Abstract
Local melting and tool slippage during friction stir spot welding of different Al-alloy base materials is examined using a combination of detailed microscopy and temperature measurement. The stir zone peak temperature during welding is limited by either the solidus of the alloy in question or by spontaneous melting of intermetallic particles contained in the as-received base material. When spontaneous melting occurs this facilitates tool slippage at the contact interface. Accurate stir zone temperature and grain size measurements are essential elements when estimating the strain rate using the Zener–Hollomon relation. In Al 2024 and Al 7075 spot welds spontaneous melting of second-phase particles produces a drastic reduction in strain rate values. In Al 5754 and Al 6061 spot welds there is a strong correlation between tool rotational speed and estimated strain values. Local melted films dissolve rapidly in the high temperature stir zone and when the spot weld cools to room temperature following welding. Evidence of local melting is observed in Al 7075 friction stir spot welded joints made using a combination of rapid quenching, high plunge rates, and extremely short dwell time settings.
Similar content being viewed by others
References
Thomas WM, Nicholas ED, Needham JD, Murch MG, Templesmith P, Dawes CJ (1991/1995) G.B. Patent Application No. 9125978.8, Dec. 1991; U.S. Patent No. 5460317, Oct. 1995
Schilling C, Dos Santos J (2001) International Patent Publication No. WO 01/36144A1, May 25, 2001
Gerlich A, Su P, North TH (2005) J Mater Sci 40(24):6473
Sakano R, Murakami K, Yamashita K, Hyoie T, Fujimoto M, Inuzuka M, Nagao Y, Kashiki H (2001) Proc 7th Int Symp JWS 645
Lin P-C, Lin S-H, Pan J, Pan T, Nicholson JM, Garman MA (2004) SAE Technical Series, 2004-01-1330
Su P, Gerlich A, North TH (2005) SAE Technical Series, 2005-01-1255
Gerlich A, Avramovic-Cingara G, North TH (2006) Metall Trans A 37A:2773
Gerlich A, Su P, Yamamoto M, North TH (2007) J Mater Sci. doi:10.1007/s10853-006-1103-7
Su P, Gerlich A, North TH, Bendzsak GJ (2006) Sci Tech Weld Joining 11(2):163
Su P, Gerlich A, North TH, Bendzsak GJ (2006) SAE Technical Series, 2006-01-0971
Gerlich A, Su P, North TH (2005) Sci Tech Weld Joining 10(6):647
Gerlich A, Su P, North TH, Bendzsak GJ (2005) In: Nie JF, Barnett M (eds) Materials forum, vol 29, p 290
Gerlich A, Su P, North TH (2005) In: Neelameggham NR, Kaplan HI, Powell BR (eds) Magnesium technology 2005, TMS, p 383
North TH, Bendzsak GJ, Smith CB, Luan GH (2001) Proceedings of the 7th International Symposium on JWS. JWS, Japan, p 621
Gerlich A, Yamamoto M, North TH (2007) Metall Trans A accepted March 6, 2007
Dalle-Donne C, Braun B, Staniek G, Jung A, Kayser WA (1998) Materialwiss Werkstofftech 29:609
North TH, Bendzsak GJ, Smith CB (2000) Proceedings of 2nd international conference on friction stir welding. TWI, Gothenburg
Sato YS, Hwan S, Park C, Michiuchi M, Kokawa H (2004) Scr Mater 50(9):1233
Bendzsak GJ, North TH, Smith CB (2000) Proceedings of 2nd international conference on friction stir welding. TWI, Gothenburg
Droenen P-E, Ryum N (1994) Metall Trans A 25A:521
Bjørneklett B, Frigaard Ø, Grong Ø, Myhr OR, Midling OT (1999) Proceedings of 6th international conference on aluminium alloys. Toyoashi, Japan, p 1531
Li X-M, Starink MJ (2001) Mater Sci Technol 17:1324
Gerlich A, Su P, North TH, Bendzsak GJ (2006) Proceedings on friction stir welding colloquium. University of Graz, Austria, p 65
ASM metals handbook, 8th edn. (1961)
Su P, Gerlich A, North TH, Bendzsak GJ (2006) Metall Trans A accepted 2006
Aluminum: the corrosion resistant automotive material (2001) Publication AT7, The Aluminum Association
Davis JR (1993) Aluminum and aluminum alloys. ASM Intl., Materials Park
Bowden FP, Ridler KEW (1936) Proc R Soc London, Ser A 154(883):640
Bowden FP, Thomas PH (1954) Proc R Soc London, Ser A 223(1152):29
Gerlich A, Su P, Bendzsak GJ, North TH (2005) In: Jata KV, Mahoney MW, Mishra RS (eds) Friction stir welding and processing III. TMS, p 249
Quinn TFJ, Winer WO (1985) Wear 102:67
Yamamoto M, Su P, Gerlich A, North TH (2007) SAE Technical Series, 2007-01-1700
Song M, Kovacevic R (2002) Trans SME 621
Colegrove P, Shercliff H (2003) Sci Tech Weld Joining 8(5):360
Lambrakos SG, Fonda RW, Milewski JO, Mitchell JE (2003) Sci Tech Weld Joining 8(5):385
Mishin OV, Godfrey A, Östensson L (2006) Metall Trans A 37A:489
Humphreys FJ (2001) J Mater Sci 36:3833
Gerlich A, Cingara GA, North TH (2006) Mater Sci Forum 519–521:1107
Mcqueen HJ, Jonas JJ (1975) Treatise on materials science technology, vol 6. Academic Press, New York, p 393
Mcqueen HJ, Hocket JE (1970) Metall Trans A 1:2997
Avramovic-Cingara G, Mcqueen HJ (1994) Aluminium 70(3):214
Avramovic-Cingara G, Perovic DD, Mcqueen HJ (1996) Metall Mater Trans 27A:3478
Cerri E, Evangelista E, Forcellese A, Mcqueen HJ (1995) Mater Sci Eng A197:181
Sheppard T (1990) In: Chen CQ, Starke EA (eds) 2nd international conference on aluminum alloys—their physical and mechanical properties. International Academic Publisher, p 744
Mcqueen HJ (2003) Metall Trans A 33A:345
Sheppard T (1987) In: Leoben-Wien (ed) Proceedings of 8th light metal congress (8 Internationale Leichmetalltagung). p 301
Evangelista E, Mcqueen HJ, Bonetti E (1983) Deformation of multi-phase and particle containing materials. Risø National Laboratory, Roskilde, p 243
Pettersen T, Holmedal B, Nes E (2003) Metall Trans A 34A:2737
van Geertruyden WH, Misiolek WZ, Wang PT (2006) Mater Sci Eng A 419:105
Hassan KhAA, Prangnell PB, Norman AF, Price DA, Williams SW (2003) Sci Technol Weld Joining 8:257
Yan Y, Lui B, Zhang C (1998) Proceedings of 6th international conference on aluminium alloys. Toyoashi, Japan, p 1135
Reiso O, Øverlie H-G, Ryum N (1990) Metall Trans 21A:1689
Whelan MJ (1969) Met Sci J 3:95
Acknowledgement
The authors wish to acknowledge financial support from the Natural Sciences and Engineering Research Council of Canada during this project.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gerlich, A., Yamamoto, M. & North, T.H. Local melting and tool slippage during friction stir spot welding of Al-alloys. J Mater Sci 43, 2–11 (2008). https://doi.org/10.1007/s10853-007-1791-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-007-1791-7