Abstract
Finite element (FE) simulations of visco-plastic indentation in Sn-37Pb eutectic solder alloy are performed to investigate the influence of loading rate on its creep characteristic. The resulting indentation load-displacement curves are rate-dependent and have varying creep penetration depths during the same hold time. Creep indentation hardness H, defined from the concept of “work of indentation”, varies with volume strain occurring during the creep hold time, which is a measure of creep strain rate \(\dot \varepsilon\)cr. Thus, creep stress sensitivity can be determined from the H versus \(\dot \varepsilon\)cr curve. This analysis can be verified by the good agreement between the derived value and the predefined value, and then be used to analyze the Berkovich indentation load-displacement curves of Sn-3.5Ag-0.75Cu lead-free solder. Such indentation tests and physical analysis provide a cheaper and more convenient method to determine the mechanical properties of the upcoming lead-free solder alloys.
Similar content being viewed by others
References
J. GLAZER, Intern. Mater. Rev. 40 (1995) 65.
M. ABTEW and G. SELVADURAY, Mater. Sci. Eng. Reports 27 (2000) 95.
K. SUGANUMA, Curr. Opin. Solid State Mater. Sci. 5 (2001) 55.
M. FUJIWARA and M. OTSUKA, Mater. Sci. Eng. A 319–321 (2001) 929.
C.-M. CHENG and Y.-T. CHENG, Appl. Phys. Lett. 71 (1997) 2623.
A. E. GIANNAKOPOULOS and S. SURESH, Scripta Mater. 40 (1999) 1191.
M. SAKAI, J. Mater. Res. 14 (1999) 3630.
K. ZENG and C.-H. CHIU, Acta Mater. 49 (2001) 3539.
P.-L. LARSSON, Int. J. Mech. Sci. 43 (2001) 895.
J. H. LAU (eds.), “Solder Joint Reliability: Theory and Application” (Von Nostrand Reinhold, New York, 1992).
W. J. PLUMBRIDGE, J. Mater. Sci. 31 (1996) 2501.
R. DARVEAUX and K. BANERJI, IEEE Trans. CHMT. 15 (1992) 1013.
X.-Q. SHI, Z.-P. WANG, et al., ASME J. Electron. Packag. 124 (2002) 85.
Y. WEI, C.-L. CHOW, H.-E. FANG and M.-K. NEILSEN, ibid. 123 (2001) 278.
A. DESHPANDE, G. SUBBARAYAN and D. ROSE, ibid. 122 (2002) 6.
W. C. OLIVER and G. M. PHARR, J. Mater. Res. 7 (1992) 1564.
T.-A. VENKATESH, K.-J. VAN VLIET, A.-E. GIANNAKOPOULOS and S. SURESH, Scripta Mater. 42 (2000) 833.
N.-A. STILWELL and D. TABOR, Proc. Phys. Soc. 78 (1961) 169.
J.-R. TUCK, A.-M. KORSUNSKY, S. J. BULL and R. I. DAVIDSON, Surf. Coat. Technol. 137 (2001) 217.
K.-L. JOHNSON, J. Mech. Phys. Solids 18 (1970) 115.
D. TABOR, “Hardness of Metals,” (Oxford University Press, London, 1951).
M. MATA, M. ANGLADA and J. ALCALÁ, J. Mater. Res. 17 (2002) 964.
B. P. RICHARDS et al., “An Analysis of the Current Status of Lsead-free Soldering,” NPL and ITRI Report (1999).
S. WIESE, E. MEUSEL and K.-J. WOLTER, 53rd ECTC 2003, p. 197.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, FJ., Ma, X. & Qian, YY. Rate-dependent indentation behavior of solder alloys. J Mater Sci 40, 1923–1928 (2005). https://doi.org/10.1007/s10853-005-1212-8
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/s10853-005-1212-8