Abstract
The need for seismic protection of structures located in earthquake prone areas of developing countries has motivated several investigations of low-cost seismic isolators in recent years. One of the most promising device is the Unbonded Fiber Reinforced Elastomeric Isolator (UFREI): in UFREIs no bonding or fastening is provided between the bearing and top–bottom supports and expensive thick steel plates are not required. The behavior of UFREIs is characterized by rollover and full-contact deformations under horizontal loads: the former decreases the effective stiffness of the isolation system, thus reducing the seismic demand, while the latter plays a key role in generating a hardening phase, thus limiting the horizontal displacement of the isolator under severe earthquakes. Such remarkable advantages highlight a great potential for world-wide UFREIs applications. However, until now there is no representative UFREI model available in structural analysis software codes. In this work, a comprehensive but simple UFREI model is implemented in an ABAQUS user element (UEL), taking into account non-linear, hardening and hysteretic behavior of the bearing: in addition, multiple DOFs are considered to simulate the complex 3D behavior of UFREIs, which is characterized by horizontal and vertical displacements, rotation and torsion. The effectiveness of the UEL model is evaluated performing 3D FE dynamic time history analyses on a rigid slab supported by four different types of UFREI. The results show that the UEL model can reasonably fit the behavior of the detailed FE model, significantly reducing the computational efforts of the analyses. The UEL model proposed in this study can be particularly suitable for 3D dynamic time history analyses of complex base isolated structures.
Similar content being viewed by others
References
Al-Anany YM, Tait MJ (2015) A numerical study on the compressive and rotational behavior of fiber reinforced elastomeric isolators (FREI). Compos Struct 133:1249–1266
Al-Anany YM, Van Engelen NC, Tait MJ (2017) Vertical and lateral behavior of unbonded fiber-reinforced elastomeric isolators. J Compos Constr 21:04017019
American Association of State Highways and Transportation Officials, AASHTO (2000) Guide specification for seismic isolation design, 2/e
Bruneau M, Engelhardt M, Filiatrault A, Goel SC, Itani A, Hajjar J, Leon R, Ricles J, Stojadinovic B, Uang CM (2005) Review of selected recent research on US seismic design and retrofit strategies for steel structures. Prog Struct Mater Eng 7(3):103–114
Calabrese A, Spizzuoco M, Serino G, Della Corte G, Maddaloni G (2015) Shaking table investigation of a novel, low-cost, base isolation technology using recycled rubber. Struct Control Health Monit 22:107–122
Cardone D, Perrone G (2012) Critical load of slender elastomeric seismic isolators: an experimental perspective. Eng Struct 40:198–204
Castellano A, Foti P, Fraddosio A, Marzano S, Mininno G, Piccioni MD (2014) Seismic response of a historic masonry construction isolated by stable unbonded fiber-reinforced elastomeric isolators (SU-FREI). Key Eng Mater 628:160–167
CEB-FIB (Comité Européen du Béton - Fédération Internationale du Béton) (2003) Seismic assessment and retrofit of reinforced concrete buildings. CEB-FIB Bulletin no. 24. International Federation for Structural Concrete, Task Group 7.1
Constantinou MC, Whittaker AS, Kalpakidis Y, Fenz DM, Warn GP (2007) Performance of seismic isolation hardware under service and seismic loading. Technical Report MCEER-07-0012
Das A, Deb SK, Dutta A (2016a) Comparison of numerical and experimental seismic responses of FREI-supported un-reinforced brick masonry model building. J Earthq Eng 20:1239–1262
Das A, Deb SK, Dutta A (2016b) Shake table testing of un-reinforced brick masonry building test model isolated by U-FREI. Earthq Eng Struct Dyn 45:253–272
De Raaf MGP, Tait MJ, Toopchi-Nezhad H (2011) Stability of fiber-reinforced elastomeric bearings in an unbonded application. J Compos Mater 45:1873–1884
Di Sarno L, Elnashai AS (2005) Innovative strategies for seismic retrofitting of steel and composite structures. Prog Struct Mater Eng 7(3):115–135
Di Sarno L, Elnashai AS (2009) Bracing systems for seismic retrofitting of steel frames. J Constr Steel Res 65:452–465
Ehsani B, Toopchi-Nezhad H (2017) Systematic design of unbonded fiber reinforced elastomeric isolators. Eng Struct 132:383–398
Eurocode 8 (2005) Design of structures for earthquake resistance-part 1: general rules, seismic actions and rules for buildings. European Committee for Standardization, Brussels
Fardis MN (2009) Seismic design, assessment and retrofitting of concrete buildings: based on EN-Eurocode 8. Springer, Berlin
Fardis MN, Schetakis A, Strepelias E (2013) RC buildings retrofitted by converting frame bays into RC walls. Bull Earthq Eng 11:1541–1561
FEMA (Federal Emergency Management Agency) (2000) (2000) FEMA 356: pre-standard and commentary for the seismic rehabilitation of buildings. FEMA, Washington
Fragiacomo M, Rajgelj S, Cimadom F (2003) Design of bilinear hysteretic isolation systems. Earthq Eng Struct Dyn 32(9):1333–1352
Giannuzzi D, Ballarini R, Hucklebridge A, Pollino M, Valente M (2014) Braced ductile shear panel: new seismic-resistant framing system. J Struct Eng ASCE 140(2):1–11
Habieb AB, Milani G, Tavio T, Milani F (2017a) Low cost frictional seismic base-isolation of residential new masonry buildings in developing countries: a small masonry house case study. Open Civ Eng J 11:1026–1035
Habieb A, Milani G, Tavio T, Milani F (2017b) Seismic performance of a masonry building isolated with low cost rubber isolators. WIT Trans Built Environ 172:71–82
Habieb A, Milani G, Tavio T, Milani F (2017c) Numerical model of low cost rubber isolators for masonry housing in high seismic regions. World Acad Sci Eng Technol Int J Civ Environ Struct Constr Archit Eng 11(5):590–596
Habieb A, Milani G, Tavio T, Milani F (2017d) FE modelling of fiber reinforced elastomeric isolators (FREI): mesh verification and validation. In: AIP conference proceedings, vol 1978, p 450006
Habieb AB, Milani G, Tavio T (2018a) Two-step advanced numerical approach for the design of low-cost unbonded fiber reinforced elastomeric seismic isolation systems in new masonry buildings. Eng Fail Anal 90:380–396
Habieb AB, Milani G, Tavio T, Milani F (2018b) Practical designs and seismic performances of residential masonry building isolated with fiber reinforced elastomeric isolators. In: 10th international masonry conference, Milan
Habieb AB, Valente M, Milani G (2018c) Base seismic isolation of a historical masonry church using fiber reinforced elastomeric isolators. Soil Dyn Earth Eng (accepted)
S.N. Indonesia (2013) Persyaratan beton struktural untuk bangunan gedung, SNI 2847
Jerrams SJ, Kaya M, Soon KF (1998) The effects of strain rate and hardness on the material constants of nitrile rubbers. Mater Des 19:157–167
Kelly JM (1993) Earthquake-resistant design with rubber. Springer, London
Kelly JM, Konstantinidis D (2007) Low-cost seismic isolators for housing in highly-seismic developing countries. In: 10th world conference on seismic isolation, energy dissipation and active vibrations control of structures, Istanbul, Turkey, pp 28–31
Kumar M, Whittaker AS, Constantinou MC (2014) An advanced numerical model of elastomeric seismic isolation bearings. Earthq Eng Struct Dyn 43:1955–1974
Kumar M, Whittaker AS, Constantinou MC (2015) Seismic isolation of nuclear power plants using elastomeric bearings. Technical Report MCEER-15-0008
Love JS, Tait MJ, Toopchi-Nezhad H (2011) A hybrid structural control system using a tuned liquid damper to reduce the wind induced motion of a base isolated structure. Eng Struct 33:738–746
Manzoori A, Toopchi-Nezhad H (2017) Application of an extended Bouc–Wen model in seismic response prediction of unbonded fiber-reinforced isolators. J Earthq Eng 21(1):87–104
Mishra HK, Igarashi A, Matsushima H (2013) Finite element analysis and experimental verification of the scrap tire rubber pad isolator. Bull Earthq Eng 11(2):1–21
Naeim F, Kelly JM (1999) Design of seismic isolated structures: from theory to practice. Wiley, Hoboken
Nagarajaiah S, Reinhorn AM, Constantinou MC (1991) Nonlinear dynamic analysis of 3-D-base-isolated structures. J Struct Eng 117:2035–2054
Osgooei PM, Tait MJ, Konstantinidis D (2017) Non-iterative computational model for fiber-reinforced elastomeric isolators. Eng Struct 137:245–255
Russo G, Pauletta M (2013) Sliding instability of fiber-reinforced elastomeric isolators in unbonded applications. Eng Struct 48:70–80
Shahzad M, Kamran A, Siddiqui MZ, Farhan M (2015) Mechanical characterization and FE modelling of a hyperelastic material. Mater Res 18:918–924
Simulia (2014) ABAQUS 6.14 user’s manual. Dassault Systems, Providence
Spizzuoco M, Calabrese A, Serino G (2014) Innovative low-cost recycled rubber-fiber reinforced isolator: experimental tests and finite element analyses. Eng Struct 76:99–111
Thuyet VN, Dutta A, Deb SK (2017) Evaluation of horizontal stiffness of fibre-reinforced elastomeric isolators. Earthq Eng Struct Dyn 46(11):1747–1767
Toopchi-Nezhad H (2014) Horizontal stiffness solutions for unbonded fiber reinforced elastomeric bearings. Struct Eng Mech 49:395–410
Toopchi-Nezhad H, Tait MJ, Drysdale RG (2008a) Testing and modeling of square carbon fiber-reinforced elastomeric seismic isolators. Struct Control Health Monit 15:876–900
Toopchi-Nezhad H, Tait MJ, Drysdale RG (2008b) Lateral response evaluation of fiber-reinforced neoprene seismic isolators utilized in an unbonded application. J Struct Eng 134:1627–1637
Toopchi-Nezhad H, Tait MJ, Drysdale RG (2011) Bonded versus unbonded strip fiber reinforced elastomeric isolators: finite element analysis. Compos Struct 93:850–859
Triantafillou TC (2001) Seismic retrofitting of structures with fibre-reinforced polymers. Prog Struct Mater Eng 3(1):57–65
Valente M, Milani G (2018) Alternative retrofitting strategies to prevent the failure of an under-designed RC frame. Eng Fail Anal 89:271–285
Van Engelen NC, Osgooei PM, Tait MJ, Konstantinidis D (2014) Experimental and finite element study on the compression properties of Modified Rectangular Fiber-Reinforced Elastomeric Isolators (MR-FREIs). Eng Struct 74:52–64
Van Engelen NC, Konstantinidis D, Tait MJ (2016) Structural and nonstructural performance of a seismically isolated building using stable unbonded fiber-reinforced elastomeric isolators. Earthq Eng Struct Dyn 45:421–439
Acknowledgements
A.B Habieb would like to acknowledge the financial support received from the Finance Ministry of Indonesian Republic (LPDP Scholarship) for performing his Ph.D. program at the Technical University of Milan, Italy.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Habieb, A.B., Valente, M. & Milani, G. Implementation of a simple novel Abaqus user element to predict the behavior of unbonded fiber reinforced elastomeric isolators in macro-scale computations. Bull Earthquake Eng 17, 2741–2766 (2019). https://doi.org/10.1007/s10518-018-00544-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10518-018-00544-6