Abstract
Concrete block infill walls, due to their high strength and stiffness, can significantly influence the seismic behavior of the frames. The infill walls can increase the overall lateral frame strength and can also induce local failures in the surrounding frames. In general, if local failure can be avoided, the presence of the infill walls can provide additional reserved strength that can be beneficial to the frames. For this reason, a new RC frame with infill walls could be designed as a bare frame without considering the increase in strength, but measures must be taken to prevent local failures due to the infill wall-frame interaction. However, this infill wall-frame interaction is very complex, and clear design strategies to prevent local failures are not normally given in design codes. For this reason, two full-scale intermediate RC moment-resisting frame specimens with infill concrete block walls were tested under a horizontal cyclic load to study the infill wall-frame interaction. Finite element analysis was carried out to evaluate the response particularly on the infill-frame interactions. Based on the results, a design strategy to eliminate local failure in the surrounding frame is suggested. The proposed method is based on local plastic mechanism analysis of the column considering the variation in the column shear demand and column shear capacity at different states of the response as the frame deforms. The shear demand depends on the magnitude and direction of the bearing force from the infill wall. The column is considered as a captive or slender column depending on the restraint from the infill wall, thereby affecting the shear capacity of the column. The proposed approach can be readily applied without radically changing common design practices and design codes.
Similar content being viewed by others
References
Al-Chaar G, Issa M, Sweeney S (2002) Behavior of masonry-infilled nonductile reinforced concrete frames. J Struct Eng 128(8):1055–1063
Alwashali H, Sen D, Jin K, Maeda M (2019) Experimental investigation of influences of several parameters on seismic capacity of masonry infilled reinforced concrete frame. Eng Struct 189:11–24. https://doi.org/10.1016/j.engstruct.2019.03.020
American Concrete Institute (ACI) (2005) Building code requirements for structural concrete and commentary. ACI318/318R, Farmington Hills, Michigan, USA
American Concrete Institute (ACI) (2014) Building code requirements for structural concrete and commentary. ACI318/318R, Farmington Hills, Michigan, USA
American Society of Civil Engineers (ASCE) (2013) Seismic evaluation and retrofit of existing buildings. ASCE/SEI41, Reston, Virginia, USA
Asteris PG (2003) Lateral stiffness of brick masonry infilled plane frames. J Struct Eng 129(8):1071–1079. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:8(1071)
Asteris PG, Cotsovos DM, Chrysostomou CZ, Mohebkhah A, Al-Chaar GK (2013) Mathematical micromodeling of infilled frames: state of the art. Eng Struct 56:1905–1921
Asteris PG, Repapis CC, Cavaleri L, Sarhosis V, Athanasopoulou A (2015) On the fundamental period of infilled RC frame buildings. Struct Eng Mech 54(6):1175–1200
Basha SH, Kaushik HB (2016) Behavior and failure mechanisms of masonry-infilled RC frames (in low-rise buildings) subject to lateral loading. Eng Struct 111:233–245. https://doi.org/10.1016/j.engstruct.2015.12.034
Basha SH, Kaushik HB (2019a) A novel macro model for prediction of shear failure in columns of masonry infilled RC frames under earthquake loading. Bull Earthq Eng 17(4):2219–2244. https://doi.org/10.1007/s10518-018-00537-5
Basha SH, Kaushik HB (2019b) Investigation on improving the shear behavior of columns in masonry infilled RC frames under lateral loads. Bull Earthq Eng 17(7):3995–4026. https://doi.org/10.1007/s10518-019-00622-3
Basili M, Marcari G, Vestroni F (2016) Nonlinear analysis of masonry panel strengthened with textile reinforced mortar. Eng Struct 113:245–258. https://doi.org/10.1016/j.engstruct.2015.12.021
Bertero V, Brokken S (1983) Infills in seismic resistant building. J Struct Eng 109(6):1337–1361
Blasi G, Perrone D, Aiello MA (2018) Fragility functions and floor spectra of RC masonry infilled frames: influence of mechanical properties of masonry infills. Bull Earthq Eng 16(12):6105–6130. https://doi.org/10.1007/s10518-018-0435-4
Burton H, Deierlein G (2014) Simulation of seismic collapse in nonductile reinforced concrete frame buildings with masonry infills. J Struct Eng 149(8):A4014016. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000921
Cavaleri L, Trapani F (2015) Prediction of the additional shear action on frame members due to infills. Bull Earthq Eng 13(5):1425–1454. https://doi.org/10.1007/s10518-014-9668-z
CEB-FIP (2010) Fib model code for concrete structures 2010. Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim, Germany
Celarec D, Ricci P, Dolšek M (2012) The sensitivity of seismic response parameters to the uncertain modelling variables of masonry-infilled reinforced concrete frames. Eng Struct 35:165–177. https://doi.org/10.1016/j.engstruct.2011.11.007
Crisafulli F (1997) Seismic behaviour of reinforced concrete structures with masonry infills. Dissertation, University of Canterbury, Christchurch, New Zealand
D’Ayala D, Worth J, Riddle O (2009) Realistic shear capacity assessment of infill frames: Comparison of two numerical procedures. Eng Struct 31(8):1745–1761. https://doi.org/10.1016/j.engstruct.2009.02.044
DIANA FEA BV (2019) DIANA Finite element analysis user manual. Delftechpark 19a, 2628 XJ, Delft, The Netherlands
European Committee for Standardization (CEN) (2004) Design of structures for earthquake resistance–part 1: general rules, seismic actions and rules for buildings. BS EN 1998-1. Eurocode 8, Brussels, Belgium
Fardis MN, Panagiotakos TB (1997) Seismic design and response of bare and masonry-infilled reinforced concrete buildings. Part II: infilled structures. J Earthq Eng 1(3):475–503
Fardis MN, Bousias SN, Franchioni G, Panagiotakos TB (1999) Seismic response and design of RC structures with plan-eccentric masonry infills. Earthq Eng Struct Dyn 28:173–191
Favvata MJ, Naoum MC, Karayannis CG (2013) Limit states of RC structures with first floor irregularities. Struct Eng Mech 47(6):791–818. https://doi.org/10.12989/SEM.2013.47.6.791
Fiorato AE, Sozen MA, Gamble WL (1970) An investigation on the interaction of reinforced concrete frames with masonry filler walls. Report UILU-ENG 70-100, University of Illinois, Urbana Champaign
Fiore A, Netti A, Monaco P (2012) The influence of masonry infill on the seismic behaviour of RC frame buildings. Eng Struct 44:133–145
Fiore A, Spagnoletti G, Greco R (2016) On the prediction of shear brittle collapse mechanisms due to the infill-frame interaction in RC buildings under pushover analysis. Eng Struct 121:147–159. https://doi.org/10.1016/j.engstruct.2016.04.044
Hashmi AK (2016) Seismic evaluation and preliminary design of regular setback masonry infilled open ground storey RC frame. J Inst Eng (India) 97(2):121–131. https://doi.org/10.1007/s40030-016-0151-5
Huang H, Burton HV (2020) A database of test results from steel and reinforced concrete infilled frame experiments. Earthq Spectra. https://doi.org/10.1177/8755293019899950
Hwang SJ, Lee HJ (2002) Strength prediction for discontinuity regions by softened strut-and-tie model. J Struct Eng 128(12):1519–1526
Kaushik HB, Rai DC, Jain SK (2006) Code approaches to seismic design of masonry-infilled reinforce concrete frames: a state-of-art review. Earthq Spectra 22(4):961–983
Kostinakis K, Athanatopoulou A (2019) Effects of in-plan irregularities caused by masonry infills on the seismic behavior of R/C buildings. Soil Dyn Earthq Eng. https://doi.org/10.1016/j.soildyn.2019.03.012
Koutromanos I, Stavridis A, Shing PB, Willam K (2011) Numerical modeling of masonry-infilled RC frames subjected to seismic loads. Comput Struct 89(11):1026–1037
Leeanansaksiri A, Panyakapo P, Ruangrassamee A (2018) Seismic capacity of masonry infilled RC frame strengthening with expanded metal ferrocement. Eng Struct 150:110–127. https://doi.org/10.1016/j.engstruct.2017.12.034
Li YA, Hwang SJ (2017) Prediction of lateral load displacement curves for reinforce concrete short columns failed in shear. J Struct Eng 143(2):04016164
Lourenco PB (1996) Computational strategies for masonry structures. Dissertation, Delft University of Technology, Delft, Netherlands
Lourenco PB (2009) Recent advances in Masonry modelling: micromodelling and homogenisation. Multiscale Model Solid Mech 3:251–294
Lourenco PB, Rots JG (1997) Multisurface interface model for analysis of masonry structures. J Eng Mech ASCE 123(7):660–668
Luca FD, Morciao E, Perrone D, Aiello MA (2018) MID1.0 Masonry infilled RC frame experimental database. In: Proceedings of Italian concrete days 2016 10:147–160. https://doi.org/10.1007/978-3-319-78936-1_11
Sanada, Maidiawati Y (2017) R/C frame–infill interaction model and its application to Indonesian buildings. Earthq Eng Struct Dyn 46(2):221–241. https://doi.org/10.1002/eqe.2787
Mainstone RJ (1971) On the stiffness and strength of infilled frames. Proc Inst Civ Eng, Supplement IV, pp 57–90
Medeiros P, Vasconcelos G, Lourenço PB, Gouveia J (2013) Numerical modeling of non-confined and confined masonry walls. Constr Build Mater 41:968–976. https://doi.org/10.1016/j.conbuildmat.2012.07.013
Mehrabi AB, Shing PB (1997) Finite element modeling of masonry-infilled RC frames. J Struct Eng 123(5):604–613
Mehrabi AB, Shing PB, Schuller MP, Noland JL (1996) Experimental evaluation of masonry-infilled RC frames. J Struct Eng 122(3):228–237
Milanesi RR, Morandi P, Magenes G (2018) Local effects on RC frames induced by AAC masonry infills through FEM simulation of in-plane test. Bull Earthq Eng 16(9):4053–4080. https://doi.org/10.1007/s10518-018-0353-5
Moghaddam HA, Dowling PJ (1988) Earthquake resistant design of brick infilled frames. In: Proceeding of the eighth international brick and block masonry conference, pp 774–784
Moretti M, Tassios TP (2007) Behavior and ductility of reinforced concrete short columns using global truss model. Eng Struct 29(8):2018–2029
Nagare KP, Bahaskar G, Nair V (2015) Seismic response of RC frame building with first soft storey. Int Res J Eng Technol 2(4):1762–1779
New Zealand Standard (NZS) (2006) Concrete structures standard. NZS3101.1/3101.2, Wellington, New Zealand
Niyompanitpattana S, Warnitchai P (2017) Effect of masonry infill walls with openings on seismic behavior of long-span GLD RC frames. Mag Concr Res 69(21):1082–1102
Oliveira DV, Lourenco PB (2004) Implementation and validation of a constitutive model for the cyclic behavior of interface elements. Comput Struct 82(17):1451–1461. https://doi.org/10.1016/j.compstruc.2004.03.041
Papia M, Cavaleri L, Fossetti M (2003) Infilled frames: developments in the evaluation of the stiffening effect of infills. Struct Eng Mech 16(6):675–693
Paulay T, Priestlay M (1992) Seismic design of reinforced concrete and masonry buildings, vol 744. Wiley, Hoboken. https://doi.org/10.1002/9780470172841
Saneinejad A, Hobbs B (1995) Inelastic design of infilled frames. J Struct Eng 121:634–650
Sattar S (2013) Influence of masonry infill walls and other buildings characteristics on seismic collapse of concrete frame buildings. Dissertation, University of Colorado, Colorado, USA
Sattar S, Liel AB (2016) Seismic performance of nonductile reinforced concrete frames with masonry infill walls I: development of a strut model enhanced by finite element models. Earthq Spectra 32(2):795–818. https://doi.org/10.1193/90914EQS139M
Schwarz S, Hanaor A, Yankelevsky DZ (2015) Experimental response of reinforced concrete frames with AAC masonry infill walls to in-plane cyclic loading. Structures 3:306–319. https://doi.org/10.1016/j.istruc.2015.06.005
Srechai J, Lukkunaprasit P (2013) An innovative scheme for retrofitting masonry-infilled non-ductile reinforced concrete frames. Civ Struct Eng 6(4):277–288. https://doi.org/10.1080/19373260.2013.821716
Stafford SB (1962) Lateral stiffness of infilled frames. J Struct Div 88(6):183–226
Stavridis A, Shing PB (2010) Finite-element modeling of nonlinear behavior of masonry-infilled RC frames. J Struct Eng 136(3):285–296. https://doi.org/10.1007/s10518-017-0241-4
Su Q, Cai G, Cai H (2017) Seismic behavior of full-scale hollow brick-infilled RC frames under cyclic loads. Bull Earthq Eng 15(7):2981–3012. https://doi.org/10.1007/s10518-016-0074-6
Suthasit M, Warnitchai P (2018) Seismic performance of US-code conforming RC moment frames constructed with regularly distributed masonry infills. J Earthq Eng. https://doi.org/10.1080/13632469.2018.1493005
Tarque N, Candido L, Camata G, Spacone E (2015) Masonry infilled frame structures: state of the art review of numerical modelling. Earthq Struct 8(1):225–251
Torrisi GS, Crisafu FJ (2012) An innovative model for the in-plane nonlinear analysis of confined masonry and infilled frame structures. In: The 15th world conference on earthquake engineering, Lisbon, Portugal, pp 24–28
Tucker CJ (2007) Prediction the in-plane capacity of masonry infilled frames. Dissertation, Tennessee Technological University, Tennessee, USA
Yuen TYP, Zhang H, Kuang JS, Huang Q (2018) Shake table tests on RC frame infilled by slitted masonry panels. Bull Earthq Eng 16(9):4027–4052. https://doi.org/10.1007/s10518-018-0339-3
Zhang L, Jirsa JO (1982) A study of shear behavior of reinforced concrete beam-column joints. P.M. Ferguson Structural Engineering Laboratory Report, University of Texas at Austin, Texas, USA
Zovkic J, Sigmund V, Gulijas I (2012) Cyclic testing of a single bay reinforced concrete frames with various types of masonry infill. Earthq Eng Struct Dyn. https://doi.org/10.1002/eqe.2263
Acknowledgements
The authors gratefully acknowledge the financial support from the Thailand Research Funds (RDG6130022) and the King Mongkut’s University of Technology Thonburi’s Petchra Pra Jom Klao Ph.D. Scholarship to the first author.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Wararuksajja, W., Srechai, J. & Leelataviwat, S. Seismic design of RC moment-resisting frames with concrete block infill walls considering local infill-frame interactions. Bull Earthquake Eng 18, 6445–6474 (2020). https://doi.org/10.1007/s10518-020-00942-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10518-020-00942-9