Sol-gel synthesis by the eutectic composition method was conducted in the ternary oxide system MgO–Al2O3–Y2O3, used as a sintering additive for silicon oxide based ceramics. Alaboratory method of preparing additives is proposed and the influence of the synthesis temperature on the powder properties is determined.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
A. P. Garshin, Ceramics for Machine Engineering [in Russian], Nauch-tekhizdat, Moscow (2003).
S. N. Perevislov, I. B. Panteleev, S. V. Vikhman, and M. V. Tomkovich, “The effect of preliminary methods of synthesis of complex oxides on the compactability of liquid phase sintered silicon carbide material,” Ogneup. Tekh. Keram., No. 7 – 8, 30 – 35 (2015).
S. V. Zhitnyuk, Ceramics Based on Silicon Carbide, Modified by Eutectic Additive. Author’s Abstract of Candidate’s Thesis [in Russian], Mendeleev Russian University of Chemical Technology, Moscow (2015).
Z. H. Huang, D. C. Jia, and Y. G. Liu, “A new sintering additive for silicon carbide ceramic,” Ceram. Int., 29(1), 13 – 17 (2003).
M. L. Vaganova, D. V. Grashchenkov, and S. S. Solntsev, “Modifying components to enhance the performance of high-temperature composite materials for construction,” Ogneup. Tekh. Keram., No. 6, 12 – 18 (2013).
N. N. Bekov and V. I. Dosovitskii, “Unconventional methods of synthesizing ferroelectrics based on lead-zirconate-titanate,” Khim. Prom-st’, No. 1, 27 – 29 (2016).
N. A. Makarov, M. A. Vartanyan, D. U. Zhukov, D. O. Lemeshev, and E. E. Nazarov, “Thermodynamic analysis as a method for choosing dopants in silicon carbide ceramics production,” Steklo Keram., No. 12, 18 – 224 (2016); N. A. Makarov, M. A. Vartanyan, D. U. Zhukov, D. O. Lemeshev, and E. E. Nazarov, “Thermodynamic analysis as a method for choosing dopants in silicon carbide ceramics production,” Glass Ceram., 73(11 – 12), 450 – 453 (2016).
N. A. Makarov, M. A. Vartanian, O. V. Yarovaya, and E. E. Nazarov, “Study of the wetting of silicon carbide by oxide melts,” Tekh. Tekhnol. Silikatov, No. 4, 7 – 17 (2016).
S. N. Perevislov, V. D. Chupov, S. S. Ordan’yan, M. V. Tomkovich, “Fabrication of high-density silicon carbide materials by liquid phase sintering in the system of components SiC–Al2O3–Y2O3–MgO,” Ogneup. Tekh. Keram.,No. 4 – 5, 26 – 32 (2011).
P. P. Faikov, Synthesis and Sinterability of Powders in the System MgO–Al 2 O 3 System Obtained by the Sol-Gel Method, Author’s Abstract of Candidate’s Thesis [in Russian], Mendeleev Russian University of Chemical Technology, Moscow (2007).
This work was performed with the financial support from the Ministry of Education and Science of the Russian Federation as part of the base part of state contract No. 10.6309.2017/BCh.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Steklo i Keramika, No. 9, pp. 25 – 27, September, 2017.
Rights and permissions
About this article
Cite this article
Mararakin, M.D., Vartanyan, M.A., Makarov, N.A. et al. Sol-Gel Synthesis by Means Of Eutectic Additives for Silicon Carbide Based Ceramic. Glass Ceram 74, 326–328 (2018). https://doi.org/10.1007/s10717-018-9987-7
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10717-018-9987-7