Skip to main content
SpringerLink
Log in

Determining the Geometric Parameters of a Sheared Layer in Drilling of Nonferrous Metals and Alloys with the Use of Axial Vibrations

  • Published:
Chemical and Petroleum Engineering Aims and scope

The problem of determining the kinematic parameters of a vibrodrilling device and the geometric elements of a sheared layer produced in the course of treating nonferrous metals and alloys by drilling with the use of axial vibrations is considered. Relationships between the dimensions of an element of a chip and the frequency of the axial vibrations are found.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  1. A. V. Maslennikov, S. A. Chevychelov, V. V. Sidorova, et al., “Use of vibration cutting to control chip formation,” Izv. Yugo-Zapad. Gos. Univ. Ser. Tekhn. Tekhnol., No. 2, Pt. 1, 117–120 (2012).

  2. E. A. Kopeykin, Increasing the Strength of a Tool for Deep Vibration Drilling of Holes of Low Diameter: Dissert. Cand. Techn. Sci.: 05.03.01, 05.02.02, Moscow (2003).

  3. V. V. Sidorova, M. S. Razumov, and P. A. Ponkratov, Patent 147317 RF, IPC GB23B35/00, “A device for vibration drilling,” Claimant and Patentee Southwest State University, No. 2014120738/02, subm 05.22.2014, publ. 11.10.2014, Byull., No. 21.

  4. V. V. Sidorova and M. S. Razumov, “A device for vibration drilling,” Fund. Prikl. Probl. Tekhn. Tekhnol., No. 4 (306), 51–54 (2014).

  5. V. V. Sidorova and M. S. Razumov, “A study of the influence of an axial load on a twist drill with cylindrical tool stem,” Innovations in Science, Processes, and Technologies: Proc. All-Russ. Sci. Techn. Conf., Izhevsk State Techn. Univ., Izhevsk (2014), pp. 242–243.

Download references

Author information

Authors and Affiliations

  1. Southwest State University, Kursk, Russia

    S. G. Emel’yanov, V. V. Sidorova, V. V. Ponomarev & M. S. Razumov

Authors
  1. S. G. Emel’yanov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. V. V. Sidorova
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. V. Ponomarev
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. M. S. Razumov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to S. G. Emel’yanov.

Additional information

Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 11, pp. 45–47, November, 2016.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Emel’yanov, S.G., Sidorova, V.V., Ponomarev, V.V. et al. Determining the Geometric Parameters of a Sheared Layer in Drilling of Nonferrous Metals and Alloys with the Use of Axial Vibrations. Chem Petrol Eng 52, 796–800 (2017). https://doi.org/10.1007/s10556-017-0273-2

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10556-017-0273-2

Keywords

Search

Navigation