Abstract
In this research, two simple fabrication methods to fabricate orderly nanostructured PLGA scaffolds using anodic aluminum oxide (AAO) template were conducted. In the vacuum air-extraction approach, the PLGA solution was cast on an AAO template first. The vacuum air-extraction process was then applied to suck the semi-congealed PLGA into the nanopores of the AAO template to form a bamboo sprouts array of PLGA. The surface roughness of the nanostructured scaffolds, ranging from 20 nm to 76 nm, can be controlled by the sucking time of the vacuum air-extraction process. In the replica molding approach, the PLGA solution was cast on the orderly scraggy barrier-layer surface of an AAO membrane to fabricate a PLGA scaffold of concave nanostructure. Cell culture experiments using the bovine endothelial cells (BEC) demonstrated that the nanostructured PLGA membrane can increase the cell growing rate, especially for the bamboo sprouts array scaffolds with smaller surface roughness.
Similar content being viewed by others
References
J. Anderson, M. Shive, Adv. Drug Deliv. Rev. 28(1), 5–24 (1997). doi:10.1016/S0169-409X(97)00048-3
M.J. Dalby, D. Giannaras, M.O. Riehle, N. Gadegaard, S. Affrossman, A.S.G. Curtis, Biomaterials 25, 77–83 (2004). doi:10.1016/S0142-9612(03)00475-7
E.J. Frazza, E.E. Schmitt, J. Biomed. Mater. Res. 5, 43–58 (1971). doi:10.1002/jbm.820050207
A. Goepferich, Biomaterials 17, 103–114 (1996). doi:10.1016/0142-9612(96)85755-3
A.L. Luis, J.M. Rodrigues, S. Amado, A.P. Veloso, P.A. Armada-Da-Silva, S. Raimondo, F. Fregnan, A.J. Ferreira, M.A. Lopes, J.D. Santos, S. Geuna, A.S. Varejao, A.C. Mauricio, Microsurgery 27, 125–137 (2007). doi:10.1002/micr.20317
D.C. Miller, K.M. Haberstroh, T.J. Webster, J. Biomed. Mater. Res. 74A, 678–684 (2006)
B.M. Min, Y. You, J.M. Kim, S.J. Lee, W.H. Park, Carbohydr. Polym. 57, 285–292 (2004). doi:10.1016/j.carbpol.2004.05.007
G. Mittal, D.K. Sahana, V. Bhardwaj, M.N. Kumar, J. Control. Release 119(1), 77–85 (2007). doi:10.1016/j.jconrel.2007.01.016
G.E. Park, K. Park, T.J. Webster, Biomaterials 26(16), 3075–3082 (2005). doi:10.1016/j.biomaterials.2004.08.005
W.H. Ryu, M. Vyakarnam, R.S. Gerco, F.B. Prinz, R.J. Fasching, Biomed. Microdevices 9(6), 845–853 (2007). doi:10.1007/s10544-007-9097-8
J.K. Savaiano, T.J. Webster, Biomaterials 25((7), 1205–1213 (2004). doi:10.1016/j.biomaterials.2003.08.012
K. Sonaje, J.L. Italia, G. Sharma, V. Bhardwaj, K. Tikoo, M.N. Kumar, Pharm. Res. 24(5), 899–908 (2007). doi:10.1007/s11095-006-9207-y
G.J. Wang, C.C. Hsueh, S.H. Hsu, H.S. Hung, J. Micromech. Microeng 17, 2000–2005 (2007). doi:10.1088/0960-1317/17/10/011
T.J. Webster, Z. Tong, J. Liu, M.K. Banks, Nanotechnology 16, S449–S457 (2005). doi:10.1088/0957-4484/16/7/021
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, GJ., Lin, YC., Li, CW. et al. Fabrication of orderly nanostructured PLGA scaffolds using anodic aluminum oxide templates. Biomed Microdevices 11, 843–850 (2009). https://doi.org/10.1007/s10544-009-9301-0
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10544-009-9301-0