JW, Hone J (2008) Measurement of the elastic properties and intrinsic strength of monolayer graphene. Science 321:385–388

    Article  Google Scholar 

  14. Balandin AA, Ghosh S, Bao W, Calizo I, Teweldebrhan D, Miao F, Lau CN (2008) Superior thermal conductivity of single-layer graphene. Nano Lett 8:902–907

    Article  Google Scholar 

  15. Du X, Skachko I, Barker A, Andrei EY (2008) Approaching ballistic transport in suspended graphene. Nat Nanotechnol 3:491–495

    Article  Google Scholar 

  16. Zhang X, Fan X, Yan C, Li H, Zhu Y, Li X, Yu L (2012) Interfacial microstructure and properties of carbon fiber composites modified with graphene oxide. ACS Appl Mater Interfaces 4:1543–1552

    Article  Google Scholar 

  17. Adak NC, Chhetri S, Murmu NC, Samanta P, Kuila T, Lee JH (2019) Experimental and numerical investigation on the mechanical characteristics of polyethylenimine functionalized graphene oxide incorporated woven carbon fibre/epoxy composites. Compos Part B Eng 156:240–251

    Article  Google Scholar 

  18. Hung PY, Lau KT, Fox B, Hameed N, Lee JH, Hui D (2018) Surface modification of carbon fibre using graphene–related materials for multifunctional composites. Compos Part B Eng 133:240–257

    Article  Google Scholar 

  19. Drzal LT, Fukushima H (2006) Expanded graphite and products produced therefrom. U.S. Patent (US 8501858 B2)

  20. Wang FZ, Drzal LT, Qin Y, Huang ZX (2015) Multifunctional graphene nanoplatelets/cellulose nanocrystals composite paper. Compos Part B Eng 79:521–529

    Article  Google Scholar 

  21. Wang FZ, Drzal LT, Qin Y, Huang ZX (2015) Mechanical properties and thermal conductivity of graphene nanoplatelets/epoxy nanocomposites. J Mater Sci 50:1082–1093. https://doi.org/10.1016/j.cplett.2012.02.006

    Article  Google Scholar 

  22. Shen X, Wang ZY, Wu Y, Liu X, He YB, Kim JK (2016) Multilayer graphene enables higher efficiency in improving thermal conductivities of graphene/epoxy composites. Nano Lett 16:3585–3593

    Article  Google Scholar 

  23. Wang FZ, Drzal LT, Qin Y, Huang ZX (2016) Enhancement of fracture toughness, mechanical and thermal properties of rubber/epoxy composites by incorporation of graphene nanoplatelets. Compos Part A Appl Sci Manuf 87:10–22

    Article  Google Scholar 

  24. Ahmadi-Moghadam B, Taheri F (2014) Effect of processing parameters on the structure and multi-functional performance of epoxy/GNP-nanocomposites. J Mater Sci 49:6180–6190. https://doi.org/10.1007/s10853-014-8332-y

    Article  Google Scholar 

  25. Qin WZ, Vautard F, Drzal LT, Yu JR (2015) Mechanical and electrical properties of carbon fiber composites with incorporation of graphene nanoplatelets at the fiber-matrix interphase. Compos Part B Eng 69:335–341

    Article  Google Scholar 

  26. Ahmadi-Moghadam B, Taheri F (2015) Influence of graphene nanoplatelets on modes I, II and III interlaminar fracture toughness of fiber-reinforced polymer composites. Eng Fract Mech 143:97–107

    Article  Google Scholar 

  27. Zhang KM, Gu YZ, Li M, Zhang ZG (2014) Effect of rapid curing process on the properties of carbon fiber/epoxy composite fabricated using vacuum assisted resin infusion molding. Mater Des 54:624–631

    Article  Google Scholar 

  28. Bender D, Schuster J, Heider D (2006) Flow rate control during vacuum-assisted resin transfer molding (VARTM) processing. Compos Sci Technol 66:2265–2271

    Article  Google Scholar 

  29. Zhang H, Liu Y, Huo SS, Briscoe J, Tu W, Picot OT, Rezai A, Bilotti E, Peijs T (2017) Filtration effects of graphene nanoplatelets in resin infusion processes: Problems and possible solutions. Compos Sci Technol 139:138–145

    Article  Google Scholar 

  30. Shan FL, Gu YZ, Li M, Liu NY, Zhang ZG (2013) Effect of deposited carbon nanotubes on interlaminar properties of carbon fiber-reinforced epoxy composites using a developed spraying processing. Polym Compos 34:41–50

    Article  Google Scholar 

  31. Adak NC, Chhetri S, Kuila T, Murmu NC, Samanta P, Lee JH (2018) Effects of hydrazine reduced graphene oxide on the inter-laminar fracture toughness of woven carbon fiber/epoxy composite. Compos Part B Eng 149:22–30

    Article  Google Scholar 

  32. Jia JJ, Du XS, Chen C, Sun XY, Mai YW, Kim JK (2015) 3D network graphene interlayer for excellent interlaminar toughness and strength in fiber reinforced composites. Carbon 95:978–986

    Article  Google Scholar 

  33. Wang FZ, Drzal LT, Qin Y, Huang ZX (2016) Effects of functionalized graphene nanoplatelets on the morphology and properties of epoxy resins. High Perform Polym 28:1–7

    Google Scholar 

  34. Li F, Liu Y, Qu CB, Xiao HM, Hua Y, Sui GX, Fu SY (2015) Enhanced mechanical properties of short carbon fiber reinforced polyethersulfone composites by graphene oxide coating. Polymer 59:155–165

    Article  Google Scholar 

  35. Stankovich S, Dikin DA, Piner RD, Kohlhaas KA, Kleinhammes A, Jia Y, Wu Y, Nguyen ST, Ruoff RS (2007) Synthesis of graphene-based nanosheets via chemical reduction of exfoliated graphite oxide. Carbon 45:1558–1565

    Article  Google Scholar 

  36. Zhang Q, Xu X, Li H, Xiong G, Hu H, Fisher TS (2015) Mechanically robust honeycomb graphene aerogel multifunctional polymer composites. Carbon 93:659–670

    Article  Google Scholar 

  37. Halpin J (1969) Stiffness and expansion estimates for oriented short fiber composites. J Compos Mater 3:732–734

    Article  Google Scholar 

  38. Mori T, Tanaka K (1973) Average stress in matrix and average elastic energy of materials with misfitting inclusions. Acta Metall 21:571–574

    Article  Google Scholar 

  39. Cox H (1952) The elasticity and strength of paper and other fibrous materials. Br J Appl Phys 3:72–79

    Article  Google Scholar 

  40. Gao XL, Li K (2005) A shear-lag model for carbon nanotube-reinforced polymer composites. Int J Solids Struct 42:1649–1667

    Article  Google Scholar 

  41. Wang FZ, Drzal LT, Qin Y, Huang ZX (2016) Size effect of graphene nanoplatelets on the morphology and mechanical behavior of glass fiber/epoxy composites. J Mater Sci 51:3337–3348. https://doi.org/10.1007/s10853-015-9649-x

    Article  Google Scholar 

  42. Zhang RL, Gao B, Du WT, Zhang J, Cui HZ, Liu L, Ma QH, Wang CG, Li FH (2016) Enhanced mechanical properties of multiscale carbon fiber/epoxy composites by fiber surface treatment with graphene oxide/polyhedral oligomeric silsesquioxane. Compos Part A Appl Sci Manuf 84:455–463

    Article  Google Scholar 

  43. Khan SU, Kim JK (2012) Improved interlaminar shear properties of multiscale carbon fiber composites with bucky paper interleaves made from carbon nanofibers. Carbon 50:5265–5277

    Article  Google Scholar 

  44. Rafiee MA, Rafiee J, Srivastava I, Wang Z, Song H, Yu ZZ, Koratkar N (2010) Fracture and fatigue in graphene nanocomposites. Small 6:179–183

    Article  Google Scholar 

  45. Chandrasekaran S, Sato N, Tölle F, Mülhaupt R, Fiedler B, Schulte K (2014) Fracture toughness and failure mechanism of graphene based epoxy composites. Compos Sci Technol 97:90–99

    Article  Google Scholar 

  46. Kuo WS, Tai NH, Chang TW (2013) Deformation and fracture in graphene nanosheets. Compos Part A Appl Sci Manuf 51:56–61

    Article  Google Scholar 

  47. Shen XJ, Meng LX, Yan ZY, Sun CJ, Ji YH, Xiao HM, Fu SY (2015) Improved cryogenic interlaminar shear strength of glass fabric/epoxy composites by graphene oxide. Compos Part B Eng 73:126–131

    Article  Google Scholar 

  48. Yang JP, Yang G, Xu GH, Fu SY (2007) Cryogenic mechanical behaviors of MMT/epoxy nanocomposites. Compos Sci Technol 67:2934–2940

    Article  Google Scholar 

  49. Han X, Zhao Y, Sun JM, Li Y, Zhang JD, Hao Y (2017) Effect of graphene oxide addition on the interlaminar shear property of carbon fiber-reinforced epoxy composites. New Carbon Mater 32:48–55

    Article  Google Scholar 

  50. Nika DL, Balandin AA (2017) Phonons and thermal transport in graphene and graphene-based materials. Rep Prog Phys 80:036502

    Article  Google Scholar 

Download references

Acknowledgements

The authors acknowledge the financial support from Science Foundation of Shandong Province, China (Grant No. ZR2017QEM001).

Author information

Authors and Affiliations

  1. Advanced Materials Institute, School of Materials Science and Engineering, Qilu University of Technology (Shandong Academy of Sciences), Jinan, 250353, China

    Fuzhong Wang & Xiaoxia Cai

Authors
  1. Fuzhong Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Xiaoxia Cai
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Fuzhong Wang.

Ethics declarations

Conflicts of interest

The authors declare that they have no conflicts of interest.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Wang, F., Cai, X. Improvement of mechanical properties and thermal conductivity of carbon fiber laminated composites through depositing graphene nanoplatelets on fibers. J Mater Sci 54, 3847–3862 (2019). https://doi.org/10.1007/s10853-018-3097-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10853-018-3097-3

Keywords

Search

Navigation