Skip to main content

Advertisement

SpringerLink
Log in

A Theoretical Model to Understand Some Aspects of Firebrand Pile Burning

  • Published:
Fire Technology Aims and scope Submit manuscript

Abstract

Firebrand piles are known to ignite combustible infrastructure resulting in significant damage; however, the parameters that impact the heat transfer from firebrand piles to a combustible surface are not well understood. Heat transfer from a firebrand pile is directly related to the local firebrand temperatures which can vary significantly due to changes in the burning behavior. A two-phase flow analytical model was developed that includes time varying firebrand diameter, reradiation effects between firebrands, gas temperature and species evolution, and pile porosity effects. The analytical model was used to quantify the temperature of cylindrical firebrands and explore the effects of changing firebrand diameter, firebrand aspect ratio (pile porosity), gas velocity, and local oxygen mass fraction. All of these parameters were found to impact firebrand temperatures. Firebrand pile porosity has a significant impact on the velocity within the pile, with a decrease in pile porosity resulting in lower velocities and lower firebrand temperatures. The modeling results were used to explain the trends in heat transfer measured for firebrand piles on a horizontal plate.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18

Similar content being viewed by others

References

  1. Manzello SL, Suzuki S, Gollner MJ, Fernandez-Pello AC (2020) Role of firebrand combustion in large outdoor fire spread. Prog Energy Combust Sci 76:100801

    Article  Google Scholar 

  2. Caton SE, Hakes RSP, Gorham DJ, Zhou A, Gollner MJ (2017) Review of pathways for building fire spread in the wildland urban interface part I: exposure conditions. Fire Technol 53(2):429–473

    Article  Google Scholar 

  3. Dowling VP (1994) Ignition of timber bridges in bushfires. Fire Saf J 22(2):145–168

    Article  Google Scholar 

  4. Manzello SL, Cleary TG, Shields JR, Maranghides A, Mell W, Yang JC (2008) Experimental investigation of firebrands: generation and ignition of fuel beds. Fire Saf J 43(3):226–233

    Article  Google Scholar 

  5. Manzello SL, Park SH, Cleary TG (2009) Investigation on the ability of glowing firebrands deposited within crevices to ignite common building materials. Fire Saf J 44(6):894–900

    Article  Google Scholar 

  6. Hakes RSP, Salehizadeh H, Weston-dawkes MJ, Gollner MJ (2019) Thermal characterization of firebrand piles. Fire Saf J 104:34–42

    Article  Google Scholar 

  7. Manzello SL, Suzuki S (2014) Exposing decking assemblies to continuous wind-driven firebrand showers. Fire Saf Sci 11:1339–1352

    Article  Google Scholar 

  8. Wessies SS, Chang MK, Marr KC, Ezekoye OA (2019) Experimental and analytical characterization of firebrand ignition of home insulation materials. Fire Technol 55(3):1027–1056

    Article  Google Scholar 

  9. Manzello SL (2014) Enabling the investigation of structure vulnerabilities to wind-driven firebrand showers in wildland-urban interface (WUI) fires. Fire Saf Sci 11:83–96

    Article  Google Scholar 

  10. Manzello SL et al (2008) On the development and characterization of a firebrand generator. Fire Saf J 43:258–268

    Article  Google Scholar 

  11. Manzello SL, Suzuki S (2012) The new and improved NIST Dragon ’ s LAIR (Lofting and Ignition Research) facility. Fire Mater 1:623–635

    Article  Google Scholar 

  12. Suzuki S, Manzello SL (2019) Investigating effect of wind speeds on structural firebrand generation in laboratory scale experiments. Int J Heat Mass Transf 130:135–140

    Article  Google Scholar 

  13. Manzello SL, Suzuki S, Hayashi Y (2012) Exposing siding treatments, walls fitted with eaves, and glazing assemblies to firebrand showers. Fire Saf J 50:25–34

    Article  Google Scholar 

  14. Suzuki S, Johnsson E, Maranghides A, Manzello SL (2016) Ignition of wood fencing assemblies exposed to continuous wind-driven firebrand showers. Fire Technol 52(4):1051–1067

    Article  Google Scholar 

  15. Tao Z, Bathras B, Kwon B, Biallas B, Gollner MJ, Yang R (2020) Effect of firebrand size and geometry on heating from a smoldering pile under wind. Fire Saf J 1:103031

    Google Scholar 

  16. Bearinger E, Lattimer B, Hodges J, Rippe C, Kapahi A (2021) Statistical assessment of parameters affecting firebrand pile heat transfer to surfaces. Front Mech Eng 7:62

    Article  Google Scholar 

  17. Koo E, Pagni PJ, Weise DR, Woycheese JP (2010) Firebrands and spotting ignition in large-scale fires. Int J Wildl Fire 19(7):818–843

    Article  Google Scholar 

  18. Turns S (2000) An introduction to combustion: concepts and applications, 2nd edn. McGraw Hill, London

    Google Scholar 

  19. Baum HR, Atreya A (2014) A model for combustion of firebrands of various shapes. Fire Saf Sci 11:1353–1367

    Article  Google Scholar 

  20. Chaos M, Khan MM, Dorofeev SB (2013) Pyrolysis of corrugated cardboard in inert and oxidative environments. Proc Combust Inst 34(2):2583–2590

    Article  Google Scholar 

  21. Anca-Couce A, Zobel N, Berger A, Behrendt F (2012) Smouldering of pine wood: kinetics and reaction heats. Combust Flame 159(4):1708–1719

    Article  Google Scholar 

  22. Hurt RH, Mitchell RE (1992) On the combustion kinetics of heterogeneous char particle populations. In: Twenty-fourth symposium on combustion, pp 1233–1241

  23. Weng WG, Hasemi Y, Fan WC (2006) Predicting the pyrolysis of wood considering char oxidation under different ambient oxygen concentrations. Combust Flame 145(4):723–729

    Article  Google Scholar 

  24. Lattimer BY, Bearinger E, Wong S, Hodges JL (2022) Evaluation of models and important parameters for firebrand burning. Combust Flame 235:111619

    Article  Google Scholar 

  25. Monson CR, Germane GJ, Blackham AU, DouglasSmoot L (1995) Char oxidation at elevated pressures. Combust Flame 100(4):669–683

    Article  Google Scholar 

  26. Zhou L (2018) Fundamentals of combustion theory. Elsevier, Amsterdam, pp 15–70

    Google Scholar 

  27. Rogers FE, Ohlemiller TJ (1980) Cellulosic insulation material I. Overall degradation kinetics and reaction heats. Combust Sci Technol 24(3–4):129–137

    Article  Google Scholar 

  28. Kashiwagi T, Nambu H (1992) Global kinetic constants for thermal oxidative degradation of a cellulosic paper. Combust Flame 88(3–4):345–368

    Article  Google Scholar 

  29. Incopera F, DeWitt D (1990) Fundamentals of heat and mass transfer, 3rd edn. Wiley, London

    Google Scholar 

  30. Barr BW, Ezekoye OA (2013) Thermo-mechanical modeling of firebrand breakage on a fractal tree. Proc Combust Inst 34(2):2649–2656

    Article  Google Scholar 

  31. Zou RP, Yu AB (1996) Evaluation of the packing characteristics of mono-sized non-spherical particles. Powder Technol 88:71–79

    Article  Google Scholar 

  32. Zhang C, Gao J, Zeng L, Xia Y, Xie W, Ye W (2020) Experimental analysis of the resistance of packed beds based on the morphology of cylinder. Powder Technol 369:238–247

    Article  Google Scholar 

  33. Cholewa N, Summers PT, Feih S, Mouritz AP, Lattimer BY, Case SW (2016) A technique for coupled thermomechanical response measurement using infrared thermography and digital image correlation (TDIC). Exp Mech 56:145–164

    Article  Google Scholar 

  34. Rippe CM, Lattimer BY (2015) Full-field surface heat flux measurement using non-intrusive infrared thermography. Fire Saf J 78:238–250

    Article  Google Scholar 

  35. Bearinger ED, Hodges JL, Yang F, Rippe CM, Lattimer BY (2021) Localized heat transfer from firebrands to surfaces. Fire Saf J 120:1–10

    Article  Google Scholar 

  36. Bearinger E, Lattimer B, Hodges J, Rippe C (2020) Measuring heat transfer from firebrands to surfaces. In: Proceeding of ASME 2020 heat transfer summer conference HT2020-9165, July 13–15, pp 1–9

  37. Howell JR, Menguc MP (2011) A catalog of radiation heat transfer configuration factors. J Quant Spectros Radiat Transf 112(5):910–912

    Article  Google Scholar 

  38. Urban JL, Fernandez-pello AC, Vicariotto M, Dunn-Rankin D (2019) Temperature measurement of glowing embers with color pyrometry. Fire Technol 55(3):1013–1026

    Article  Google Scholar 

  39. Manzello SL, Maranghides A (2007) Measurement of firebrand production and heat release rate (HRR) from burning Korean pine trees. Fire Saf Sci 7:108–116

    Google Scholar 

Download references

Acknowledgements

This research was funded by the National Institute of Standards and Technology (NIST) under contract NIST Grant No. 70NANB19H052. Brian Lattimer has an ownership/equity interest in Jensen Hughes.

Author information

Authors and Affiliations

  1. Mechanical Engineering Department, Virginia Tech, Blacksburg, VA, 24060, USA

    Brian Y. Lattimer & Steven Wong

  2. Jensen Hughes, Blacksburg, VA, 24060, USA

    Jonathan Hodges

  3. Mechanical Engineering, Virginia Tech, 635 Prices Fork Road, Goodwin Hall Rm 413D, Blacksburg, VA, 24060, USA

    Brian Y. Lattimer

Authors
  1. Brian Y. Lattimer
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Steven Wong
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jonathan Hodges
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Brian Y. Lattimer.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lattimer, B.Y., Wong, S. & Hodges, J. A Theoretical Model to Understand Some Aspects of Firebrand Pile Burning. Fire Technol 58, 3353–3384 (2022). https://doi.org/10.1007/s10694-022-01303-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10694-022-01303-5

Keywords

Search

Navigation