Skip to main content

Cutting characteristics of beard hair

Abstract

The cutting behaviour of beard hair has been investigated quantitatively and qualitatively. High speed cutting tests were conducted on beard hair samples using a purpose built cutting rig (provided by Gillette, UK) to determine the cutting forces. High speed digital video photography was used to record the cutting process. In parallel with these tests, low speed cutting tests were undertaken within a scanning electron microscope (SEM) to gain a better understanding of the cutting process. Results from the high speed cutting tests showed that the peak cutting stresses are influenced strongly by moisture (the cutting stress for ‘wet’ samples is reduced by about 30% as compared to dry samples) while the effects on the cutting stress of other variables (subject age, blade approach angle and sample ageing due to prolonged storage) appeared to be less noticeable. The angle of cut was affected by the distance of the initial contact point (between the hair and the blade) from the base of the hair with the line of cut shifting towards the hair axis with increasing distance from the base. Qualitative observations from video-recordings and still images taken during the cutting tests, conducted in-situ within the SEM as well as the high speed cutting rig, showed four main cutting mechanisms of hair, which are documented in this paper. The distance from the initial contact point to the base of the hair and the moisture level were the parameters which controlled the mechanism of failure. Qualitative observations of the sort reported here are a necessary pre-cursor to the development of finite element models to simulate a cutting operation.

This is a preview of subscription content, access via your institution.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19

References

  1. 1.

    Thozhur SM, Crocombe AD, Smith PA, Mullier M, Cowley K (2006) J Mat Sci 41(4):1109

    Article  CAS  Google Scholar 

  2. 2.

    Dawber RPR (1986) Bioeng Skin 2:1

    Google Scholar 

  3. 3.

    Dawber R (1996) Clin Dermatol 14:105

    Article  CAS  Google Scholar 

  4. 4.

    Jones LN (2001) Clin Dermatol 19:95

    Article  CAS  Google Scholar 

  5. 5.

    Swift JA (1991) Intl J Cosmet Sci 13:143

    Article  Google Scholar 

  6. 6.

    Swift JA (1997) AIM J EXS 78:149

    CAS  Google Scholar 

  7. 7.

    Watanabe H, Yahagi K. (1992) Jpn J Tribol 37(4):427

    Google Scholar 

  8. 8.

    Feughelman M (1997) Cosmet Sci Technol Ser 17:1

    CAS  Google Scholar 

  9. 9.

    Feughelman M (1982) J Soc Cosmet Chem 33:385

    CAS  Google Scholar 

  10. 10.

    Sakai M, Nagase S, Okada T, Satoh N, Tsujii K (2000) Bull Chem Soc Jpn 73:2169

    Article  CAS  Google Scholar 

  11. 11.

    Feughelman M (1964) Textile Res J 34:539

    Article  CAS  Google Scholar 

  12. 12.

    Feughelman M (1994) Textile Res J 64(4):236

    CAS  Google Scholar 

  13. 13.

    Deem D, Rieger MM (1976) J Soc Cosmet Chem 27:579

    Google Scholar 

  14. 14.

    Trusty PA (1994) PhD thesis (University of Surrey)

Download references

Acknowledgements

The authors would like to acknowledge the sponsorship offered by The Gillette Company to facilitate the research work discussed in this paper and the co-operation extended by the organisation through granting access to the high-speed cutting rig/video-recording apparatus.

Author information

Affiliations

Authors

Corresponding author

Correspondence to A. D. Crocombe.

Rights and permissions

Reprints and Permissions

About this article

Cite this article

Thozhur, S.M., Crocombe, A.D., Smith, P.A. et al. Cutting characteristics of beard hair. J Mater Sci 42, 8725–8737 (2007). https://doi.org/10.1007/s10853-006-1338-3

Download citation

Keywords

  • Hair Sample
  • Scalp Hair
  • Blade Angle
  • Cutting Test
  • Hair Surface