Abstract
A procedure is presented for the approximate mathematical description and analyses of regime parameters for examples of the thermal-diffusion treatment of strip materials and inner-tube valves. The dependence of economic outlays for a corded-rubber fabric on the number of drums contained in the unit is indicated.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
M. B. Generalov, Basic Processes and Equipment in the Production of Industrial Explosives [in Russian], IKTs Akademkniga, Moscow (2003).
V. I. Konovalov, N. Ts. Gatapova, and E. N. Tugolukov, “Feasibility of using cyclical thermal and interrelated thermal-diffusion processes in chemical and other productions,” Vestn. Tambov. Gos. Tekh. Univ., 1, Nos.3–4, 273–288 (1995).
E. E. Kol’man-Ivanov and Yu. I. Gusev, Automated Machines and Automated Lines for Chemical Production [in Russian], MGUIE, Moscow (2003).
L. N. Koshkin, Rotary and Rotary-Conveyer Lines [in Russian], 3rd edition, Mashinostroenie, Moscow (1991).
N. M. Varenykh, A. N. Verigin, V. G. Dzhangiryan, and A. S. Dudyrev, Rotary-Conveyer Lines for the Production of Energy-Intensive Articles [in Russian], Izd. Mendeleev, St. Petersburg (2003).
N. Ts. Gatapova, “Kinetics and optimization of cyclic thermal processes during vulcanization of rubber blanks,” Dissertation for Candidate of Technical Sciences, Tambovskii Institut Khimicheskogo Mashinostroeniya, Tambov (1992).
E. N. Tugolukov, “Kinetics of the drying and cooling of glue-smeared rubber blanks,” Dissertation for Candidate of Technical Sciences, Tambovskii Institut Khimicheskogo Mashinostroeniya, Tambov (1986).
V. I. Konovalov, E. N. Tugolukv, and N. Ts. Gatapova, “On the potential for use of exact, interval, and approximate analytical methods in problems of heat-and-mass transfer in solids,” Vestn. Tambov. Gos. Tekh. Univ., 1, Nos.1–2, 75–90 (1995).
A. N. Koliukh, “Kinetics of the cooling, heating, and drying of rolled-sheet materials on contact drums,” Dissertation for Candidate of Technical Sciences, Tambovskii Gosudarstvennyi Tekhnicheskii Universitet, Tambov (2001).
E. N. Tugolukov, “Mathematical modeling of thermally loaded processes and equipment of multiple-assortment chemical productions,” Dissertation for Candidate of Technical Sciences, Tambovskii Gosudarstvennyi Tekhnicheskii Universitet, Tambov (2004).
V. I. Konovalov, N. Z. Gatapova, E. N. Tugolukov, and G. L. Nemtchenko, “Cyclic heating processes for the modern equipment for rubber and plastic articles production,” in: Eleventh International Congress CHISA’93, Preprint G8.25, Prague (1993).
V. I. Konovalov, A. G. Posternak, E. N. Tugolukov, L. V. Prudnik, and V. N. Zatona, “Problems of all-round optimizing of cooling and shrinking processes for extruded rubber and plastic products,” in: Fourth World Congress DECHEMA’91 “Strategies 2000,” Preprint IV, Session 2.3-12, Karlsruhe (1991).
F. Kreith, “Convection heat transfer in rotating systems,” Advances In Heat Transfer, Vol. 5, Academic Press, New York (1968).
B. S. Petukhov, Heat Exchange and Resistance During Laminar Fluid Flow in Pipes [in Russian], Energiya, Moscow (1967).
Author information
Authors and Affiliations
Additional information
__________
Translated from Khimicheskoe i Neftegazovoe Mashinostroenie, No. 5, pp. 3–7, May, 2005.
Rights and permissions
About this article
Cite this article
Gatapova, N.T., Konovalov, V.I. & Tugolukov, E.N. Analysis and Optimization of Thermal Conditions for the Treatment of Articles on Continuous, Rotary-Conveyer, and Rotary Production Lines. Chem Petrol Eng 41, 231–239 (2005). https://doi.org/10.1007/s10556-005-0095-5
Issue Date:
DOI: https://doi.org/10.1007/s10556-005-0095-5